Advertisement
CYCLO DUAL HEAD ORBITAL POLISHER/SCRUBBER
MODELS 5, 5-Pro, 5C, 5C-Pro, 6CE AND 6CE-Pro
SAFETY MANUAL
Distributed by Hruby Orbital Systems, Inc.
CONTENTS
SAFETY INSTRUCTIONS ..................................................................................................... 1
CYCLO SCRUBBER SET-UP ................................................................................................ 3
MACHINE OPERATING INSTRUCTIONS ............................................................................ 4
USER MAINTENANCE & TROUBLESHOOTING ................................................................. 5
TECHNICAL SPECIFICATIONS ........................................................................................... 7
PARTS DIAGRAMS AND LISTING ....................................................................................... 9
RUPES USA, Inc., 14320 Longs Peak Court, Longmont, CO 80504-9698 USA
Phone: +1-970-535-0100, Fax: +1-303-723-8680, www.cyclotoolmakers.com
1
© RUPES USA, Inc., 2015 Rev2015.05.12_Hruby
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for CYCLO 5-Pro
Summary of Contents for CYCLO 5-Pro
-
Page 1: Table Of Contents
CYCLO DUAL HEAD ORBITAL POLISHER/SCRUBBER MODELS 5, 5-Pro, 5C, 5C-Pro, 6CE AND 6CE-Pro SAFETY MANUAL Distributed by Hruby Orbital Systems, Inc. CONTENTS SAFETY INSTRUCTIONS ..................... 1 CYCLO SCRUBBER SET-UP ....................3 MACHINE OPERATING INSTRUCTIONS ................4 USER MAINTENANCE & TROUBLESHOOTING ..............5 TECHNICAL SPECIFICATIONS ................... -
Page 2: Safety Instructions
This instruction manual is furnished with each Cyclo Model 5, 5-Pro, 5C, 5C-Pro, 6CE & 6CE-Pro Electric Dual Head Orbital Polisher. The entire manual should be read carefully before using the Cyclo Dual Head Orbital Polisher and retained for future reference. - Page 3 Grounding Instructions The Cyclo Polisher should always be electrically grounded while in use to protect the operator from electric shock. This tool is equipped with an approved three-conductor cord and three-prong grounding type plug to fit the proper grounding type receptacle. The green or green/yellow conductor wire in the cord is the grounding wire.
-
Page 4: Cyclo Scrubber Set-Up
The proper precut length is available from Cyclo Toolmakers or your dealer. When re-installing, be sure not to cover any part of the “1” or “0” (on/off) indicators embossed in the aluminum handle. -
Page 5: Machine Operating Instructions
Your Cyclo polisher is also a scrubber. Fitted with Genuine Cyclo brushes, its action mimics the motion of hand-scrubbing. By simply attaching two Cyclo Brushes to the machine you can clean carpet, upholstery, boat decks, tile, grout and more. The orbiting motion of the Cyclo machine brushes combined with the brushes’... -
Page 6: User Maintenance & Troubleshooting
Be sure the polisher is disconnected from the electrical supply before any inspection or maintenance is performed. The motor is only for the voltage specified on the nameplate. Voltage should not vary more than 10% over or under the voltage shown on the nameplate. Although the Cyclo Polisher is built to last a lifetime, it can encounter problems from heavy wear and tear. - Page 7 Timing: The secret of the operation of your Cyclo Polisher lies in the fact that the two heads are timed exactly 1/2 turn apart. This is necessary for the balanced operation of the tool. If the machine is disassembled, use the following procedures to insure proper timing of the heads.
-
Page 8: Technical Specifications
Intertek ETL SEMKO for CE EMC and Safety (per EN 60745-1, -2,-3) and S&V Solutions for noise (ISO 15744 and EN 0745) and hand-arm vibration (ISO 20643 and EN/ISO 28927) CYCLO POLISHER PARTS DIAGRAMS Model 5, 5C, 5-Pro & 5C-Pro, 6CE Parts and Wiring Diagrams... - Page 9 CYCLO DUAL HEAD ORBITAL POLISHER Model 6CE Wiring Highlight Model 5 & 5C Wiring Highlight PARTS LIST...
-
Page 10: Parts Diagrams And Listing
Entire contents ©2005-2015 RUPES USA, Inc. All rights reserved. CYCLO, ORBIT CLUB, PROGUARD, VES, FASTCUT, CTI PRO PAINT CARE, CTI PAD CARE, CTI 1 PASS EXPRESS, FREE FLITE and Cyclo Toolmakers, Inc logo are registered and unregistered trademarks of RUPES USA, Inc. VELCRO is a registered trademark of Velcro USA and its affiliated companies.
Need help?
Do you have a question about the 5-Pro and is the answer not in the manual?
Questions and answers