Download Print this page

Dell SonicWALL TZ300 Quick Start Manual

Hide thumbs

Advertisement

Dell SonicWALL TZ300 Quick Start Guide
Dell SonicWALL™ TZ300
Quick Start Guide
Regulatory Model Number: APL28-0B4
Connect the interfaces
3
• Connect the WAN interface (X1) to your Internet
connection using a standard Ethernet cable.
• Connect the LAN interface (X0) to your computer
using a standard Ethernet cable.
Figure 3. Connecting WAN and LAN interfaces
Internet
TZ300 front and back panels
Figure 1. Front and back panels
Front Panel
Top - 10/100 Mbps when lit
1000
U0
X0
X1
X2
X3
X4
SonicWALL TZ300
10/100/act
1000/act
ss
lan
wan
Power
Bottom - 1 Gbps when lit
Test
USB 3.0 port
Fast blinking is initializing
Slow blinking is SafeMode
Service
For future use
Rear Panel
power
wan
lan
console
X4
X3
X2
X1
X0
Power
Console
X0 LAN Port
Port
X1 WAN Port
X4/X3/X2
Configurable ports
Run the Setup Wizard
4
• In the Web browser on your computer, navigate to
https://192.168.168.168.
http://192.168.168.168/
TIP:
Your computer should be using DHCP IP
addressing.
• In the window that opens, click on the word
in the line that says, "To launch the Dell
SonicWALL Setup Wizard, click here."
Check package contents
1
Verify that your package has the following contents:
• Dell SonicWALL appliance
• Ethernet cable
• Standard power adaptor
• Standard power cord
• Quick Start Guide
NOTE:
The included power cord is approved for use
only in specific countries or regions. Before using a
power cord, verify that it is rated and approved for
use in your location.
Figure 2. Package Contents
1000
U0
SonicWALL TZ300
X0
X1
X2
X3
ss
lan
wan
• The SonicOS Startup Guide opens.
• Click Next and follow the prompts in the Startup
Guide pages that follow.
• Enter the TZ appliance administrator credentials
to change the password, if you wish. Click Next.
here
NOTE:
The default administrator credentials are
Username: admin Password: password
Power on
2
• Connect the power adaptor to the appliance and to
the power cable. Plug the power cable into an
appropriate outlet (110-240 volts).
Internet
• The TZ appliance powers on and the Test LED
blinks during the boot sequence.
SonicWALL TZ300
X4
10/100/act
1000/act
SonicWALL TZ300
• The automatic WAN IP settings are displayed.
Click Next.
NOTE:
For manual configuration, refer to the
SonicOS 6.2 Administration Guide.
• The new IP Configuration is displayed. Click Done.
120V AC
(U.S.)
1000
U0
X0
X1
X2
X3
X4
10/100/act
1000/act
ss
lan
wan
1000
U0
X0
X1
X2
X3
X4
10/100/act
1000/act
ss
lan
wan

Advertisement

loading

  Summary of Contents for Dell SonicWALL TZ300

  • Page 1 • The new IP Configuration is displayed. Click Done. • In the window that opens, click on the word here Internet in the line that says, “To launch the Dell SonicWALL Setup Wizard, click here.” NOTE: The default administrator credentials are...
  • Page 2: Register Product

    Prüfen Sie den Anschluss des Geräts an die Stromversorgung, damit der Überstromschutz sowie die used in this document to refer to either the entities claiming the marks and names or their products. Dell elektrische Leitung nicht von einer eventuellen Überlastung der Stromversorgung beeinflusst werden.