1. Manuals
  2. Brands
  3. Voxx Manuals
  4. Car Alarm
  5. ELITE911
  6. Installation instructions manual

Voxx ELITE911 Installation Instructions Manual

Vehicle security system
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Installation Instructions
PROFESSIONAL INSTALLATION
STRONGLY RECOMMENDED
Installation Precautions:
Technical Support
For Authorized Dealers - (800) 421-3209
Hours: 8:00 a.m. - 7:00 p.m. EST Monday thru Friday
This device complies with part 15 of the FCC rules and with RSS-210 of the
industry Canada. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Roll down window to avoid locking
keys in vehicle during installation
Avoid mounting components or
routing wires near hot surfaces
Avoid mounting components or
routing wires near moving parts
Tape or loom wires under hood for
protection and appearance
Use grommets when routing wires
through metal surfaces
Use a voltmeter for testing and
verifying circuits
10:00 a.m. - 2:00 p.m. EST Saturday
Y10 / Y11
INS0883
Rev. A
11/98

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ELITE911 and is the answer not in the manual?

Questions and answers

Related Manuals for Voxx ELITE911

Summary of Contents for Voxx ELITE911

  • Page 1 Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or routing wires near hot surfaces Avoid mounting components or routing wires near moving parts Tape or loom wires under hood for protection and appearance Use grommets when routing wires through metal surfaces...

  • Page 2: System Layout

    System Layout FUSED +12V SOURCE SIREN OR BLACK HORN OUTPUT (-) ORANGE PARKING LIGHT OUTPUT (+) ORANGE/BLACK VIOLET ILL. ENTRY / ARMED OUTPUT (-) (Y-11 ONLY) STARTER KEY WHITE RED STARTER MOTOR WHITE TRUNK RELEASE (-) (Y-11 ONLY) +12 VOLTS CHASSIS GROUND BLACK (-) LOCK / (+) UNLOCK...

  • Page 3: Installation

    1. Installation A. Siren / Horn (ORANGE on 3-Pin Connector) Make appropriate connections below. Siren • Mount bell housing downwards. • Use at least two (2) screws to secure siren to mounting location. • Connect siren BLACK wire to module ORANGE wire. •...
  • Page 4 1. Installation E. Starter Interrupt • WHITE/RED -Starter Key Side • WHITE - Starter Motor Side • Connect to vehicle starter wire at ignition switch harness. Circuit Verification - Target wire registers voltage only when ignition key is turned to the START position. Circuit Verification after starter wire is cut: •...
  • Page 5 1. Installation Diagram 3 I. Parking Lights (ORANGE/BLACK Wire on 3-Pin Connector) • Circuit Verification - Refer to Vehicle Wire Color and Location Chart for circuit type and location, or verify the vehicle wire using the following guideline: • Positive Systems - Target wire registers voltage when parking lights are on. •...
  • Page 6 1. Installation Connections Type 1 Type 2 Type 3 Type 4 Type 5 Other See specifications in Dia. 7 Door Locks Vehicle Wire Color / Dia. 5 Dia. 6 Dia. 8 Dia. 9 Location Guide or call Technical Support Diagram 5 GREEN/BLACK - LOCK (+) BLUE/BLACK - UNLOCK (+) Type 1 - Positive 3-Wire Door Lock System...
  • Page 7 1. Installation K. Power Door Locks (cont.) Diagram 8 BLUE/BLACK - LOCK(-) Module Wires GREEN/BLACK - UNLOCK(-) Factory Vacuum Cut Here Pump Type 4 - Vacuum Door Lock System Note: Turning on option 8, the Long Locks feature, in program- mable options is required with this type of locks.

  • Page 8: System Power-Up

    1. Installation M. Shock Sensor (Optional on some systems) • Using supplied tie wrap, mount the shock sensor to the steering column or a sturdy brace or wire harness. • Plug the impact detector onto the 4-pin module connector. Note: Some shock sensors may already be attached to the harness. N.

  • Page 9: Programming Remote Transmitters

    Programming Remote Transmitters Note: The Y-11 has four “slots”, or memory locations, to store remote transmitter codes, giving it the ability to operate from up to four remote transmitters. The Y-10 has two slots. For proper operation, a transmitter code must be stored into each memory slot.

  • Page 10: Programming Selectable Options

    3. Programming Selectable Options Note: You can go into option programming mode without exiting the transmitter learn mode. To do so, do not turn the ignition key off or close the doors at the end of the transmitter programming section and proceed directly to step 2 below. Enter the transmitter programming mode as indicated above.

  • Page 11: Testing The Alarm System

    Testing the Alarm System Arming and Disarming Close all doors and press ARM on remote • All doors lock transmitter. • Siren chirps two times / parking lights flash • Status indicator flashes steadily Press Disarm on remote transmitter. • All doors unlock •...

Table of Contents