Advertisement
AM4060
Integrated Mixer/Amplifier
Architects' and Engineers' Specifications
The integrated mixer/amplifier shall have a nominal out-
put power of at least 60W RMS. It shall operate on 115VAC or
230VAC at either 50Hz or 60Hz and have its source power
supplied by a detachable IEC power cord. In addition the unit
shall be capable of being directly powered by a 24Vdc
source, such as storage batteries. It shall have a power
switch on the front panel. The unit shall have a constant-
impedance output to drive a 4Ω load at its rated output. It
shall also have 25V, 50V, 70V and 100V constant-voltage out-
puts with like performance.
Inputs to the unit shall include: at least four actively bal-
anced microphone; two unbalanced, stereo Aux; and an
unbalanced signal processing return. Outputs shall include:
at least two unbalanced Tape (auxiliary) jacks with a com-
mon, continuously variable level control; and one signal pro-
cessing send. Balanced connections shall be made through
XLR connectors and unbalanced connections through RCA
connectors.
Microphone Input 1 shall have adjustable sensitivity
between mic and line, selected by a switch on the rear panel.
This input shall also be programmable to completely exclude
or attenuate all other inputs when its priority link is activated
by either a contact closure or a VOX circuit, with a continu-
ously adjustable threshold. The XLR connector for Input 1
shall be wired, in parallel, to a barrier strip on the rear panel.
Microphone inputs 2-4 shall have a 24V phantom powering
circuit that can be disabled with a switch on the rear panel.
These inputs shall be equipped with a high-pass filter and a
low-pass filter having a response of 12dB/octave and fixed
–3db points at 300Hz and 7kHz, respectively. Each of these
filters shall be enabled by a switch on the rear panel.
Additionally, these inputs shall be programmable to com-
pletely exclude or attenuate all other inputs except for micro-
phone input.
Two auxiliary voltage outputs shall be provided on the
rear panel to drive accessory relays and LEDs. The relay out-
put shall deliver +18Vdc at 300mA. Voltage shall go high
when any microphone priority function is active.
The unit shall have, on its front panel, continuously vari-
able controls for each microphone input, an auxiliary input
selector switch, a master volume control, as well as bass and
treble shelving filter controls. The shelving filters shall have a
range of ±12dB, with the frequency for the bass fixed at
www.mackieindustrial.com
16220 Wood-Red Rd. NE, Woodinville, WA 98072 USA
888.337.7404, fax 425.487.4337, industrial@mackie.com
UK
+44.1268.571.212, fax +44.1268.570.809, info@rcf-uk.com
+39.0522.354.111, fax +39.0522.926.208, industrial@rcf.it
ITALY
FRANCE
+33.3.8546.9160, fax +33.3.8546.9161, rcf.commercial@wanadoo.fr
GERMANY
+49.2572.96042.0, fax +49.2572.96042.10, industrial@mackie.de
100Hz and the treble fixed at 10kHz. LED status indicators
shall be provided on the front panel to indicate power, signal
present at the output terminals, peak signals near clipping
and an overload condition.
The integrated mixer/amplifier shall be a model AM4060,
manufactured by Mackie Industrial.
Electronic files for this product available at:
www.mackieindustrial.com
This Specification Sheet
Quick-Start Manual
Owner/Operator's Manual
Mackie Designs continually engages in research related to product improvement. New material, produc-
tion methods, and design refinements are introduced into existing products without notice as a routine
expression of that philosophy. For this reason, any current Mackie Industrial product may differ in some
respect from its published description, but will always equal or exceed the original design specifications
unless otherwise stated. ©1999-2001 Mackie Designs Inc. All rights Reserved.
registered trademarks of Mackie Designs Inc. Mackie Industrial is a trademark of Mackie Designs Inc.
AM4060.PDF
AM4060QS.PDF
AM4060ML.PDF
and
are
part no. 910-139-10 Rev.B
4
O F 4 P A G E S
oF 6 PAGES
Advertisement
