Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Maretron TMP100 Exhaust Gas Temperature Probe TP-EGT-1
Summary of Contents for Maretron TMP100 Exhaust Gas Temperature Probe TP-EGT-1
- Page 1 ® ® TMP100 Temperature Module User’s Manual Revision 1.0 Copyright © 2008 Maretron, LLP All Rights Reserved Maretron, LLP 9014 N. 23 Ave #10 Phoenix, AZ 85021-7850 http://www.maretron.com Maretron Manual Part #: M002101 Revision 1.0 Page i...
-
Page 2: Revision History
TMP100 User's Manual Revision History Revision Description Original document Page ii Revision 1.0... -
Page 3: Table Of Contents
Technical Specifications ... 9 Technical Support ... 10 Installation Template ... 11 Maretron (2 Year) Limited Warranty ... 12 Figure 1 – Mounting the TMP100 ... 3 ® Figure 2 – NMEA 2000 Connector Face Views ... 4 Figure 3 –... - Page 4 TMP100 User's Manual Table of Appendices ® Appendix A – NMEA 2000 Interfacing ... A1 Page iv Revision 1.0...
-
Page 5: Introduction
TMP100 to the highest standards for years of dependable and accurate service. Maretron's TMP100 measures the temperature for up to 6 temperature probes and reports the information over an NMEA 2000 and 2 high temperature thermocouple probes. Optional thermistor probes (-20°C to 80°C or - 4°F to 176°F) cover a wide range of applications including cabin air temperature, engine room... -
Page 6: Tmp100 Accessories
• TP-EGT-1 TMP100 Exhaust Gas Temperature Probe 1.4 Quick Install Installing the Maretron TMP100 involves the following five steps. Please refer to the individual sections for additional details. 1. Unpack the box (Section 2.1) 2. Choose a mounting location (Section 2.2) 3. -
Page 7: Mounting The Tmp100
® ® NMEA 2000 network using a Maretron NMEA 2000 cable (or compatible cable) by connecting the female end of the cable to the TMP100 (note the key on the male connector and keyway on the female connector). Be sure the cable is connected securely and that the collar on the cable connector is tightened firmly. -
Page 8: Temperature Probe Connections
TMP100 User's Manual Figure 2 – NMEA 2000 2.4.2 Temperature Probe Connections The TMP100 temperature probe connections are made by connecting to the 12-pin terminal strip on the top of the unit. First, remove the four screws at the corners of the unit detaching the splash guard from the unit. -
Page 9: Exhaust Gas Temperature (Egt) Probe
® ® 2.4.2.1 Exhaust Gas Temperature (EGT) Probe The TP-EGT-1 exhaust gas temperature probe may be used to measure temperatures other than exhaust gas temperatures; however, the TP-EGT-1 exhaust gas temperature probe is the only TMP100 temperature probe that has sufficient range to measure exhaust gas temperature. -
Page 10: Checking Connections
You configure the TMP100 using a Maretron DSM250 display or other NMEA 2000 unit that is capable of configuring the TMP100. Please refer to the Maretron DSM250 User’s Manual for details. 2.5.1 Channel #0 - #1 Source You must configure the TMP100 as to what type of temperature measurement it is transmitting. -
Page 11: Channel #2 - #5 Source
Maretron N2KView Vessel Monitoring System and the Maretron DSM250 display. The label will let you assign an easy-to-remember text label (example: “Forward Bilge Pump”) to make it easy for you to identify the device as you are configuring the monitoring software or display, as well as when alerts are generated. -
Page 12: Installation Description
This configuration option will allow you to program the values of these fields. 3 Maintenance Regular maintenance is important to ensure continued proper operation of the Maretron TMP100. Perform the following tasks periodically: • Clean the unit with a soft cloth. Do not use chemical cleaners as they may remove paint or markings or may corrode the TMP100 enclosure or seals. -
Page 13: Technical Specifications
5 Technical Specifications As Maretron is constantly improving its products, all specifications are subject to change without notice. Maretron products are designed to be accurate and reliable; however, they should be used only as aids to navigation and not as a replacement for traditional navigation aids and techniques. -
Page 14: Technical Support
Corrosion (Salt Mist) Electromagnetic Emission Electromagnetic Immunity Safety Precautions 6 Technical Support If you require technical support for Maretron products, you can reach us in any of the following ways: Telephone: World Wide Web: Page 10 Temperature, High Range (Exhaust Gas... -
Page 15: Installation Template
® ® 7 Installation Template Please check the dimensions before using the following diagram as a template for drilling the mounting holes because the printing process may have distorted the dimensions. Figure 5 – Mounting Surface Template Revision 1.0 Page 11... -
Page 16: Maretron (2 Year) Limited Warranty
Maretron’s option, of any product not meeting the above limited warranty and which is returned to Maretron; or if Maretron is unable to deliver a replacement that is free from defects in materials or workmanship, Purchaser’s payment for such product will be refunded. - Page 17 Appendix A – NMEA 2000 ® TMP100 NMEA 2000 Periodic Data Transmitted PGNs PGN 130310 – Environmental Parameters (not recommended for new designs; included for backward compatibility) The TMP100 uses this PGN to provide a regular transmission of water temperature and outside air temperature.
- Page 18 TMP100 User's Manual PGN 130312 –Temperature The TMP100 uses this PGN to provide a regular transmission of various temperatures. The factory default for periodic transmission rate is once every two seconds. The transmission of this PGN can be disabled (see PGN 126208 – NMEA Request Group Function – Transmission Periodic Rate).