Electrolux EI24ID30QW0A Installation Instructions

Dishwasher
CD.808 936 619
Installation Instructions
INSTALLER: Leave Installation Instructions with owner•
OWNER: Read your dishwasher Use and Care Manual. It contains
important safety information for operating this appliance• It also has
many suggestions for getting the best results from your dishwasher•
Read all instructions before installing dishwasher.
For your safety, please read and observe all safety
instructions. This guide will help you anticipate drain, water, and
electrical connections, and help you select the best location for the
dishwasher.
The dishwasher is provided with water heating feature.
The dishwasher is intended for connection to hot water supply.
Tip Over Hazard
Do not use dishwasher until completely installed.
Do not push down on open door.
Failure to follow this warning can result in serious
injury.
Cut Hazard
To prevent serious injury from sharp edges, wear work
gloves when handling, unpacking or disassembling unit.
Parts Included:
%
Tools and Materials Needed for
Installation
(Not Included)
• Drill, Electric
• Driver, Socket 5/32", 1/4", 5/16"
• Flaring Tool / Tube Cutter (for copper tubing)
• Flashlight
• Level
• Pipe Joint Compound (for iron pipe plumbing) or
Pipe Thread Tape (for sealing threads)
• Pliers
• Safety Glasses
• Saw, Keyhole
or 1/2",
11/2" to 2" Hole Cutters
• Screw Drivers, Slotted and a2 Phillips (magnetic tip
preferred)
• Work gloves
• Tape, Electrical or Duct
• Measuring Tape
• Wire Stripper or Utility Knife
• Wrench, Hex-end
• Wrenches, 2 Adjustable (for copper tubing)
or 2 Pipe wrenches (for iron pipe plumbing)
Parts You Will Need*(Not
Included)
• Drain HoseClamp, 1 1/4" (3,1 cm) Diameter
• Brass Elbow, 90 ° with a 3/4" ( Q 2 cm )-11.5 NH to 3/8" ( Q 2 cm )
NPT Compression fitting
• Conduit Connector (UL Listed)
• Wire Nuts, three (3) for 12-14 gauge wire (UL Listed)
"klf required:
• "Y" Branch Tailpiece and
Connector Kit (See Step 8 )
• Air Gap Kit (See Step 8 )
All the parts can be found at local hardware, electrical and
plumbing supply stores•
Electric Shock Hazard
Disconnect electrical power at the fuse box or
circuit breaker box before beginning installation.
Failure to follow this warning could result in death
or serious injury.
®
NOTE: Put unit on its back being careful not to pinch the Water
Drain Hose.
1. Remove two (2) screws at the top the kickplate assembly
2. Tilt and pull forward the kickplate to remove it. - see Figure 1.
NOTE: It is not necessary to remove the outer door for installation•
Figure 1
3. Locate water inlet valve behind kickplate on bottom left underside
of unit. See Figure 4 The valve has a 3/8" ( 1 cm ) NPT male fitting•
4. Connect the 90 ° elbow (not included) to water inlet valve• When
tightened, point elbow should point toward the left. To prevent bending
of bracket or breaking of valve, avoid overtightening.
See Figure 4.
Cabinet Preparation:
As a precaution, it is recommended, but not required that the
cabinets enclosing all sides of the dishwasher (including the
underside of the countertop) be sealed with an oil based paint or
moisture-proof polyurethane to prevent possible steam/moisture
damage.
Electric Shock Hazard
Observe all local codes and ordinances for
electrical and plumbing connections. All electrical
and plumbing work should be performed by
qualified persons. Failure to follow this warning
could result in death or serious injury.
Figure 2
1. Make sure your location has the correct drain, water, and
electrical outlets to make the connections• Do not install unit
under a cooktop range, Damage to tub or other components will
occur.
34"(86,36 cm)
mfn. t o 35¾"
(90,8 cm)
m_x. **
I
24" (60,96cm')
mfn.
Ebctrical, water,
and drain lines
must be confined
to shaded area•
Preferred
Drain Areas
(45,7cm)
cm) max.
standardcabinetrycutout.
/_H_/ (5/16"[0,8cm] min.
clearance 1" (2,5 \
3½" (8,89 cm) min.to _/' ¼" (3,1 cm) required from unit to
4½"(11,43 cm) max. 2¼" underside of c0untert0p.) 2¼"4'_
cm) (5,7 cm)'
_/ 24" (61cm) \
Figure 3
Front Closed
,--23¾"(60,3 cm)_ ,. 24V,"(61,5cm)_
• •
33¾"
(86 ore),
Adjustable
to
35¾"
:_)**
Open Door
501A"(127,6cm)
_,_ 22½"(57,1 cm)÷
l ®
," Open door ]rr
_n_elr _:pplnY/Wate r_
Heightonly adjustable to 35%"(90,8 cm) max when *DIMENSIONS D ONOTINCLUDE I NSULATION-
installedin 35¾" (90,8ore)maxstandard cabinetrycutout. INSULATION BLACKET M AYBECOMPRESSED
to 353,4 " UPON INSTALLATION.
IMPORTANT: For proper operation and appearance of unit,
cabinet opening should have dimensions as shown in Figure 2.
If unit is to be placed in a corner, there must be at least a 2-inch
side clearance between the wall and the open door.
2. Floor shouldbe flat and freeof any obstruction,
IMPORTANT: Drain, water, and electrical lines should be
roughed-in before going any further.
Electric Shock Hazard
Electrical, water, and drain lines must be confined
to shaded areas in Figure 2.
Electric conductors, water, and drain could be
damaged.
Failure to follow these instructions could result in
fire or electric shock.
NOTE: If dishwasher is installed at end of a cabinet, sides and
back must be fully enclosed.
Figure 4
Water line Brass Elbow
(Not Included (Not Included) Electrical Line
Locating the Connections
1. Review dimensions in Figure 2 to locate dishwasher's drain,
water, and electrical connections•
2. All utilities must be routed in shaded area in the Figure 2
Note: Locate the electrical supply and dishwasher's electrical
junction box on right underside of unit behind kickplate
assembly• See Figure 4. Determine where you will connect
to hot water supply. Review Figure 4 and note the location of
water inlet valve• Determine where you will connect the drain
hose.
3. Cut access holes for the Electrical, Water and Drain hoses in the
cabinet within the shaded areas as shown in Figure 2.
4. The dishwasher operates on a 120 volt, 60 Hz electrical supply•
Provide a separate circuit with a fuse or circuit breaker rated for
at least 15 amps (20 amps if connected with disposer) but not
more than 20 amps.
5. Pull electrical cable through hole into installation area.
6. Be sure water inlet valve is protected from freezing• If valve
freezes and ruptures, flooding may occur•
7. Determine amount of tubing needed to connect hot water supply
to the unit's water inlet valve. Extra hose length is necessary
High-pressure and high-temperature Stainless Flexible hose with
a minimum inner diameter of 1/4" may be used. A shut-off valve
installed outside dishwasher cabinet is best.
8. Route water supply line into installation area.
9. Stand dishwasher back upright for further installation•
IMPORTANT: Incoming hot water temperature should be at
least 120°F (49°0). Water pressure should be between 20-90 psi.
Figure 5
NOTE: Install cabinet seal to dishwasher before placing it into
the cabinet
Figure 6
333A,,
Adjustable
to 353A''
®
1. Measure height of cabinet opening from underside of countertop
to floor•
. Move dishwasher to front of installation area.
• Adjust the levelling legs.
Dishwasher Anchoring
4. Choose one of the methods of attachment below to secure unit,
holes need to be pro-drilled using a _5 drill bit regardless of
the option chosen:
a. Side Mount Cabinet Clips (Preferred Method of attachment)
b. Top Mount Cabinet Clips (to be used when Side Mount
is not an available option)
CAUTION: Use extreme care in mounting the dishwasher as to not
scratch, bump or otherwise damage the console or tub.
To install the Side Mounting Clips.
Note: install Side Mount Brackets before unit is installed
into the cabinet, insert screws into the front holes of the
clips only. Use extreme caution when fixing the screws,
not to cratch dishwashers or kitchen cabinet•
(See image below)
(_ To install using Top Mount Cabinet Clips:
Depending on the depth of cabinet, the Top Mount
Clip have a break off point that can be removed if necessary.
NOTE: Install Top Mount Clips before unit is installed into the
cabinet. Screw clips firmly to top brace using screws
provided in the literature pack. (See image below)