Related Manuals for Paitec ES-5000
Summary of Contents for Paitec ES-5000
- Page 1 Pressure Sealer ES-5000 ES-5000 User Manual <Rev. 09-01-30>...
-
Page 2: Table Of Contents
Pressure Sealer ES-5000 Table of Contents 1. Introduction 2. Installation 3. Features 1) Specifications 2) General views 4. How to Operate 1) Form Preparation 2) Loading forms 3) Start 4) Fold Setting 5) Operator Panel 6) Manual Feed 5. Maintenance... -
Page 3: Introduction
Pressure Sealer ES-5000 1. Introduction ES-5000 produces folded and sealed mailable documents with cut-sheet Pressure Seal forms. Pressure activated adhesive applied forms provide and instantly secure seal on all sides of the form, whether use a “C”, “V”, “Z” or “Double” fold. -
Page 4: Installation
Pressure Sealer ES-5000 2. Installation Locate the box right next to the location where the machine will be set up and operate. Open Box, Remove the Operators Guide and set aside. Grasp the two Shipping Straps and remove the unit from the box. -
Page 5: Features
Pressure Sealer ES-5000 1) Features 1) Specifications Processing Speed 4,200 forms per hour Automatic jam recovery system No adjustment required for varying paper thickness Fold plate setting can be changed in seconds Manual feeder for single form processing ... - Page 6 Pressure Sealer ES-5000 2.3) Exit Tray Stopper for Exit Tray 2.4) Label & Fuse AC Socket 5 Amp 250V Mini Fuse in a 1/4 Manufacturer’s Label with Turn Fuse Holder Serial No. 2.5) How to Open the Fold Unit (Please follow the pictures below in order)
- Page 7 Pressure Sealer ES-5000 2.6) How to open the Fold Drum (Please follow the pictures below in order) Folding Drum handle Folding Drum in the partially open position in the Unlock(down) position Folding Drum in the open position. Access the Folding Drum for clearing jams...
-
Page 8: How To Operate
Pressure Sealer ES-5000 3. How to operate 1) Form preparation Forms must be fanned properly on both sides to separate and eliminate any static that may have been induced by the laser printer 2) Loading forms Place the paper in the Paper tray in the correct orientation as indicated in the chart below. - Page 9 Pressure Sealer ES-5000 4) Fold Setting 4.1) Standard Folding Drum 4.1.1) Unlock the green release lever to set the fold position 4.1.2) Move the red arrow, First fold on the red knob to the fold position required according to the manual on the fold drum 4.1.3) Move blue arrow, Second fold according to the manual on the fold drum...
- Page 10 Pressure Sealer ES-5000 5) Operator Panel 5.1) Power Switch: Power On/Off 5.2) Reset: Reset button will clear the display count 5.3) Start/Stop: Start/Stop button will start or stop the Feed cycle 5.4) Counter: Display will show the total page count/resettable as well as Firmware Rev.
-
Page 11: Maintenance
Pressure Sealer ES-5000 Maintenance 1) General Cleaning Be sure that the room is well ventilated, Switch off the mains power and unplug or disconnect from the mains, Pull out the fold drum and the fold unit, Remove as much paper dust as possible using a soft brush... - Page 12 Pressure Sealer ES-5000 4) Cleaning Press Rollers With general use, toner will build up on the Press rollers. Check the rollers for build up and clean on a regular basis with roller cleaning fluid. Depending on the type of laser printer, toner and fuser, the degree of build up will vary.
-
Page 13: Trouble Shooting
Pressure Sealer ES-5000 Trouble Shooting 1) Paper Jam 1.1) Feeding Unit Jam Do not pull the document backward in the event of jam in the Infeeder. Open the Fold Drum Unit by pushing down the Fold Drum handle as the... - Page 14 Pressure Sealer ES-5000 1.3) Press Unit Jam Fully extend the Folding Unit to the direction of the red arrow in the picture on the right Use the Jam Removal Tool to rotate the rollers by placing the tool into the jam...
- Page 15 Pressure Sealer ES-5000 2) Double Feed 2.1) Clean the Pickup rollers and pad with an alcoholic solution(In case problem persists, then go to 2.2) 2.2) Slide In-feed tray tension adjusters upwards (Manufacturer’s default position: middle). Both tension adjusters must be in...
- Page 16 Pressure Sealer ES-5000 4.7) Clean the fold rollers with an alcoholic solution 4.8) Examine and replace any folding roller with imperfections such as flat spots or swelling 4.9) Replace or exchange from side to side the folding roller compression springs Division of Pai Trading, Inc.
- Page 17 Fold Settings ES5000 - IM4000 - IM9500 ES2000 - ES7000 - MX6000 - MX8000 Drum First Second First Second Size and Fold Type inches inches inches inches 7-1/3 3-2/3 3-2/3 3-2/3 11” Z-Fold 9-1/3 4-2/3 4-2/3 4-2/3 14” Z-Fold 8-3/4 5-1/4 5-1/4 5-1/4...
- Page 18 ES5000 Folding Diagram C & V Fold Drum IM4000 Z-Fold IM9500 In-feed direction Out-feed C-Fold In-feed Out-feed V-Fold In-feed direction Out-feed 1st Fold 2nd Fold Fold Plates Set at Zero 73 mm 0 mm Minimum 0 in 2.875 in 220 mm 150 mm Maximum 8.667 in...
- Page 19 ES5000L Folding Diagram Z Fold Drum IM4000L IM9500 Z14-Fold In-feed direction Out-feed 1st Fold 2nd Fold Fold Plates 181 mm 79 mm Minimum 3.1 in 7.25 in 238 mm 140 mm Maximum 9.33 in 5.5 in Z-Fold 11” = Z 14”...
- Page 20 Z Fold Drum Settings By looking at the Customer’s Form, determine the Size of Paper and Type of Fold. blue slider on the front of your drum is your first fold position marker (There are basic instructions on the drum to help you.) Remember unlock the first fold locking lever (Green...
- Page 21 Z Fold Drum Settings Cont…. The second fold position is located inside the drum. Unlock the fold drum release lever (this has a black plastic ball on the shaft) the drum will drop forward. Now you can see the second fold plate and settings… You must loosen the 2 thumb screws to move the slider to the required setting.