Related Manuals for HMM Diagnostics smartLAB indi
Summary of Contents for HMM Diagnostics smartLAB indi
- Page 1 Fully automatic wrist-cuff blood pressure monitor User Manual Please read this user manual thoroughly before first using the blood-pressure monitor. HMM Diagnostics GmbH D-69221 Dossenheim, Germany www.hmm.info...
-
Page 3: Table Of Contents
Content I. Introduction Normal blood pressure fluctuation II. Your smartLAB indi ® Display & functions Product description Specifications Note III. Setup & Operating procedures Battery loading Clock Mode Clock Adjusting Connecting the cuff to the monitor Applying the cuff Body posture during measurement Measuring Process... - Page 4 Displaying stored results Erasing results IV. Miscellaneous Assessing high blood pressure for adults Knowledge on Blood Pressure Troubleshooting Maintenance Explanation of Symbols Warranty...
-
Page 5: Introduction
I. Introduction Thank you for using the smartLAB indi wrist-cuff blood pressure monitor. ® With this device you can easily control your blood-pressure values and pulse rate and store the measured data. With its colored Bi-Classification LEDs, all results on the meter can be classified according to their value. Please read this manual thoroughly, before first using your smartLAB indi wrist- ®... - Page 6 Considering the above information, it is recommended that you measure your blood pressure at approximately the same time each day. Please always relax a minimum of 3 to 5 minutes between measurements to allow the blood circulation in your arm to recover. It is rare that you obtain identical blood pressure readings each time.
-
Page 7: Your Smartlab
II. Your smartLAB indi ® Display & functions SYS Classification systolic mmHg START button diastolic mmHg MEM button pulse DIA Classification /min... - Page 8 Set Contents 1 smartLAB ® indi Blood Pressure Monitor 1 User Manual 1 smartLAB ® Plastic Box 2 „AAA“ batteries...
-
Page 9: Product Description
Product description Based on oscillometric method and silicon integrate pressure sensor tech- nology, blood pressure and heart rate can be measured automatically and non-invasively. The LCD display will show blood pressure, pulse rate and irregular heart beat (if any). The most recent 60 measurements can be stored in the memory with date and time stamp. -
Page 10: Note
Note: 1. Stay quite, calm and rest for 5 minutes before blood pressure measurement. 2. The cuff should be placed at the same level as your heart. 3. During measurement, neither speak nor move your body and arm. 4. Measuring on same wrist for each measurement. 5. - Page 11 microwave oven, etc. 10. If Irregular Heartbeat (IHB) brought by common arrhythmias is detected in the procedure of blood pressure measurement, this signal will be displayed: Under this condition, the smartLAB indi can keep function, but ® the results may not be accurate, it’s suggested that you consult with your physician for accurate assessment.
-
Page 12: Setup & Operating Procedures
III. Setup & Operating procedures Battery loading • Open battery cover at the back of the monitor. • Load two “AAA” size batteries. Please pay attention to polarity. • Close the battery cover. When LCD shows battery symbol replace all batteries with new ones. -
Page 13: Clock Mode
Clock Mode Once you install the battery, two “beep” later, the LCD will display the time and date by turns. Clock Adjusting • When the smartLAB indi is in Clock Mode, press the START and ® MEM button at the same time, the machine enters Manual Clock Adjusting mode, the number of year will twinkle first. -
Page 14: Connecting The Cuff To The Monitor
the minute is twinkling, then the time and date is confirmed. • Your smartLAB indi will turn off automatically after 1 minute of ® no operation with the time and date unchanged. • Once you change the batteries, you will have to readjust clock. Connecting the cuff to the monitor The cuff is attached to your smartLAB indi when it is packaged. -
Page 15: Applying The Cuff
Applying the cuff Place the cuff around a bare wrist 1-2cm above the wrist joint on the palm side of the wrist. • While seated, place the arm with the cuffed wrist in front of your body on a desk or table with the palm up. If the cuff is correctly placed, you can read the LCD display. -
Page 16: Body Posture During Measurement
Body posture during measurement Sitting Measurement – Recommended Position • Sit upright • Place palm upside in front of you on a flat surface such as a desk or table, with your elbow resting on a chair or table • The cuff should be at the same level as your heart. •... - Page 17 • If it already has memory, LCD will show the latest result. If your smartLAB indi has not stored any memory, the LCD will show six “0”. ® The Bi-classification LED will lighten with the colour that indicates the blood pressure classification of the result. •...
-
Page 18: Displaying Stored Results
• After measurement, your smartLAB indi will turn off automatically ® after 1 minute of no operation. Alternatively, you can press the “START” button to turn off the monitor manually. • During measurement, you can press the “START” button to turn off the monitor manually. -
Page 19: Erasing Results
• The Bi-classification LED will also indicate the blood pressure classification. • Press “MEM” button again after the last memory, the monitor will power off. In the reviewing mode, it will automatically power off after 1 minute of no use. Alternatively, you can press the “START” button to shut down the smartLAB indi. -
Page 20: Miscellaneous
will be deleted after three “beep”. By pressing the button “MEM” or “START”, the monitor will turn off. IV. Miscellaneous Assessing high blood pressure for adults The following guidelines for assessing high blood pressure (without regard to age or gender) have been established by the World Health Organizati- on (WHO). -
Page 21: Knowledge On Blood Pressure
Knowledge on Blood Pressure: Your heart is just like a pump which causes the blood to circulate through all vessels. As a result, the blood pressure is the pressure on the wall of the blood vessel pressed by blood. The output of blood from the heart when it is a systole is called systolic pressure. - Page 22 Reason sytolic pressure diastolic pressure high high • • Drinking, smoking • • Excitement or sporting • • seeing a doctor, desire to urinate • • change of tem- high perature • • • • After bathing, deep breathing or yawning •...
- Page 23 The blood pressure is influenced by a variety of different factors, such as bodily circumstances or a wrong operation of the monitor. Some people even get nervous when seeing a doctor and that will make their blood pres- sure rise. Single measurements can not indicate the whole blood level, so you need not to be anxious for isolated higher or lower blood pressure results.
- Page 24 Male Female systolic diastolic systolic diastolic 11-15 16-20 21-25 26-30 31-35 36-40 41-45 46-50 51-55 56-60 61-65...
- Page 25 Hypertension: Various cardiovascular or kidney diseases can cause hypertension. Long- term hypertension can also cause pathological changes in heart, brain and kidney. These changes can lead to hypertension complications which are often diagnosed or treated too late. Low Blood Pressure: There are two kinds of minimum pressure: •...
- Page 26 Classifica- Color indicator Color changing tion mmHg mmHg area Optimal < 120 < 80 GREEN GREEN Normal 120-129 80-84 GREEN GREEN High- 130-139 85-89 GREEN GREEN Stage 1 140-159 90-99 YELLOW YELLOW Hypertension Stage 2 160-179 100-109 ORANGE Hypertension Stage 3 ≥180 ≥110 Hypertension...
-
Page 27: Troubleshooting
Additionally, the Bi-classification LED will display the corresponding colour respective for the Systolic and the Diastolic. Example: if the systolic value is 161 (which is Stage 2 Hypertension), the LED for the Systolic (which is upper) should display red. And if the diastolic value is 89 (which is High-normal), the LED for the Diastolic (which is lo- wer) should display green. - Page 28 Problem Cause Remedy LCD shows „Er 3“ Pneumatic system is blocked or cuff is too tight during in- Place the cuff correctly and flation try again LCD shows „Er 4“ Pneumatic system leak or cuff is too loose during inflation LCD shows „Er 5“...
-
Page 29: Maintenance
Maintenance 1. Do not drop this monitor or subject it to strong impact. 2. Avoid high temperature and solarization. Do not immerse the monitor in water as this will result in damage to the monitor. 3. If this monitor is stored near freezing, allow it to acclimate to room temperature before use. -
Page 30: Explanation Of Symbols
Disposal Information Warranty HMM Diagnostics GmbH products need to fulfill high quality requirements. Because of this reason, HMM Diagnostics GmbH gives a 2-year warranty by purchasing this smartLAB product. You can even extend the warranty from ® 2 to 5 years without extra pay when you register your product. Please use the warranty card included in your product set. - Page 31 Manufacturer: HMM Diagnostics GmbH Friedrichstr. 89 D-69221 Dossenheim, Germany mail: info@hmm.info www.hmm.info Weitere Informationen zu den smartLAB Produkten / ® More information on our smartLAB products: ® www.smartlab.org...