Table of Contents
Related Manuals for Patton SmartLink M-ATA
Summary of Contents for Patton SmartLink M-ATA
- Page 1 SmartLink M-ATA Micro-Analog Telephone Adapter User Manual Sales Office: +1 (301) 975-1000 Technical Support: +1 (301) 975-1007 E-mail: support@patton.com WWW: www.patton.com Part Number: 07MSLMATA-GS, Rev. E Revised: November 26, 2014...
- Page 2 Under no condition shall Patton Electronics be liable for any damages incurred by the use of this product. These damages include, but are not limited to, the following: lost profits, lost savings and incidental or consequential damages arising from the use of or inability to use this product.
-
Page 3: Summary Table Of Contents
19 3 Home................................22 Network—LAN ..............................26 Telephony ................................. 34 6 System................................52 Documentation ..............................73 8 Logout................................75 Contacting Patton for assistance......................... 77 Compliance information ........................... 82 Specifications ..............................86 Dial plans ................................. 96 Calling Features ..............................99 Voice prompt configuration .......................... -
Page 4: Table Of Contents
............................16 General observations document....................16 Typographical conventions used in this ............................16 General conventions General information ............................17 ..........................18 SmartLink M-ATA overview SmartLink installation............................19 ............................20 Installing the M-ATA ......................21 Resetting the M-ATA to factory default 3 Home................................22 ...............................23 System information ...............................23... - Page 5 SmartLink M-ATA Getting Started Guide Table of Contents ..............................27 Enabled ...............................27 Service ............................27 Interface Status ............................27 Network Settings ..........................27 Dynamic IP Assignment ..............................28 IP address ............................28 MAC address .............................28 Subnet Mask ............................28 Default Gateway ............................28 Domain name .............................28 DNS address ............................28...
- Page 6 SmartLink M-ATA Getting Started Guide Table of Contents ............................37 Phone Line Status ............................37 Registration Status ..............................38 User Name ............................38 Caller ID Setting ...........................38 Subscribed for Voicemail ............................38 Messages waiting ..................................39 ............................39 SIP Configuration ............................39 SIP Server Settings ............................40 Gateway Settings ............................40...
- Page 7 SmartLink M-ATA Getting Started Guide Table of Contents ..............................46 Password ........................46 Supplementary Service Activation ............................46 Call Forward All ..........................46 Selective Call Forward ..........................46 Three-Way Conferencing ..........................46 Incoming Call Block ............................46 Distinctive Ring .............................46 Call Transfer ..........................47 Dialing by IP Address ..............................47...
- Page 8 SmartLink M-ATA Getting Started Guide Table of Contents ............................55 Web Page Protect ............................55 New Root Password ............................55 New User Password ...........................55 Confirm new password ............................55 Saving your work Configuration................................56 ..............................56 Syslog Service ............................56 Enable Syslog .............................56 Syslog Server ............................57 Debug Service ............................57...
- Page 9 SmartLink M-ATA Getting Started Guide Table of Contents ............................64 Income Caller ID ..........................64 Self Caller ID Block ............................64 Calling Prefix Keys ...............................64 Call Return ..............................64 Warm Line ..............................65 Speed Dial ............................65 Call Forward All ..............................65 IP Dialing ..............................65 Call Hold ........................65...
- Page 10 77 ................................78 Introduction Contact information..............................79 ......................79 Patton support headquarters in the USA ............79 Alternate Patton support for Europe, Middle East, and Africa (EMEA) Warranty Service and Returned Merchandise Authorizations (RMAs)..............80 ............................80 Warranty coverage ..........................80 Out-of-warranty service ............................80 Returns for credit ..........................80...
- Page 11 SmartLink M-ATA Getting Started Guide Table of Contents .................................93 Management ............................94 Operating Environment ...................................95 System Dial plans ................................. 96 ................................97 Introduction Sample Dial Plans..............................98 .............................98 Simple Dial Plan ..........................98 Non-dialed Line Dial Plan ............................98 Complex Dial Plan Calling Features ..............................99 ................................100...
-
Page 12: List Of Figures
SmartLink M-ATA installation diagram ........ -
Page 13: List Of Tables
List of Tables General conventions ..............16 Bellcore standard ring cadence patterns . -
Page 14: About This Guide
99 describes the calling features that can be accessed from phones attached to the SmartLink M-ATA • Appendix E on page 101 explains how to configure the voice prompt function in the SmartLink M-ATA For best results, read the contents of this guide before you install the M-ATA. -
Page 15: Precautions
WARNING Safety when working with electricity The SmartLink contains no user serviceable parts. The equip- ment shall be returned to Patton Electronics for repairs, or repaired by qualified service personnel. WARNING The external power adapter shall be a listed Limited Power Source. -
Page 16: General Observations
SmartLink M-ATA User Manual Do not work on the system or connect or disconnect cables during periods of lightning activity. WARNING In accordance with the requirements of council directive 2002/96/ EC on Waste of Electrical and Electronic Equipment (WEEE), ensure that at end-of-life you separate this product from other waste and scrap and deliver to the WEEE collection system in your country for recycling. -
Page 17: General Information
Chapter 1 General information Chapter contents ..........................18 SmartLink M-ATA overview... -
Page 18: Smartlink M-Ata Overview
LAN and Internet connections like xDSL and cable modems. Figure 1. SmartLink M-ATA The SmartLink M-ATA provides one RJ-45 Ethernet port and one FXS (RJ-11) analog phone port. Side panel LEDs quickly show at-a-glance the status of the system, WAN and phone ports. -
Page 19: Smartlink Installation
Chapter 2 SmartLink installation Chapter contents ............................20 Installing the M-ATA ....................21 Resetting the M-ATA to factory default... -
Page 20: Installing The M-Ata
Plug in the telephone (see figure 2). Plug in the PC or LAN, or a LAN hub/switch. Plug the power adapter into the power jack on the SmartLink M-ATA (see figure 2). Connect the other end of the power cord to an appropriate AC power outlet. -
Page 21: Resetting The M-Ata To Factory Default
SmartLink M-ATA User Manual 2 • SmartLink installation Resetting the M-ATA to factory default The M-ATA should be powered off. Press the recessed button on the rear of the M-ATA, then apply power to the unit. Continue depressing the button while the LEDS are flashing, and only release the button after the LEDs have stopped. -
Page 22: Home
Chapter 3 Home Chapter contents ............................22 System information .............................22 System Uptime ............................22 LAN IP Address ..............................22 MAC address ............................22 Application Version ..............................22 Config Date ................................23 Security ...........................23 Application Code Version ..........................23 Downloader Code Version ...............................23 System Status ............................23 SIP Messages Sent ..........................23 SIP Messages Received ...............................23... -
Page 23: System Information
LAN IP Address The IP address of the SmartLink M-ATA. If (Static) is shown next to the address, it means the IP address was assigned to the SmartLink M-ATA under the LAN Settings. (Dynamic) indicates the IP address was learned via DHCP. -
Page 24: Security
SmartLink M-ATA User Manual 3 • Home Security Indicates that the SmartLink web interface utility has been secured with a password. To configure a password, see section “Set Security Password” on page 55. Application Code Version Shows the application code version being used. -
Page 25: System Status
SmartLink M-ATA User Manual 3 • Home System Status Shows VoIP statistics for the period of time since the SmartLink M-ATA was last reloaded (either by powering the unit off and then on again, or by selecting System > Reload). SIP Messages Sent Total number of VoIP SIP messages sent (including retransmissions). -
Page 26: Network-Lan
Chapter 4 Network—LAN Chapter contents ..................................25 Status .............................25 Interface Status ..............................25 Enabled ..............................25 Service ............................25 Interface Status ............................25 Network Settings ........................25 Dynamic IP Assignment ..............................26 IP address ............................26 MAC address ............................26 Subnet Mask .............................26 Default Gateway ............................26 Domain name ............................26 DNS address ...........................26 DynDNS address... -
Page 27: Status
SmartLink M-ATA User Manual 4 • Network—LAN Status Shows the status of key LAN network settings as configured under LAN settings Interface Status Figure 4. Internet Status window Enabled indicates the LAN interface is enabled and ready to be used. -
Page 28: Ip Address
Refers to the address of your domain name server that was defined under LAN settings or that was learned dynamically through DHCP. DynDNS address The IP address of the dynamic DNS server that will be notified when the SmartLink M-ATA’s dynamic IP address changes. VLAN... -
Page 29: Settings
• IP address. • IP of the netmask. • IP of the gateway. • IP of the DNS Server, if applicable. • Host name (the name will identify the computer on the Internet, such as SL4020.patton.com). Settings... -
Page 30: Wan Pppoe Configuration
4 • Network—LAN • Domain name (the name that will identify one or more IP addresses). For example, the patton.com domain is used by Patton Electronics Company. That domain can include multiple hostnames (such as SL4020.patton.com, ftp.patton.com, and so on) that point to individual computers on the Patton network. In short, for the hostname URL http://www.patton.com, the domain name is patton.com. -
Page 31: Configuring Dynamic Dns
If blank, the LAN interfaces will use the hardware value of MAC VLAN Configuration The SmartLink M-ATA can mark outgoing Ethernet frames on the LAN interface with VLAN and priority tags. Other devices on the LAN can use the tags to control how frames from the SmartLink M-ATA are pro- Settings... -
Page 32: Vlan Tag (Ieee 802.1Q)
SmartLink M-ATA User Manual 4 • Network—LAN cessed. All data leaving the SmartLink M-ATA will be marked with the specific value unless overridden on the telephony VLAN configuration settings. Figure 9. VLAN Configuration section of the Settings window VLAN Tag (IEEE 802.1q) IEEE 802.1q Ethernet VLAN tag for all outgoing packets on LAN Ethernet interface. -
Page 33: Tos/Diffserv
SmartLink M-ATA User Manual 4 • Network—LAN ToS/DiffServ This sub-page is used to configure the Type-of-Service/Diffserv byte values which are to be used in the IP header of all transmitted SIP signaling packets and RTP packets. The ToS/DiffServ byte values are entered as two-digit hexadecimal values. -
Page 34: Telephony
Chapter 5 Telephony Chapter contents VoIP Status ................................37 VoIP Server Registration Status ........................37 Current Server ............................37 Domain ..............................37 Base RTP Port ............................37 Phone Line Status ............................37 Registration Status ............................ 37 User Name ..............................38 Caller ID Setting ............................38 Subscribed for Voicemail ...........................38 Messages waiting ............................38 SIP ..................................39 SIP Configuration............................ - Page 35 SmartLink M-ATA User Manual 5 • Telephony Packetization ..............................43 Jitter Buffer ..............................43 FAX without T.38 (Use G.711 fax) ........................43 Saving your work ............................44 Phone 1 ................................45 User Information ............................45 Phone Number ............................45 User Name ..............................45 Port................................45 CallerID Name ............................46 Password ..............................
- Page 36 SmartLink M-ATA User Manual 5 • Telephony HTTP Digest Setting ............................50 Saving your work ............................50 Speed Dial ................................51 Line 1 Speed Dial Settings ..........................51 Speed Dial Serv ............................51 Speed Dial 1–8 Phone Number/IP Dialing ....................51 Saving your work ............................51...
-
Page 37: Voip Status
• Online—The phone line is online, registered with the SIP server and ready to send and receive phone calls using the SIP server. • Registering—The SmartLink M-ATA is in the process of registering with the VoIP server. VoIP Status... -
Page 38: User Name
SmartLink M-ATA User Manual 5 • Telephony • No Registration—The SmartLink M-ATA is not attempting to register with the SIP server because “Send Registration Request” is not checked on SIP sever setting screen. • Error: Not Authorized—A SIP final status message status of 401 or 407 has been received from the SIP server. -
Page 39: Sip
SIP Server Settings The SmartLink M-ATA will automatically attempt to locate the VoIP server by using the domain name speci- fied in the LAN interface or the server will be discovered via DHCP on the WAN interface. When found, the discovered server will be listed as the Current Server. -
Page 40: Gateway Settings
SmartLink M-ATA User Manual 5 • Telephony • Send SUBSCRIBE—If checked, the SmartLink will send a SIP subscribe to the server specified. This box must be checked for the voicemail message counted and message waiting notification to work. • SUBSCRIBE Server IP or FQDN—The IP address or fully qualified domain name of the subscription service. -
Page 41: Rtp Telephone Event Configuration
SmartLink M-ATA User Manual 5 • Telephony RTP Telephone Event Configuration This sub-page allows configuration of the out-of-band signaling options for SIP. Select whether OOB tele- phone event signaling is to be done using the SIP INFO message, or to be done via RFC2833 RTP signaling. -
Page 42: Sip T4
SmartLink M-ATA User Manual 5 • Telephony RFC 3261 T4 value (maximum duration a message will remain in the network). Range: 0–64 seconds SIP T4. (default is 5000 msec or 5 seconds). RTP Parameters RTP Port Min and RTP Port Max define a range that contains at least four even-numbered ports (100–106, for example). -
Page 43: Audio/Codec Configuration
SmartLink M-ATA User Manual 5 • Telephony Audio/CODEC Configuration Figure 19. Audio/CODEC Configuration window CODECS • Selected column: Check the codecs that are acceptable to use • Silence Suppression column: Specifies whether silence suppression should be turned on in the SmartLink 4020. -
Page 44: Saving Your Work
SmartLink M-ATA User Manual 5 • Telephony The selection of T.38 or G.711 fax pass-through for fax transmissions originated from the SL4020 will be determined by the receiving fax device. T.38 is enabled by default. To disable T.38, go to Telephony > CODECS and select FAX without T.38 (Use G.711 fax) (see figure 19 page 43). -
Page 45: Phone 1
SmartLink M-ATA User Manual 5 • Telephony Phone 1 Phone 1 window contains the following sections: • User Information (see figure 20) • Supplementary Service Settings (see figure 21 on page 46) • Dial Out Type (see figure 22 on page 48) •... -
Page 46: Callerid Name
SmartLink M-ATA User Manual 5 • Telephony CallerID Name Enter the caller ID name. Password Enter the password. Supplementary Service Activation These settings enable or disable each of following calling features. Most features can also be enabled or disabled by using the telephone handset (see section “Supplementary Service Keys”... -
Page 47: Dialing By Ip Address
SmartLink M-ATA User Manual 5 • Telephony Dialing by IP Address Enable IP dialing service—This service allows user IP addresses to be used to make calls. Speed Dial Enable speed dial service. Message Waiting Indicator Enable MWI service—The message-waiting indicator (MWI) is a common feature of telephone networks and uses an audible indication (such as a special dial tone) to indicate that a voice mail message is waiting. -
Page 48: Dial Out Type
SmartLink M-ATA User Manual 5 • Telephony Dial Out Type Figure 22. Dial Out Type section of Phone 1 window Dial Out Type Enable Hot-Line and Warm-Line services. To achieve this, one sequence in the dial plan must start with a pause, with a 0 delay for a Hot Line, and a non-zero delay for a Warm Line. -
Page 49: Selective Call Forward Settings
SmartLink M-ATA User Manual 5 • Telephony Selective Call Forward Settings Figure 24. Selective Call Forward Settings section of Phone 1 window Incoming caller #1–8 Up to 8 incoming calls can be selected for call forwarding. Forward destination #1–8 Up to 8 destinations to which incoming calls can be forwarded. -
Page 50: Http Digest Setting
SmartLink M-ATA User Manual 5 • Telephony HTTP Digest Setting SIP INVITE must contain a valid Authorization header that is based on an Auth ID and a password using MD5 digest algorithm. The Auth ID must be specified in the username parameter in the Authorization header. -
Page 51: Speed Dial
SmartLink M-ATA User Manual 5 • Telephony Speed Dial Figure 28. Speed Dial window Line 1 Speed Dial Settings Speed Dial Serv Enable Speed Dial Service. Speed Dial 1–8 Phone Number/IP Dialing Target 1–8 phone number (or URL) assigned to speed dial. -
Page 52: System
Chapter 6 System Chapter contents ............................51 Set Security Password ............................51 Web Page Protect .............................51 New Root Password ............................51 New User Password ..........................51 Confirm new password ............................51 Saving your work ..............................52 Configuration ..............................52 Syslog Service ............................52 Enable Syslog ............................52 Syslog Server ............................53 Debug Service ............................53... - Page 53 SmartLink M-ATA User Manual 6 • System ........................58 Block Anonymous Calls ............................58 Distinctive Ring ..............................58 Warm Line ............................59 Do Not Disturb ..............................59 IP Dialing ............................59 Speed Dialing ...........................59 Income Caller ID ..........................59 Self Caller ID Block ............................59 Calling Prefix Keys ..............................59...
- Page 54 SmartLink M-ATA User Manual 6 • System .........................64 SNMP Trap Configuration ..............................64 IP address ............................64 Trap Community ......................64 SNMP Community Configuration ...........................64 Read Community ..........................64 Write Community ........................64 SNMP System Configuration ..........................64 System Description ............................64 System Object Id ............................64 Saving your work ..............................65...
-
Page 55: Set Security Password
SmartLink M-ATA User Manual 6 • System Set Security Password Figure 29. Set Security Password window Two levels of system configuration are available: user level and system level. Access to each level is password controlled. Web Page Protect Enable or disable web access protection. When set to YES, a password will be required to access the SmartLink M-ATA web configuration interface. -
Page 56: Configuration
SmartLink M-ATA User Manual 6 • System Configuration Figure 30. Configuration window Syslog Service Enable Syslog Enable or disable system logging. During normal operations, Syslog should be turned off. A sample Syslog record of a complete call is shown below. -
Page 57: Debug Service
07-07-2005 14:48:51 Local7.Debug 10.10.22.13 **EndPoint State: StateOnHook ==> StateOffHook in src/common/fxs/OnHookFxs.c: 55 Debug Connection Port The port number of the debug server to be used for receiving debug messages from the SmartLink M-ATA. Use port 412 to send debug output to a syslog server. NTP Service The network time protocol (NTP) synchronizes timekeeping among a set of distributed time servers and cli- ents. -
Page 58: Ntp Server
SmartLink M-ATA User Manual 6 • System NTP Server Specify the IP address of the NTP server. Time Zone Select the GMT time zone for your location. For help in determining the time zone, go to the UTC/GMT Con- version website at http://www.dxing.com/utcgmt.htm. -
Page 59: Service Access
Enable Ping Reply When checked, the SmartLink M-ATA will reply to ping requests received on the WAN port. If the option is not checked, the SmartLink M-ATA will not respond to ping requests received on the WAN port. -
Page 60: Localization
SmartLink M-ATA User Manual 6 • System Localization Localization window contains the following sections: • Call Progress Tones (see figure 32 on page 61) • Distinctive Ring Setting (see figure 33 on page 62) • Supplementary Service Keys (see figure 34 on page 63) •... -
Page 61: Dial Tone
SmartLink M-ATA User Manual 6 • System To specify a 350-Hz and 480-Hz tone that will be played at 15 dB for one second and then pause for 0.5 sec- onds, you would specify: 350@-15+480@-15#ON(1000),OFF(500),R The following example would repeat playing of a tone of 280 Hz at -8 dBm for 0.3 seconds with a pause of 0.1 second and a tone of 550 Hz for 0.8 seconds with a pause of 0.15 seconds. -
Page 62: Distinctive Ring Settings
SmartLink M-ATA User Manual 6 • System Distinctive Ring Settings The SmartLink M-ATA Distinctive Ring Settings window (see figure 33) enables you to specify up to 8 sets of distinctive ring cadences. Figure 33. Distinctive Ring Setting section of Localization window The following is a sample ring cadence pattern configuration: ... -
Page 63: Supplementary Service Keys
Supplementary Service Keys Supplementary Service Keys are key sequences that can enable and disable certain calling features from an analog phone handset attached to the SmartLink M-ATA. Note The supplementary service keys must begin with a ‘*’,’#’ character, or f (flash hook) and follow a 1 or 2 numeric digit(s). -
Page 64: Do Not Disturb
SmartLink M-ATA User Manual 6 • System Do Not Disturb Enables or disables the do not disturb feature. IP Dialing Enables or disables dialing by IP address. Speed Dialing Enables or disables the speed dialing feature. Income Caller ID Enables or disables the display of incoming caller ID feature. -
Page 65: Speed Dial
SmartLink M-ATA User Manual 6 • System Speed Dial Configures speed dialing keys. To configure speed dialing numbers enter the calling prefix key (*71 is the fac- tory default), the speed dial key, the number to dial and then on hook the phone. You will hear a second dial tone after entering the calling prefix key. -
Page 66: Voicemail Access
Minimum on-hook time before off-hook to qualify as hookflash. At less than this value, the on-hook event is ignored. SIP Session Timer value The amount of time the SmartLink M-ATA will wait during an active call to send repeated re-invites on active calls to allow the SIP server to determine the status of a call. Localization... -
Page 67: Conditional Call Forwarding Timer
Warm Line Delay Specify a time period as a delay time for warm line dialing. If warm line is enabled, then the SmartLink M-ATA will wait this amount of time after the handset is off-hook before dialing the warm line phone number. -
Page 68: Ring Setting
SmartLink M-ATA User Manual 6 • System Ring Setting Figure 38. Ring Setting section of Localization window Ring Waveform Specify the ring tone waveform. Ring Frequency Specify the ring tone frequency. Ring Voltage Specify the ring tone voltage. FXS Port Polarity Configuration Figure 39. -
Page 69: Snmp Configuration
SmartLink M-ATA User Manual 6 • System SNMP Configuration Figure 40. SNMP Configuration window SNMP Trap Configuration IP address Trap host IP address. Trap Community public The community name used by the SNMP manager to verify traps. The default value is... -
Page 70: Auto Upgrade
Figure 41. AutoUpgrade window Routine Upgrade every xxx day(s) If selected, the SmartLink M-ATA will check for automatically check for updates at system reload time and on a periodic basis based on the number of days selected. Enable Auto Upgrade Enable or disable auto upgrade—If enabled, the SmartLink M-ATA will automatically check the upgrade... -
Page 71: Manual Upgrade
ROM file download and permanent write of the application to the device’s flash memory. During download of new firmware images, the LEDs on the SmartLink M-ATA will flash sequentially. Typically, HTTP downloads take about 5–10 minutes. After the download is completed, the download status page will be displayed. -
Page 72: Reload
SmartLink M-ATA User Manual 6 • System Reload Figure 43. Reload window Reloading the system will terminate all network connections and restart your browser connection. CAUTION Reload and execute Main Application Chose the option, for execution of the main application which you have configure, once you reload the system. -
Page 73: Documentation
Chapter 7 Documentation Chapter contents ................................69 Introduction... -
Page 74: Introduction
7 • Documentation Introduction Documentation Clicking the link (see figure 44) connects to the Patton website to display the most current ver- sion of the SmartLink M-ATA Getting Started Guide in portable document format (PDF). Figure 44. Documentation link Introduction... -
Page 75: Logout
Chapter 8 Logout Chapter contents ................................71 Introduction... -
Page 76: Introduction
SmartLink M-ATA User Manual 8 • Logout Introduction Logout Clicking (see figure 45) displays Logout—Sure to Logout?. If you want to exit from the SmartLink management utility, click the Logout button (see figure 45). Figure 45. Logout window You will be returned to the password verification page (see figure 46). -
Page 77: Contacting Patton For Assistance
Chapter contents ................................73 Introduction ............................73 Contact information ....................73 Patton support headquarters in the USA ..........73 Alternate Patton support for Europe, Middle East, and Africa (EMEA) ............73 Warranty Service and Returned Merchandise Authorizations (RMAs) ............................74 Warranty coverage .........................74 Out-of-warranty service ...........................74 Returns for credit ..........................74... -
Page 78: Introduction
9 • Contacting Patton for assistance Introduction This chapter contains the following information: • “Contact information”—describes how to contact Patton technical support for assistance. • “Warranty Service and Returned Merchandise Authorizations (RMAs)”—contains information about the RAS warranty and obtaining a return merchandise authorization (RMA). -
Page 79: Contact Information
9 • Contacting Patton for assistance Contact information Patton Electronics offers a wide array of free technical services. If you have questions about any of our other products we recommend you begin your search for answers by using our technical knowledge base. Here, we have gathered together many of the more commonly asked questions and compiled them into a searchable database to help you quickly solve your problems. -
Page 80: Warranty Service And Returned Merchandise Authorizations (Rmas)
If you have ordered the wrong equipment or you are dissatisfied in any way, please contact us to request an RMA number to accept your return. Patton is not responsible for equipment returned without a Return Authorization. - Page 81 9 • Contacting Patton for assistance 7622 Rickenbacker Dr. Gaithersburg, MD 20879-4773 USA Patton will ship the equipment back to you in the same manner you ship it to us. Patton will pay the return shipping costs. Warranty Service and Returned Merchandise Authorizations (RMAs)
-
Page 82: A Compliance Information
Appendix A Compliance information Chapter contents .................................76 Compliance ............................76 EMC Compliance: ............................76 Safety Compliance ......................76 Radio and TV Interference (FCC Part 15) ......................76 CE Notice (Declarations of Conformity) -
Page 83: Compliance
SmartLink M-ATA User Manual A • Compliance information Compliance EMC Compliance: FCC Part 15, Class B EN55022, Class B EN55024 Safety Compliance EN60950-1 Compliance... -
Page 84: Radio And Tv Interference (Fcc Part 15)
SmartLink M-ATA User Manual A • Compliance information Radio and TV Interference (FCC Part 15) This equipment generates and uses radio frequency energy, and if not installed and used properly—that is, in strict accordance with the manufacturer's instructions—may cause interference to radio and television recep- tion. -
Page 85: Ce Notice (Declarations Of Conformity)
SmartLink M-ATA User Manual A • Compliance information CE Notice (Declarations of Conformity) We certify that the apparatus identified in this document conforms to the requirements of Council Directive 1999/5/EC on the approximation of the laws of the member states relating to Radio and Telecommunication Terminal Equipment and the mutual recognition of their conformity. -
Page 86: Specifications
Appendix B Specifications Chapter contents .............................78 Voice Connectivity ................................78 Connectivity ......................78 Voice Processing (signalling dependent) ...........................78 Fax and Modem Support ............................79 Voice Services/Features ................................79 IP Services ...............................79 Management .............................79 Operating Environment ..................................79 System... -
Page 87: Voice Connectivity
SmartLink M-ATA User Manual B • Specifications Voice Connectivity 2-wire Loopstart, RJ-11/12 Short haul loop 1.1 km @3REN Caller-ID Type-1 FSK and ITU V.23/Bell 202 generation Voice Connectivity... -
Page 88: Connectivity
SmartLink M-ATA User Manual B • Specifications Connectivity 1 10/100 Full Duplex/Autosensing Ethernet RJ-45 Connectivity... -
Page 89: Voice Processing (Signalling Dependent)
SmartLink M-ATA User Manual B • Specifications Voice Processing (signalling dependent) MGCP • Packet Cable NCS 1.0 • IETF MGCP 1.0 Voice codes • G.711 A-Law/μ-Law (64 kbps) • G.726 (ADPCM 40, 32, 24, 16 kbps) • G.723.1 (5.3 or 6.3 kbps) •... -
Page 90: Fax And Modem Support
SmartLink M-ATA User Manual B • Specifications Fax and Modem Support G.711 transparent FAX T.38 Fax relay (9.6 k, 14.4 k) Fax and Modem Support... -
Page 91: Voice Services/Features
SmartLink M-ATA User Manual B • Specifications Voice Services/Features Call forwarding Call transfer Call hold Call waiting 3-way calling Voice Services/Features... -
Page 92: Ip Services
SmartLink M-ATA User Manual B • Specifications IP Services IPv4 M-ATA; RIPv1, v2 (RFC 1058 and 2453) IP filtering NAPT DHCP client & server PPPoE ICMP redirect (RFC 792); Packet fragmentation DiffServe/ToS set or queue per header bits IP Services... -
Page 93: Management
SmartLink M-ATA User Manual B • Specifications Management Browser configuration interface Voice prompt configuration TFTP configuration & firmware loading SNMP v2 agent (MIB II and private MIB) Management... -
Page 94: Operating Environment
SmartLink M-ATA User Manual B • Specifications Operating Environment Operating temperature: 0–40°C (32–104°F) Operating humidity: 5–80% (non condensing) Operating Environment... -
Page 95: System
SmartLink M-ATA User Manual B • Specifications System Power: 100–240 VAC (50/60 Hz) System... -
Page 96: C Dial Plans
Appendix C Dial plans Chapter contents ................................81 Introduction ...............................81 Sample Dial Plans ............................81 Simple Dial Plan ..........................81 Non-dialed Line Dial Plan ............................81 Complex Dial Plan... -
Page 97: Introduction
SmartLink M-ATA User Manual C • Dial plans Introduction The MGCP and SIP code will allow provisioning (via web browser) of the dial plan. A dial plan gives the unit a map to determine when a complete number has been entered and should be passed to the SIP server or gate- keeper for resolution into a destination IP address. -
Page 98: Sample Dial Plans
SmartLink M-ATA User Manual C • Dial plans Sample Dial Plans Simple Dial Plan Allows dialing of 7-digit numbers (e.g. 5551234) or an operator on 0. Dial plan is (0T|xxxxxxx) Non-dialed Line Dial Plan As soon as handset is lifted the unit contacts the gatekeeper (used for systems where DTMF detection is done in-call). -
Page 99: Calling Features
Appendix D Calling Features Chapter contents ................................84 Introduction... -
Page 100: Introduction
SmartLink M-ATA User Manual D • Calling Features Introduction The SmartLink M-ATA family supports advanced calling features that can be turned on and off from phones attached to the SmartLink M-ATA (see table 3). Note Your telephony service provider must enable your service for these calling features to work. -
Page 101: Voice Prompt Configuration
Appendix E Voice prompt configuration Chapter contents ................................86 Introduction .........................86 Accessing the voice prompt ......................86 Existing voice prompt configuration... -
Page 102: Introduction
SmartLink M-ATA User Manual E • Voice prompt configuration Introduction The M-ATA provides the ability to review and set the network configuration parameters using the handset of an attached analog telephone handset. By default from the factory, DHCP is enabled and an IP address is not configured.