Advertisement
Quick Links
Advertisement
Related Manuals for Paitec ES-5000
Summary of Contents for Paitec ES-5000
-
Page 1: User Manual
Pressure Sealer ES-5000 ES-5000 User Manual <Rev. 09-01-30>... -
Page 2: Table Of Contents
Pressure Sealer ES-5000 Table of Contents 1. Introduction 2. Installation 3. Features 1) Specifications 2) General views 4. How to Operate 1) Form Preparation 2) Loading forms 3) Start 4) Fold Setting 5) Operator Panel 6) Manual Feed 5. Maintenance 1) General Cleaning 2) Paper Dust 3) Cleaning Pickup and Fold Rollers... -
Page 3: Introduction
Pressure Sealer ES-5000 1. Introduction produces folded and sealed mailable documents with cut-sheet Pressure Seal forms. Pressure activated adhesive applied forms provide and instantly secure seal on all sides of the form, whether use a “C”, “V”, “Z” or “Double” fold. Names of each part... -
Page 4: Installation
Pressure Sealer ES-5000 2. Installation Locate the box right next to the location where the machine will be set up and operate. Open Box, Remove the Operators Guide and set aside. Grasp the two Shipping Straps and remove the unit from the box. Remove all packing materials from around the unit and place the folder on a sturdy ... -
Page 5: Features
Pressure Sealer ES-5000 1) Features 1) Specifications Processing Speed 4,200 forms per hour Automatic jam recovery system No adjustment required for varying paper thickness Fold plate setting can be changed in seconds Manual feeder for single form processing ... - Page 6 Pressure Sealer ES-5000 2.3) Exit Tray Stopper for Exit Tray 2.4) Label & Fuse AC Socket 5 Amp 250V Mini Fuse in a 1/4 Manufacturer’s Label with Turn Fuse Holder Serial No. 2.5) How to Open the Fold Unit (Please follow the pictures below in order) Folding Unit Pulls out by grasping the hand hold and pull out...
- Page 7 Pressure Sealer ES-5000 2.6) How to open the Fold Drum (Please follow the pictures below in order) Folding Drum handle Folding Drum in the partially open position in the Unlock(down) position Folding Drum in the open position. Access the Folding Drum for clearing jams...
-
Page 8: How To Operate
Pressure Sealer ES-5000 3. How to operate 1) Form preparation Forms must be fanned properly on both sides to separate and eliminate any static that may have been induced by the laser printer 2) Loading forms Place the paper in the Paper tray in the correct orientation as indicated in the chart below. - Page 9 Pressure Sealer ES-5000 4) Fold Setting 4.1) Standard Folding Drum 4.1.1) Unlock the green release lever to set the fold positio 4.1.2) Move the red arrow, First fold on the red knob to the fold position required according to the manual on the fold drum 4.1.3) Move blue arrow, Second fold according to the manual on the fold drum 4.1.4) Once the fold position properly is done, lock back the green release lever (Red knob is the first fold setting, Blue know is the second fold setting)
- Page 10 Pressure Sealer ES-5000 5) Operator Panel 5.1) Power Switch: Power On/Off 5.2) Reset: Reset button will clear the display count 5.3) Start/Stop: Start/Stop button will start or stop the Feed cycle 5.4) Counter: Display will show the total page count/resettable as well as Firmware Rev.
-
Page 11: Maintenance
Pressure Sealer ES-5000 Maintenance 1) General Cleaning Be sure that the room is well ventilated, Switch off the mains power and unplug or disconnect from the mains, Pull out the fold drum and the fold unit, Remove as much paper dust as possible using a soft brush 2) Paper Dust With general use, paper dust will build up inside the machine and can be cleared by suing an can of invertible Air Duster, which will apply a short burst of compressed... - Page 12 Pressure Sealer ES-5000 4) Cleaning Press Rollers With general use, toner will build up on the Press rollers. Check the rollers for build up and clean on a regular basis with roller cleaning fluid. Depending on the type of laser printer, toner and fuser, the degree of build up will vary. Clean both Upper &...
-
Page 13: Trouble Shooting
Pressure Sealer ES-5000 Trouble Shooting 1) Paper Jam 1.1) Feeding Unit Jam Do not pull the document backward in the event of jam in the Infeeder. Open the Fold Drum Unit by pushing down the Fold Drum handle as the direction of the red arrow in the picture on the right Pull the paper to the direction of the red... - Page 14 Pressure Sealer ES-5000 1.3) Press Unit Jam Fully extend the Folding Unit to the direction of the red arrow in the picture on the right Use the Jam Removal Tool to rotate the rollers by placing the tool into the jam Removal holes as shown in the picture on the right Turn it downward.
- Page 15 Pressure Sealer ES-5000 2) Double Feed 2.1) Clean the Pickup rollers and pad with an alcoholic solution(In case problem persists, then go to 2.2) 2.2) Slide In-feed tray tension adjusters upwards (Manufacturer’s default position: middle). Both tension adjusters must be in the same position as shown in the picture on the right(In case the problem persists, then go to 2.3)
- Page 16 Pressure Sealer ES-5000 4.7) Clean the fold rollers with an alcoholic solution 4.8) Examine and replace any folding roller with imperfections such as flat spots or swelling 4.9) Replace or exchange from side to side the folding roller compression springs Division of Pai Trading, Inc.