Motorola DS6707 Quick Start Manual page 2

DS6707
1
OPTIMUM ARM POSITION
Standard Use
Low/medium/high beep
Power up
Parameter Menu Scanning
High/low/high/low beep
Successful
parameter
setting
DS6707
© 2013 MOTOROLA, INC. All rights reserved.
Motorola reserves the right to make changes to any product to improve reliability, function, or
design. Motorola does not assume any product liability arising out of, or in connection with, the
application or use of any product, circuit, or application described herein. No license is granted,
either expressly or by implication, estoppel, or otherwise under any patent right or patent,
covering or relating to any combination, system, apparatus, machine, material, method, or
process in which Motorola products might be used. An implied license exists only for
equipment, circuits, and subsystems contained in Motorola products.
Warranty
For the complete Motorola hardware product warranty statement, go to:
http://www.motorolasolutions.com/warranty.
For Australia Only
This warranty is given by Motorola Solutions Australia Pty Limited (ABN16 004 742 312) of
Tally Ho Business Park, 10 Wesley Court. Burwood East, Victoria. Our goods come with
guarantees that cannot be excluded under the Australia Consumer Law. You are entitled to
a replacement or refund for a major failure and compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if
the goods fail to be of acceptable quality and the failure does not amount to a major
failure. Motorola Solutions Australia's limited warranty above is in addition to any rights
and remedies you may have under the Australian Consumer Law. If you have any queries,
please call Motorola Solutions Australia at 1800 457 439. You may also visit our website:
http://www.motorola.com/Business/XA-EN/Pages/Contact_Us for the most updated
warranty terms.
Service Information
If you have a problem using the equipment, contact your facility's Technical or Systems Support.
If there is a problem with the equipment, they will contact the Motorola Solutions Global Support
Center at: http://www.motorolasolutions.com/support.
For the latest version of this guide go to: http://www.motorolasolutions.com/support.
Power Supply
Use ONLY a LISTED Motorola, Type no. 50-14000, or PWRS-14000, Direct Plug-In power
supply, marked Class 2 or LPS, or SELV, Rated 5 Vdc, 850 m A Min.
(IEC 60950-1). Use of alternative power supply will invalidate any approvals given
to this device and may be dangerous.
Motorola Solutions, Inc.
One Motorola Plaza Holtsville, New York 11742-1300, USA
MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks
or registered trademarks of Motorola Trademark Holding, LLC and are used under
license. All other trademarks are the property of their respective owners.
© 2011-2013 Motorola Solutions, Inc. All rights reserved.
72-83972-01 Revision D May 2013
DS6707
2
3
1 LED Indicators
2 Scan Window
3 Scan Trigger
AVOID EXTREME WRIST ANGLES
BEEPER INDICATIONS
Short medium beep 4 long low beeps
Bar code decoded
High/low beep Low/high beep
Correct programming
sequence performed
123Scan 2 is an easy-to-use, PC-based software tool that enables rapid and easy customized setup via a bar code or USB
cable. For more information, visit: http://www.motorola.com/123Scan
REGULATORY INFORMATION
Ergonomic Recommendations
Caution: In order to avoid or minimize the potential risk of ergonomic injury follow the
recommendations below. Consult with your local Health & Safety Manager to ensure that you
are adhering to your company's safety programs to prevent employee injury.
• Reduce or eliminate repetitive motion
• Maintain a natural position
• Reduce or eliminate excessive force
• Keep objects that are used frequently within easy reach
• Perform tasks at correct heights
• Reduce or eliminate vibration
• Reduce or eliminate direct pressure
• Provide adjustable workstations
• Provide adequate clearance
• Provide a suitable working environment
• Improve work procedures.
Regulatory Information
This device is approved under Motorola Solutions, Inc. This device is approved under the
Symbol Technologies, Inc. brand: Symbol Technologies, Inc. is a wholly owned subsidiary of
Motorola Solutions, Inc. (collectively "Motorola"). This guide applies to Model Number:
DS6708. All Motorola devices are designed to be compliant with rules and regulations in
locations they are sold and will be labeled as required.
Local language translations are available at the following website:
http://www.motorolasolutions.com/support.
Any changes or modifications to Motorola equipment, not expressly approved by Motorola,
could void the user's authority to operate the equipment.
Radio Frequency Interference Requirements
Tested to comply
with FCC Standards
FOR HOME OR OFFICE USE
frequency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. However there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.
Radio Frequency Interference Requirements – Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada
Marking and European Economic Area (EEA)
Statement of Compliance
Motorola hereby declares that this device is in compliance with all the applicable Directives,
2004/108/EC, 2006/95/EC and 2011/65/EU. A Declaration of Conformity may be obtained from
http://www.motorola.com/doc.
Ukraine
http://www.motorola.com/ds6707
OPTIMUM SCANNING AND IMAGING
0 1 2 3 4 5
0 1 2 3 4 5
AVOID EXTREME
WRIST ANGLES
Off
Transmission error
detected; data is
ignored
Incorrect
programming
sequence or
"Cancel" bar code
scanned
123SCAN
2
Note: This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate radio
Aiming
AVOID BENDING AND REACHING
LED INDICATIONS
Green
Scanner is on Bar code is successfully
and ready to scan, decoded
or no power to
scanner
.
2
Laser Devices
Motorola products using lasers comply with US 21CFR1040.10
and1040.11 except for deviations pursuant to laser notice no.
50, dated June 24, 2007 and IEC 60825-1 (Ed. 2.0),
EN60825-1:2007.
The laser classification is marked on one of the labels on the product.
.
Class 1 Laser devices are not considered to be hazardous when used for their
intended purpose. The following statement is required to comply with US and
international regulations:
Caution: Use of controls, adjustments or performance of procedures other
than those specified herein may result in hazardous laser light exposure.
Class 2 laser scanners use a low power, visible light diode. As with any very bright
light source, such as the sun, the user should avoid staring directly into the light
beam. Momentary exposure to a Class 2 laser is not known to be harmful.
Scanner Labeling
LASER LIGHT- DO NOT STARE INTO
BEAM . CLASS 2 LASER PRODUCT.
LASERSTRAHLUNG - NICHT IN DEN
STRAHL BLICKEN. LASER KLASSE 2.
LUMI»RE LASER - NE PAS REGARDER
DANS LE FAISCEAU. APPAREIL ¿ LASER
DE CLASSE 2 630-680nm, 1mW
Recommended Usage Guide
0 1 2 3 4 5
0 1 2 3 4 5
AVOID BENDING
AVOID REACHING
Alternate left and right hands Alternate left and right hands
taking breaks and task rotation taking breaks and task rotation
recommended recommended
Red
Transmission
error
Local Contact: