Advertisement
Quick Links
Table of Contents
Congratulations on purchasing your new
Hunter® ceiling fan! It will provide comfort
and performance in your home or office for
many years. This installation and operation
manual contains complete instructions for
installing and operating your fan.
We are proud of our work and appreciate
the opportunity to supply you with the best
ceiling fan available anywhere in the world.
To register your fan, please visit:
www.HunterFan.com/register
Save your receipt for proof of purchase.
What to Expect with
Your Installation
Tools Needed
30 inches
7 feet
2
Downrod
6
Light Kit
Remote Control
13
1
M0037-01 • 02/04/15 • © 2015 Hunter Fan Company
Mounting Options
Ladder
3
Wiring
Canopy
9
Operation,
Maintenance & Cleaning
15
www.HunterFan.com
1.888.830.1326
Ceiling Bracket
4
5
Blades
11
12
Troubleshooting
?
?
?
16
18
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Hunter M0037-01
Summary of Contents for Hunter M0037-01
- Page 1 Downrod Wiring Canopy Blades To register your fan, please visit: www.HunterFan.com/register Save your receipt for proof of purchase. Operation, Light Kit Remote Control Maintenance & Cleaning Troubleshooting M0037-01 • 02/04/15 • © 2015 Hunter Fan Company...
- Page 2 Assess ceiling angle Select a downrod length harmful interference to radio communications. M0037-01 • 02/04/15 • © 2015 Hunter Fan Company...
- Page 3 Tools Needed www.HunterFan.com 1.888.830.1326 Pliers Wire Strippers Screwdrivers Ladder Power Drill 9/64” Drill Bit (optional) (optional) If mounting to a support structure, you will also need these tools. M0037-01 • 02/04/15 • © 2015 Hunter Fan Company...
- Page 4 You need BOTH You need ONLY a Longer a Longer Downrod & Downrod an Angled Mounting Kit *most common M0037-01 • 02/04/15 • © 2015 Hunter Fan Company M0037-01 • 02/04/15 • © 2015 Hunter Fan Company...
- Page 5 To avoid possible electrical shock, before 1-888-830-1326. installing your fan, disconnect the power by turning off the circuit breakers to the outlet Refer to warning w.1 on pg. 2 box associated with the wall switch location. M0037-01 • 02/04/15 • © 2015 Hunter Fan Company...
- Page 6 Steps 1-5 to remove standard downrod pipe Longer Downrod for angled ceilings or ceilings 10’ or higher Shorter Downrod for fans installed close to ceiling Steps 6-10 to reassemble with new pipe M0037-01 • 02/04/15 • © 2015 Hunter Fan Company...
- Page 7 4-5 full turns) until it stops. with pliers. DO NOT can be inserted. from the top of the downrod. HAND TIGHTEN. 8” 3/8” If the setscrew is not tightened securely, the fan may fall. M0037-01 • 02/04/15 • © 2015 Hunter Fan Company...
- Page 8 Put the wires and downrod through the canopy. Let the canopy sit loosely on top CANOPY OR WIRES. Place the downrod of the fan. ball into the slot in the ceiling bracket. M0037-01 • 02/04/15 • © 2015 Hunter Fan Company...
- Page 9 Spread the wires apart, with the grounded wires on one side of Refer to CAUTION c.1 on pg. 2 the outlet box and the ungrounded wires on the other side of the outlet box. M0037-01 • 02/04/15 • © 2015 Hunter Fan Company...
- Page 10 Spread the wires apart, with the grounded wires on one side of Refer to CAUTION c.1 on pg. 2 the outlet box and the ungrounded wires on the other side of the outlet box. M0037-01 • 02/04/15 • © 2015 Hunter Fan Company...
- Page 11 Insert the two canopy screws lifted into place, the canopy fits into the screw holes are aligned. found in the hardware bag. the hanging bracket as shown. Note: Fan style may vary. M0037-01 • 02/04/15 • © 2015 Hunter Fan Company...
- Page 12 Your blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust. For cleaning the fan, use soft brushes or cloths to prevent scratching. Cleaning agents may damage the finishes. M0037-01 • 02/04/15 • © 2015 Hunter Fan Company...
- Page 13 Go to www.HunterFan.com/FAQs and click the upper switch housing. Failure to properly secure all three switch housing screws could result in the light fixture falling. “How do I install my fan without the light kit?” M0037-01 • 02/04/15 • © 2015 Hunter Fan Company...
-
Page 14: Operation Instructions
Exceeding the wattage limit marked on the MAX wattage sticker affixed to the light socket(s) may result in fire hazard or improper operation. M0037-01 • 02/04/15 • © 2015 Hunter Fan Company... - Page 15 Fan OFF button and the Fan ON button for four seconds to pair the remote. To prevent faulty operation, please disconnect power from all other ceiling fans within range while pairing. M0037-01 • 02/04/15 • © 2015 Hunter Fan Company...
- Page 16 To change the fan speed, slowly pull the fan pull-chain switch to select the desired speed. Light Operation: Press and quickly release the ON or OFF button on the remote control to turn the light OFF or ON. M0037-01 • 02/04/15 • © 2015 Hunter Fan Company...
- Page 17 Carefully remove the globe. Unscrew bulbs and replace with bulbs of same type and wattage. Reinstall the globe assembly. For questions regarding removing a light kit, call customer service 1-888-830-1326. M0037-01 • 02/04/15 • © 2015 Hunter Fan Company...
- Page 18 Transmitter only works when and click “How do I properly install held at close range multiple remote-controlled fans?” • Change battery. for information on how to correct this issue. M0037-01 • 02/04/15 • © 2015 Hunter Fan Company...
Need help?
Do you have a question about the M0037-01 and is the answer not in the manual?
Questions and answers