Advertisement
Beforeyou
call for service, review this list. It may save you time and expense. The list includes common
occurrences that are not the result of defective workmanship or materials in this appliance.
Oven Control Beeps
Electronic control has detected a fault condition. Push CANCEL pad to clear the display and stop the
and Displays an "F"
display from beeping. Reprogram the oven. If a fault reoccurs, record the fault number, push the OFF
Error Code
pad and contact an authorized servicer.
Faulty Installation
Place oven rack in center of oven. Place a level on the oven rack. Contact installing agent if rack and
cabinet cutout flooring are not level.
Kitchen cabinet misalignment
may make oven appear to be not level. Be sure cabinets are square and
level. Contact cabinet maker to correct problem.
Entire Oven Does Not
When the oven is first plugged in, or when the power supply to the oven has been interrupted,
the
Operate
display will flash. The oven cannot be programmed
until the clock is set.
Be sure electrical cord is securely
connected
into the electrical junction
box.
Cord/plug
is not installed and/or connected.
Cord is not supplied with oven. Contact your dealer, installing
agent or authorized
servicer.
Service wiring not complete.
Contact your dealer, installing agent or authorized
servicer.
Power outage.
Check house lights to be sure. Call your local electric company.
Short in cord/plug.
Replace cord/plug.
Controls are not set properly. See instructions
to set the controls.
House fuse has blown or circuit breaker
has tripped
immediately
following installation.
House fuse may not be fully engaged.
Check fuse and screw or engage circuit breaker securely.
Oven Light Does Not
Burned-out or loose bulb. Follow the instructions under Oven Light to replace or tighten the bulb.
Work
Self-Cleaning
Cycle
Make sure the oven door is closed.
Does Not Work
Make sure you have removed the oven racks and the oven rack supports
from the oven.
Controls
not set properly. Follow instructions
under "Using the Self-Clean
Feature".
Oven Smokes
Meat too close to the broiler element. Reposition the rack to provide more clearance between the meat
Excessively
During
and the broiler. Preheat broil element for quick searing operation.
Broiling
Meat not properly prepared.
Remove excess fat from meat. Cut remaining
fatty edges to prevent
curling,
but do not cut into the lean.
Grid on broiler pan wrong side-up. Grease does not drain into broiler pan. Always place the grid on the
broiler pan with the ribs up and the slots down to allow grease to drip into the pan.
Broiler pan used without grid or grid cover with aluminum foil. DO NOT use the broiler pan without the
grid or cover the grid with aluminum foil.
Oven needs to be cleaned. Grease has built up on oven surfaces. Regular cleaning is necessary when
broiling frequently. Grease or food spatters cause excessive smoking.
Soil Not Completely
Failure to clean bottom, from top of oven, frame of oven or door area outside oven seal. These areas
Removed
After Self-
are not in the self-cleaning
area,
but get hot enough
to burn on residue.
Clean these areas
before the
Cleaning Cycle is
self-cleaning cycle is started. Burned on residue can be cleaned with a stiff nylon brush and water or a
Completed
nylon scrubber. Be careful not to damage the oven gasket.
Excessive spillovers in oven. Set the self-clean cycle for longer cleaning time.
Poor Baking Results
Many factors affect baking results.
See Baking for hints, causes
and corrections.
See Adjusting
Oven
Temperature.
Flames
Inside
Oven
or
Excessive spillovers
in oven. This is normal, especially
for high oven temperatures,
pie spillovers or for
Smoke from Vent
large amounts of grease on bottom of oven. Wipe up excessive spillovers.
Cooling
Fan Noisy
At high temperature
in the oven, the hi speed cooling fan will start and will cause it to be noisier than
normal, but this is normal function to protect the electronic control.
Advertisement
