Table of Contents
Advertisement
Cyclo Model 12A
Pneumatic
Dual Head Orbital Polisher
Instruction Manual
CONTENTS
SAFETY INSTRUCTIONS .................................................................................................. 1
DETAILING BASICS .......................................................................................................... 2
CYCLO POLISHER SET-UP .............................................................................................. 3
GUIDE TO GENUINE CYCLO ACCESSORIES ................................................................. 5
MACHINE OPERATING INSTRUCTIONS ......................................................................... 8
USER MAINTENANCE & TROUBLESHOOTING .............................................................. 9
TECHNICAL SPECIFICATIONS ....................................................................................... 10
PARTS DIAGRAMS AND LISTING .................................................................................. 11
APPLICATION AND ACCESSORIES QUICK GUIDE ..................................................... 11
Cyclo Toolmakers, Inc., 1740 Skyway Drive, Bldg. C, Longmont, CO 80504-5556 USA
Phone: +1-303-485-1990, Fax: +1-303-723-8680,
www.cyclotoolmakers.com
Advertisement
Table of Contents
Related Manuals for CYCLO 12A
Summary of Contents for CYCLO 12A
-
Page 1: Table Of Contents
USER MAINTENANCE & TROUBLESHOOTING .............. 9 TECHNICAL SPECIFICATIONS ..................10 PARTS DIAGRAMS AND LISTING .................. 11 APPLICATION AND ACCESSORIES QUICK GUIDE ............. 11 Cyclo Toolmakers, Inc., 1740 Skyway Drive, Bldg. C, Longmont, CO 80504-5556 USA Phone: +1-303-485-1990, Fax: +1-303-723-8680, www.cyclotoolmakers.com... -
Page 2: Safety Instructions
Model 12A Pneumatic Dual Head Orbital Polisher. The entire manual should be read carefully before using the Cyclo Dual Head Orbital Polisher and retained for future reference. Employers are responsible for ensuring that employees are provided with a copy of these instructions and adequate training prior to operating the tool. -
Page 3: Detailing Basics
Loose and spinning attachment strings can entangle your fingers or snag on the workpiece. DETAILING BASICS This section presents the basic steps involved in vehicle detailing, much of which is accomplished without your Cyclo polisher. More instructions on polisher operation are provided later in this manual. -
Page 4: Cyclo Polisher Set-Up
The removal of swirls and holograms is accomplished by removing scratches. the fine scratches. Your Cyclo polisher does this with the right combination of liquid compounds, polishes and pads and the correct technique. If a scratch catches your fingernail then it’s likely too deep to remove. Polishing the scratched area is still recommended. However, do so with the idea that you are attempting to make the defect less noticeable but not to remove it entirely. - Page 5 Rubber Pad Holders fit directly over the Head Assemblies. Quick Connect Adapters (79-725-5/16) • Center pads easily and save time by simply snapping the pads in place. System replaces Cyclo Polisher heads to hold 77- Series Double-Precision, two-sided pads. Scrubbing Brushes (76-xxx) •...
-
Page 6: Guide To Genuine Cyclo Accessories
Guide to Genuine Cyclo Accessories The following information will assist you in selecting the appropriate accessory for use with the Cyclo Polisher. For additional tips and application guides, please refer to the application chart included on the back cover of this manual. - Page 7 Your Cyclo polisher is also a scrubber. Fitted with Genuine Cyclo brushes, its action mimics the motion of hand-scrubbing. By simply attaching two Cyclo Brushes to the heads you can clean carpet, upholstery, boat decks, tile, grout and more. The orbiting motion of the Cyclo machine brushes combined with the brushes’...
- Page 8 Drying exterior surfaces Genuine Cyclo Discs Genuine Cyclo ProShine (cushioned abrasive “Micro-Mesh”) discs and Fast Discs (non-woven scrubbing discs similar to a soft Scotch-Brite) are handy for scratch removal and floor and board cleaning. ProShine Discs require a 72-920 ProShine™ Interface Pad that fits between a Velcro attachment system (Rubber Pad Holders or ProGuard Orbital Backing Plates;...
-
Page 9: Machine Operating Instructions
Cleaner on the pad face, work in, and let soak in a container of water-diluted Pad Cleaner. After soaking, rinse out, and if clean, place the items back on the Cyclo Polisher and run for a few seconds. Allow the action of the machine to shake excess water from the pad. You may also just squeeze dry (do not twist or wring). -
Page 10: User Maintenance & Troubleshooting
Timing: The secret of the operation of your Cyclo Polisher lies in the fact that the two heads are timed exactly 180 degrees apart. This is necessary for the balanced operation of the tool. If the machine is disassembled, use the following procedures to insure proper timing of the heads. -
Page 11: Technical Specifications
THE APPEARANCE OF YOUR CYCLO POLISHER Each of our Cyclo Polishers are hand crafted with the same superior level of quality and workmanship. As all handmade items will vary slightly, we cannot guarantee that each polisher will be identical with every other one of our polishers. You may notice light sanding or buffing marks in the hand- finished aluminum castings. -
Page 12: Parts Diagrams And Listing
Entire contents ©2005-2011 Cyclo Toolmakers, Inc. All rights reserved. CYCLO, ORBIT CLUB, PROGUARD, VES, FASTCUT, CTI PRO PAINT CARE, CTI 1 PASS EXPRESS, FREE FLITE and Cyclo Toolmakers, Inc logo are registered and unregistered trademarks of Cyclo Toolmakers, Inc. VELCRO is a registered trademark of Velcro USA and its affiliated companies.
Need help?
Do you have a question about the 12A and is the answer not in the manual?
Questions and answers