Hookup Diagrams - Mackie M-2000 Owner's Manual

Hookup Diagrams

OPTIONAL CONNECTION USING BINDING POSTS
M-Series Power Amplifier: Stereo Mode Connection
Ch 1 and 2 on single
4-conductor
speaker cable
1+/–
2+/–
CHANNEL 1
COLD
SPEAKER
AMPLIFIER
END
END
1–
1–
HOT
1+
2+ 1+
2+
2–
2–
COLD
CHANNEL 2
M-Series Power Amplifier: Biamp Connection Using Built-in X-over
TO SPEAKERS
SPEAKER OUTPUTS
+
BRIDGE
+ +
SPEAKER OUTPUTS
+
CAUTION BRIDGE
LETHAL
VOLTAGES AMP
+ +
MAY APPEAR MODE
AT OUTPUT
TERMINALS. STEREO
CLASS 3 WIRING
IS REQUIRED.
MONO
HPF
1300W / CH
BRIDGE
4Ω LOAD MIN
LPF
2600W BRIDGE
8Ω LOAD MIN
FULL
PIN 1 = CH1 PIN 1 = BRIDGE PIN 1 = CH2
PIN 2 = CH2 PIN 2 = UNUSED PIN 2 = UNUSED 150Hz
X-OVER
1 2
BRIDGE
ON/
TYPICAL
OFF
LIMIT
AMP MODE SWITCH
Passive Speakers (Mackie S408)
FROM MIXING CONSOLE
SPEAKER OUTPUTS
+
CAUTION
BRIDGE
LETHAL
VOLTAGES AMP
+ +
MAY APPEAR MODE
AT OUTPUT
TERMINALS.
CLASS 3 WIRING
IS REQUIRED.
1300W / CH
4Ω LOAD MIN
2600W BRIDGE
8Ω LOAD MIN
PIN 1 = CH1 PIN 1 = BRIDGE PIN 1 = CH2
PIN 2 = CH2 PIN 2 = UNUSED PIN 2 = UNUSED
1 2
BRIDGE
AMP MODE SWITCH
STEREO
Biampable Two-Way Speaker
FROM MIXING CONSOLE
LEFT AND RIGHT MAIN OUT
.
M
HIGH EFFICIENCY POWER AMPLIFIER
AC LINE
BREAKER
SERIAL / DATE CODE
(PUSH TO RESET)
HPF
LPF
FULL
150Hz
X-OVER C A U T I ON
RISK OF ELECTRIC SHOCK • DO NOT OPEN
ON/
TYPICAL
DESIGNED BY MACKOIDS IN WOODINVILLE, WA, USA
OFF MANUFACTURED IN CHINA • FABRIQUE EN CHINE
©2005 LOUD TECHNOLOGIES INC. • "MACKIE" AND
LIMIT
THE "RUNNING MAN" FIGURE ARE REGISTERED
~120VAC 60Hz 1600W
TRADEMARKS OF LOUD TECHNOLOGIES INC.
STEREO
This drawing shows a typical stereo hookup, connecting
two speakers to the Speakon® outputs. The Amp Mode
switch is set to STEREO, and the X-over switches are set
to FULL. The binding posts can also be used to connect
the speakers (shown as an optional connection).
MAIN OUT
HIGH EFFICIENCY POWER AMPLIFIER
SERIAL / DATE CODE
STEREO
MONO
HPF HPF
BRIDGE
LPF LPF
FULL FULL
150Hz 150Hz
X-OVER X-OVER C A U TI ON
RISK OF ELECTRIC SHOCK • DO NOT OPEN
ON/ ON/
TYPICAL TYPICAL
DESIGNED BY MACKOIDS IN WOODINVILLE, WA, USA
OFF OFF MANUFACTURED IN CHINA • FABRIQUE EN CHINE
©2005 LOUD TECHNOLOGIES INC. • "MACKIE" AND
LIMIT LIMIT
THE "RUNNING MAN" FIGURE ARE REGISTERED
TRADEMARKS OF LOUD TECHNOLOGIES INC.
The Channel 1 Speakon output connector
has four conductors and carries both
channels (1± is Channel 1 out and 2± is
X-OVER SWITCHES
Channel 2 out). This is ideal for driving
CH 1: LPF CH 2: HPF
a biampable two-way speaker cabinet.
The Amp mode switch is set to STEREO,
Channel 1's input is jumpered over to Channel 2 using
the Thru connector on Channel 1. The X-over switch on
Channel 1 is set to LPF while Channel 2 is set to HPF.
Channel 1 carries the low frequencies (below 150 Hz) to
the low-frequency driver, and Channel 2 carries the high
frequencies (above 150 Hz) to the high-frequency driver.
Many biampable cabinets are configured to accept both
LF and HF signals on a single Speakon connector.
4000
.
M 4000
AC LINE
BREAKER
(PUSH TO RESET)
~120VAC 60Hz 1600W
Owner's Manual
7