Table of Contents
Advertisement
SYSTEM INSTALLATION
Pin4: Blue/Black: Unlock #30 Common (Output)
Pin5: Brown/Black: Unlock #87 Normally Open (Input)
Pin6: Violet/Black: Lock #87a Normally Closed
Pin7: Green/Black: Lock #30 Common (Output)
Pin8: White/Black: Lock #87 Normally Open (Input)
Pin9: Red: Constant +12V Input. Connect this wire to the battery or Constant Power wire at the Ignition
Switch with a 15Amp Supply.
Pin10: Black: System Ground. Connect this wire firmly to the Chassis Ground.
6-pin Secondary Harness for Outputs(H2)
Pin 1: ORANGE WIRE: Armed Output (-) 500mA. The orange wire supplies a ground output while armed
to activate a relay for starter defeat and anti-grind protection.
Pin 2: BLUE WIRE: Second unlock (passenger unlock)output (-) 200mA This system is equipped with a
dedicated passenger unlock output allowing two stage door lock operation. When connected this wire,
disarming the system will unlock only the driver s door. Pressing the disarm button again will unlock all doors..
Pin 3: WHITE/BLACK WIRE: Auxiliary Channel 5 Output (-) 200mA. This wire provides a (-) 200mA
output whenever the transmitter button
is pressed for 2S. This output can be programmed to provide the follo
wing types of outputs:
a.0.8-second timed: Output that will send a ground pulse of 0.8 second.
b.15-second timed: Output that will send a ground continuous pulse for 15 seconds.
c.Latched,reset with ignition: Output that will send a signal when the Channel 5 button (button
will continue until the same button (button
) is pressed again. It additionally stops output whenever the ignition
is turned on.
Pin 4: PURPLE/BLACK WIRE: Auxiliary 4 Output (-)500mA for windows rolling-up option. Connect to
a power window module.
Pin 5: BLACK/WHITE WIRE: Dome Light Output (-) 500mA. Connect to the wire that activate the vehicle's
dome light, usually the door pin switch wire. Note: the dome light output can usually connect to the same wire
used for the door trigger input (see purple and green door input wire).
Note: This output is only intended to drive a relay. It can not be connected directly to the dome light
circuit, as the output cannot support the current draw of one or more light bulbs.
Never use this wire to drive anything but a relay or a low-current input. The transistorized output
can only supply 200mA of current. Connecting directly to a solenoid, motor, or other high-current
device will cause it to fail.
Pin 6: RED/WHITE WIRE: Vehicle Trunk Release Wire (-)500mA. Connect this wire to the electronic
trunk opener. (Relay may required).
8-pin 2510 Harness for Inputs and Outputs(H3)
Pin 1: GREEN/BLACK WIRE: Factory Disarm Output (-) 500mA. This wire provides a ground output on
disarming and before remote starting to disarm a factory security system. Connect to the wire that requires a
ground pulse to disarm the factory security system.
Pin 2: GREEN/WHITE WIRE: Factory Rearm Output (-) 500mA. This wire supplies a ground output on
remote start shutdown to rearm a factory security system. Connect to the wire that requires a ground pulse to
rearm the factory security system.
Pin 3: BLACK WIRE: Optional Sensor Input (-).Connect to an optional instant sensor such as trunk pin switch.
Turbo/Short Run
Park the vehicle and set parking brake.
Remove your foot from the brake pedal
and leave the engine running.
Three chirps from the Horn
Exit and secure the vehicle.
Press button
for 0.5s to
arm and lock the car.
Note: Once you activate the short-run turbo mode, the system will remain this mode always. If you don t
) is pressed and
want this mode any more, press button
Remote Start Timer Mode
In arming state
Parking
four times
1.In this mode, the system will start the engine every 3 hours, for a maximum of six cycles. The engine will
run for the programmed run time and then shut down to keep engine warm in the cold weather.
2.The remote start command
timer mode.
3.To exit timer mode, press button
brake pedal or press button
4.If any other shut down zones or alarm has been triggered, the timer mode will cancel.
FEATURES DESCRIPTION
Parking lights flash three times
Turn off the ignition key,
the engine will keep running.
The engine will turn off after
the programmed run time.
+
again to cancel it anytime.
Press button
for 0.5s.
The system will enter
Remote Start Timer Mode
+
can shut down the engine in timer mode, but the system will remain in the
0.5s to disarm the system, turn the ignition key on and then press the
0.5s and then button
0.5s again.
OFF
Turn on
Four
Flashing slowly
Hide quick links:
Advertisement
Table of Contents
