Audio Pro WF100 Owner's Manual

PACKING CONTENTS
WF100
TX100 transmitter unit / RX100 receiver unit / USB AC power adaptor
2 x 3.5 mm stereo cable / 1 x Y-cable RCA to 3.5mm stereo
TX100 RX100
TX100 transmitter unit RX100 receiver unit
1 x 3.5 mm stereo cable 1 x 3.5 mm stereo cable
1 x Y-cable RCA to 3.5mm stereo
GENERAL SETUP
Setting up your wireless audio network is real simple. The transmitter and
receiver need power, either through a USB socket or AC adaptor power
supply. RX100 receiver will need the supplied power adaptor for power.
Connect WF100 to any device with audio input or output. Just try your
devices, it will work. You may need to go to a retailer for some additional
cables.
(USB 2.0 input on receivers and other devices is not to recommended to plug RX100 to
as it this may cause noise and interference.)
TRANSMITTER
The TX100 is the transmitter. It sends the audio signal.
Connect to device which you want to play from.
LED lights up blue when wireless connection is
established. LED lights up red when no wireless
connection is established
RECEIVER
The RX100 is the receiver. It receives the audio signal.
Connect to the device you want to listen from.
LED lights up blue when wireless connection is
established. LED lights up red when no wireless
connection is established
HOUSE CODE
With the unique feature of House Codes, you can have up to three transmit-
ters in one house, and as many reciever on each House Code as you want.
Perfect when the household want to listen to different wireless music sources.
MAC SETUP
1. Insert TX100 transmitter to a free USB socket
2. Go to System Preferences, choose Sound under Hardware.
3. Click Output in menu, choose "USB Headset"
Done! You can now send audio from your computer.
PC SETUP
Please do following setup before using music playing software
(for example iTunes or Spotify).
1. Insert TX100 transmitter to a free USB socket.
Wait until software has been installed.
(See lower right hand corner, message window will open when sound device
is ready to use.)
2. Click Start button, go to Control Panel and choose Sound & Sound devices.
3. Under playback of audio, default unit, choose "USB Headset".
Done! You can now send audio from your computer.
POWER SUPPLY
Connect to device
3.5 mm audio jack on side
Use the enclosed AC power adaptor
when no USB power supply is available.
Use cable from RX/TX100 to connect
to your device. TX100 will work on all
To 220V power outlet
computers to send audio without AC
adaptor.
TROUBLESHOOTING
NO WIRELESS CONNECTION:
1. Make sure corresponding House Code is the same on TX100 and RX100.
2. Receiver is out of range from transmitter.
When wireless connection is established on same House Code, LED on both transmitter and
receiver will go blue. If no connection, LED goes red.
WIRELESS CONNECTION, BUT NO SOUND
1. Make sure to choose correct source on receiving device.
2. Check your audio source output is correct on transmitting device.
POWER SUPPLY:
1. Make sure both transmitter and receiver has power supply.
Check all connections and cables.
COMPUTER
- Mac: Make sure you have chosen correct sound output.
See "Mac Setup".
- PC: Make sure you have chosen correct sound output unit.
See "PC Setup".
FEATURES
- Wireless full CD quality sound
- Robust and dedicated network for your audio R Robust and dedicated network for your audio
- Easy setup, get wireless music in seconds
- Wireless range room to room: Up to 20 meters
- Wireless range same room: Up to 50 meters
- Wireless range open field: Up to 100 meters
- No interference or delays
- Time delay max 10ms
- Works with both Mac and Works with both Mac and W PC
- Plug 'n play, no software needed
- Flexible multiroom possibilities
- RF band: 2.4GHz
- Sample rate: 44.1 KHz
- Dedicated proprietary protocol
- USB 2.0 interface
www.audiopro.com
www.audiopro.se
WF100/RX100/TX100
WIRELESS HIFI TRANSMITTER AND RECEIVER
OWNERS MANUAL