INSTRUCTION MANUAL VCC-6572P BEDIENUNGSANLEITUNG MANUEL D’INSTRUCTIONS COLOUR CCD camera CCD-Farbkamera Caméra CCD COULEUR About this manual A propos de ce manuel Before installing and using the camera, please read this Avant d’installer et d’utiliser la caméra, veuillez lire ce manual carefully. Be sure to keep it handy for later reference.
Depending on the conditions of use, installation and environment, FEATURES please be sure to make the appropriate settings and adjustments. If you need help with installation and/or settings, please consult your dealer. • Built-in interline transfer method 1/3" CCD, approx. 470,000 picture elements CONTENTS •...
Disconnect the power greasy smoke or steam, where the dampness may get too high, or cord immediately, and consult your dealer (or a Sanyo Authorized where there is a lot of dust.
PARTS NAMES Video output connector (VIDEO OUT: BNC type) Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector. 12 V DC input terminal (12 V DC, GND) Connect DC connecting cord to the 12V DC input terminal on the camera. Y/C OUT connector Using a coaxial cable (twin type, 75 ohms), connect the Y/C OUT connector from the camera to the S-VIDEO input terminal on the monitor or time lapse VCR.
Page 5
PARTS NAMES Lens mount cap The cap is installed to protect the lens mount section. Remove the lens mount cap before installing a lens (sold separately). Flange-back adjustment screw (FLANGE BACK ADJ.) Flange-back lock screw (FLANGE BACK LOCK) Camera installation bracket The bracket can be fixed at the top or bottom of the camera.
Page 6
PARTS NAMES Lens iris output connector (LENS) This 4-pin connector is used to send the DC control signal and power supply to an auto-iris type lens. Camera setup section (under the cover) These settings are for when using a 1/3 inch CS mount DC (without EE internal amplifier) type lens. However, if due to installation conditions or environment the settings may need to be modified for best results (see "SETTINGS").
ALC and LEVEL volume level controls are available on the lens for iris adjustments. (Set the A.I. LENS switch to the VIDEO position.) Compatible auto-iris lenses 1/3 inch Sanyo DC type lens VIDEO type lens VCL-CS8LY: Standard angle, f= 8 mm...
MOUNTING THE LENS Please use a DC type auto-iris lens (sold separately). Check the lens mount Do not use a lens if the length “ ” is more than mm. That may damage the camera and prevent proper installation. C mount type lens Remove the lens mount cap from the camera.
Page 9
MOUNTING THE LENS Rewiring the lens cable in the lens iris plug Prepare the lens cable. Cut the cable at the plug, then remove approx. 8 mm of the cable sheath and strip about 2 mm from each wire. Install the lens iris plug. Solder the cable to the pins following the correct pin layout (refer to the table and illustrations), then close the plug cover.
CONNECTIONS DC 12 V – (Video signal connections) 12 V DC connection : VIDEO IN Push to insert the cable 12 V DC input : VIDEO OUT Basic connection for monitoring or recording The peripheral devices (VCR, monitor, lens, etc.), and cables are Insert the plug of this power cord into a wall outlet.
Page 11
CONNECTIONS DC 12 V – (Video signal connections) 12 V DC connection : VIDEO IN Push to insert the cable 12 V DC input : VIDEO OUT Connections to the camera Y/C OUT connector The peripheral devices (VCR, monitor, lens, etc.) and cables are The POWER indicator (A) will light.
SETTINGS The illustration shows the factory default settings for the switches in the camera setup section. The camera settings are described on the assumption that a DC type auto iris lens is being used. If you are using a VIDEO type auto iris lens, be sure to read the Note which is given.
Page 13
SETTINGS High speed electronic shutter setting Iris function setting Normally, the speed setting switches for the high speed electronic This should normally be set to the down (AI) position. shutter are all set to the down (OFF) position. This sets the electronic Use a manual or fixed iris lens and set the lens aperture to the shutter speed to 1/50 sec.
Page 14
SETTINGS When using an auto-iris lens (for indoor/outdoor use) Set the switch 4 (IRIS) to the down (AI) position. CAUTION: If conditions are outside the electronic iris operation range or more than the maximum illumination, it will cause saturation of the CCD. In that case, use a manual iris lens.
SETTINGS (MULTI mode: 64 sections) Backlight compensation setting Use an auto-iris lens and set the switch 7 to the up (ON) position, to engage the backlight compensation function. This camera has two different backlight correction functions: multi-spot photometry (MULT) and center focus photometry (CENT). The normal setting (switch 6) is the down (MULT) position, but you can change the switch 6 setting in accordance with the...
SETTINGS White balance adjustment External sync adjustment (VBS) Normally the switch 8 (WB) is set to the down (ATW: auto white Connect the VBS signal output for the other camera to the VBS IN balance) position and the white balance is adjusted automatically. If a connector at the rear of this camera.
If it still does not perform correctly, If using a DC type auto-iris lens, you will need to set the LEVEL please consult your dealer or a Sanyo Authorized Service Centre. (VR301) volume when shooting in the conditions described below.
Servicing should always be referred to your dealer or Iris function : Manual EI/AI switching Sanyo Authorized Service Centre. Electronic iris range : 1.0 lux to 50,000 lux (F 1.2 lens) Electronic shutter : 8 speeds, selectable by switches: (1/50, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000 sec.)
Page 19
SPECIFICATIONS Dimensions 1/4”–20 UNC 12.6 22.4 Features and specifications are subject to change without prior notice or obligations. English...