Oleo-Mac BC 22 TR Operator's Instruction Manual
  1. Manuals
  2. Brands
  3. Oleo-Mac Manuals
  4. Lawn and Garden Equipment
  5. BC 22 TR
  6. Operator's instruction manual
Oleo-Mac BC 22 TR Operator's Instruction Manual

Oleo-Mac BC 22 TR Operator's Instruction Manual

Hide thumbs Also See for BC 22 TR:
Table of Contents

Advertisement

Quick Links

Download this manual
Model not available for EU markets
BC 22 TR
(21.7 cm
)
3
OPERATOR'S INSTRUCTION BOOK

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BC 22 TR and is the answer not in the manual?

Questions and answers

Related Manuals for Oleo-Mac BC 22 TR

Summary of Contents for Oleo-Mac BC 22 TR

  • Page 1 Model not available for EU markets BC 22 TR (21.7 cm OPERATOR’S INSTRUCTION BOOK...

  • Page 5: Table Of Contents

    TRANSLATION OF ORIGINAL INSTRUCTIONS 9. M A I N T E N A N C E ( a l l i n fo r m a t i o n required to keep the machine at peak efficiency) INTRODUCTION 10. STORAGE For correct use of the machine and to avoid 11.
  • Page 6 in good conditions. In case of damage or WARNING: National regulations may limit deterioration, immediately substitute them the use of the machine. (Fig. 18). 15 - Do not utilize the machine for uses 1 - Do not operate the machine unless you different from the ones specified in the have received specific instruction on its use.

  • Page 7: Symbols And Safety Warnings

    5. STARTING 2. SYMBOLS AND SAFETY WARNINGS (Fig.25) 1 - Read operator’s instruction book before operating this machine. 2 - Wear head, eye and ear protection. 3 - Wear strong boots and gloves when cutting FUELING with metal or plastic blades. 4 - Be aware that objects can be thrown.
  • Page 8 We strongly recommend the use of 2% (1:50) CAUTIONS – Alkylate fuels have Oleo-Mac two cycle engine oil, which is different density than normal fuel. Therefore specifically formulated for all Oleo-Mac air- engines, set with normal fuel, need different cooled two-stroke engines.
  • Page 9 appear in the fingers, hands or wrists. stable position. Check that the head is free. Holding the brush cutter down (Fig.3), pull Before starting the engine, make sure that the the starter rope until the first kick over of the throttle lever works freely.

  • Page 10: Stopping The Engine

    NOTE: It is normal for smoke to be emitted • Do not cut from a ladder, this is extremely from a new engine during and after first use. dangerous. • Stop the engine before setting the brush 6. STOPPING THE ENGINE cutter down.
  • Page 11 WARNING: Do not use the machine WARNING: Never use the machine without a guard or with a defective guard. unless you are able to call for help in the Never use the machine without the event of an accident. transmission shaft. 2.

  • Page 12: Transporting

    longer and to reduce the wear on the trimmer head. Cutting • The trimmer is ideal for cutting grass that is difficult to reach using a normal lawn mower. Keep the cord parallel to the ground when cutting. Avoid pressing the trimmer head against the ground as this can ruin the lawn and damage the tool.

  • Page 13: Maintenance Chart

    9. MAINTENANCE Maintenance Chart Please note that the following maintenance intervals apply for normal operating conditions only. If your daily work requires longer than normal or harsh cutting conditions are present, then the suggested intervals should be shortened accordingly. Inspect (Leaks, Cracks, and Wear) Complete Machine Clean after finishing daily work Controls (STOP button, Choke Lever, Throttle...
  • Page 14 NYLON LINE HEAD fuel filling hole. Replace it (Fig. 15) if too dirty. Only use line of the same diameter as the original ENGINE to avoid overloading the engine (Fig. 18). In order to get more line out of the cutting head, Clean cylinder fins with a brush or compressed tap it lightly on the ground while working.

  • Page 15: Storage

    11. ENVIRONMENTAL PROTECTION WARNING: Weather conditions and Environmental protection should be a priority of altitude may affect carburation. considerable importance when using the machine, for the benefit of both social cohesion EXTRA MAINTANANCE ADVISABLE and the environment in which we live. It is advisable to inspect the machine by a - Try not to cause any disturbance to the specialized technician at an authorized service...

  • Page 16: Technical Data (A Summary Of The Main Specifications Of The Machine)

    12. TECHNICAL DATA BC 22 TR Displacement 21.7 Engine 2 stroke EMAK Power 3000 Min. rpm Maximum speed of output 8.500 spindle Engine speed at maximum 11.900 output spindle speed Fuel tank capacity 400 (0.40 l) Primer carburetor Antivibration system...
  • Page 17 BC 22 TR Pressure level dB (A) 95.0 EN 11806 EN 22868 Uncertainty dB (A) 2000/14/EC Measured sound power level EN 22868 dB (A) 109.0 EN ISO 3744 Uncertainty dB (A) Guaranteed sound power level 2000/14/EC dB (A) 111.0 EN 22868...

  • Page 18: Declaration Of Conformity

    Guaranteed sound power level: 112.0 dB (A) 2. Brand Oleo-Mac, Type BC 22 TR Technical Documentation deposited with Administrative 3. Serial ID 930 XXX 0001 ÷ 930 XXX 9999 (BC 22 TR) Headquarters: Technical Department conforms to the requirements of Directives:...

  • Page 19: Troubleshooting (Helps You To Quickly Solve Any Problems You May En- Counter While Using The Machine)

    15. TROUBLESHOOTING WARNING: always stop the machine and remove the key before carrying out any of the corrective checks recommended in the table below, except when they require the unit to be in operation. When all the possible causes have been checked and the problem is not resolved, consult an Authorised Service Centre.
  • Page 20 WARNING! – This owner’s manual must stay with the machine for all its life. It’s an EMAK S.p.A. trademark 42011 Bagnolo in Piano (RE) Italy Tel. +39 0522 956611 • Fax +39 0522 951555 service@emak.it • www.oleomac.it...

Table of Contents

Save PDF