Page 2
You must monitor your unit DAILY. If unit is in “Alarm”, unplug the unit inmediately. Always check for any water (condensate) leaks. Vintage Keeper will not be liable or responsible for incidental or consequential damages. (See Warranty). Place unit in a clean area and allow access to the exterior surfaces for periodic vacuuming of the condensor coil.
Page 3
HARDWARE KIT Base Support Connector Clip Rubber Ring Silver Clip Screw Coupler Shelf Rubber Cord Washer Coupler Hanger Screw Hinge Silicone Caulking Hex Bolt Hanger Strips Hex Wrench MODEL STEPS 1. Panel Preparation (A,B,K). 2. Cabinet Assembly (C,J,O). 3. Hinge, Base and Legs Installation (D,E,F,G,H,I). 4.
Page 6
STEP 2 : CABINET ASSEMBLY CONTINUED Insert the BOTTOM and TOP PANEL SLIGHTLY stretch the SIDE PANELS, start inserting the BOTTOM (rear) side rst and work upwards, then push or hammer with a rubber mallet around sides. DO NOT HIT THE CENTER OF THE PANELS! TOP PANEL can be identied by...
Page 7
STEP 3 : HINGE,BASE AND LEGS INSTALLATION Fasten BASE (D) with OPTIONAL: Seal all panel joints (indicated by grey arrows) BOLTS (H) with the supplied silicone (O). Continue in steps 5 and 7. Fasten one HINGE (G) to each SIDE of the cabinet NOTE: Hinge can be on either side of the cabinet (FRONT BASE has to be set with end tabs away from front...
Page 8
STEP 4 : SHELVES COUPLER SHELVES Install COUPLER SHELVES between the VERTICAL COUPLER and the BACK PANEL, hook them on the COUPLER HANGERS (J) Install 4 HANGERS STRIPS (M), hook- ing them to the COUPLER SHELVES through square holes. (Watch for ori- entation, all hooks have to point upwards).
Page 9
STEP 5 : COOLING UNIT INSTALLATION Lift the COOLING UNIT to top shelf NOTE : Place it on a spacer (phone- book or pieces of left-over insulation) to get it level with the cut-off of the BACK panel COOLING Take out the power cord through the UNIT BACK panel...
Page 10
STEP 6 : FACEPLATE AND LIGHT INSTALLATION Open the RUBBER RING (N) at cut end and place it around the cord Plug in the light cord into the side of COOLING UNIT NOTE: Place the ring into the notch of the FACEPLATE 1.
Page 11
STEP 7 : DOORS INSTALLATION Open box V3 Place WASHERS (F) on BOTTOM HINGES (G) Insert DOORS onto BOTTOM HINGES(G) OPTIONAL: Seal all panel joints (indicated by grey arrows) with the supplied silicone (O). Install TOP HINGES (G) with HEX BOLTS (H) NOTE : Adjust nal position of the doors before tightening the bolts...
Page 12
CONTROLS : PLUG IT IN and ENJOY! (wait one minute) DEFAULT SETTINGS Storage Temperature : 57°F / 14°C (ideal temp for wine cellaring) Fan Speed: DEFAULT. Optimized for maximum efciency and moderate noise Display: SET - POINT (°F) FEATURES Digital Sensor: Sensing ACTUAL TEMP (air in cabinet)** ** Reading AIR temperature the controller will respond more quickly Set temp range: 50°F / 72°F (check humidity and temperature...
Page 13
MAXIMUM CAPACITIES AND LOADING TIPS Maximum capacities and sample loading arrangements for Vintage Keeper Tuscany wine cellars are illustrated below. Note the variations in shelf height, to accomodate the widest variety of bottle types and sizes. Standard Burgundy and Bordeaux bottles are best arranged with necks facing out;...
Page 14
Fourth, install a high quality surge supressor to protect against sudden power uctuations. Fifth, clean the unit as directed, on a regular basis. Be advised, also, that Drobot-Vintage Keeper cannot in any event be liable or responsible for incidental or consequential damages.
Page 15
ONE YEAR LIMITED WARRANTY If your Vintage Keeper cooling unit or cabinet fails to perform as designed within one year of the date of purchase, VINTAGE KEEPER INC. warrants that, upon your request, it will be repaired or replaced, at our option, during the one year warranty period. This warranty applies only to the rst end-user purchaser of a Vintage Keeper unit that is purchased and used in the continental United...
Need help?
Do you have a question about the Tuscany 250 and is the answer not in the manual?
Questions and answers