Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Navnet Manuals
  4. IP Camera
  5. TZT9/14/BB TZ touch
  6. Settings manual

Navnet TZT9/14/BB TZ touch Settings Manual

Axis ip camera (h.264) settings
Hide thumbs

Advertisement

Quick Links

Download this manual
TZT9/14/BB
Model:
Axis IP Camera (H.264)
Settings
1

Advertisement

loading

Summary of Contents for Navnet TZT9/14/BB TZ touch

  • Page 1 TZT9/14/BB Model: Axis IP Camera (H.264) Settings...

  • Page 2: Table Of Contents

    INDEX 1. Introduction – v3.01 with H.264 2. Overview 2-1. Summary – Setup Procedure 2-2. Latest Axis Cameras Compatible with H.264 Format 2-3. Tested Axis Video Servers at FEC 3. Setting up a PC 4. Setting up Axis IP Camera 4-1.

  • Page 3: Overview

    1. Introduction – v3.01 with H.264 In addition to MPEG-4, the TZtouch v3.01 software is also compatible with H.264 format, which offers a wider selection of cameras from Axis Communications AB. Native H.264 formatted images occupy a great amount of bandwidth for the TZT9/14/BB Ethernet network.

  • Page 4: 2-2. Latest Axis Cameras Compatible With H.264 Format

    2-2. Latest Axis Cameras Compatible with H.264 Format To find the latest Axis camera models using the H.264 format, visit the Axis product selector on their website: <http://www.axis.com/products/video/selector/index.php>. 2-3. Tested Axis Video Servers at FEC The following Axis video servers were used for tests at Furuno Electric Company, in Japan. M7014 http://www.axis.com/products/cam_m7014/index.htm Analog Input: Four (4) channels...
  • Page 5 3. Setting up a PC This section describes how to assign a dedicated IP address to a PC. In this example, a Windows 7 PC is used. 1. Access [Start] – [Control Panel]. 2. Open [Network and Sharing Center]. 3. Open [Change adapter settings].
  • Page 6 Note: It can take up to 20 seconds for the new IP to be recognized. A popup window on the bottom right corner should show when the IP is correctly set. Turn OFF any Firewall that could prevent data to be exchanged between NavNet and...

  • Page 7: Setting Up Axis Ip Camera

    4. Setting up Axis IP Camera 4-1. Setting up IP Address of Axis IP Cameras To work with NavNet TZtouch, Axis IP cameras need to be set up with specific IP Addresses. Up to four (4) IP cameras can be connected to a TZtouch network.
  • Page 8 4. Install the AXIS IP Utility program on your PC. 5. Double-click on [AXIS IP Utility] to open the program. The following window will open, showing the detected cameras in the network. Note: If you use the same camera models in multiple locations, be sure to write down the serial numbers of each camera, along with their intended location, to help correctly assign the IP camera’s name.
  • Page 9 8. Verify the IP address was successfully updated. 9. Repeat this process with all of the other camera(s). 10. After the IP addresses have been changed, restart the cameras (power OFF/ON). 4-2. Configuring Axis IP Camera Axis IP cameras must be configured using a Web browser. 1.
  • Page 10 : “root” Password : “pass” Note: When the webpage loads, pay attention to the top of the page to authorize the installation of the ActiveX®. Click on the yellow bar and choose “Install ActiveX”. (ActiveX is a registered trademark of Microsoft Corporation) 4.
  • Page 11 [Compression] to [30] and click on [Save]. In this example, [640x480 (4:3)] is selected as the resolution, because this is the maximum resolution supported by the M1011. Tips: For cameras supporting a higher resolution than the M1011, such as the M5013, be sure to set the [Resolution] [800x600 (4:3)].
  • Page 12 Note: It is recommended to zoom in on the image to have a better “Home” preset. When the view is correctly set up, type “Home” for the Current position and select [Use current position Home]. Click on [Add] to validate. If you do not need the camera to return to the “Home”...

  • Page 13: Setting Up Axis Video Server

    5-1. Setting up IP Address of Axis Video Servers To work with NavNet TZtouch, an Axis video server must be set up with specific IP Addresses. Up to two (2) video servers can be connected to the TZtouch network. In this example, the Axis M7014 is used.
  • Page 14 5-2. Configuring Axis Video Server As with Axis IP cameras, Axis video servers must also be configured using a Web browser. 1. Enter the IP address of the video server. In this example, “http://172.31.200.7” is entered. 2. When the camera configuration page opens, click on [Setup] to access the configuration page. 3.
  • Page 15 6. In [Basic Setup] – [3 Date & Time], select [Synchronize with computer time] and click on [Save]. 7. In [Basic Setup] – [4 Video Stream] – [Video 1] to [Video 4] and [Quad Stream] – [Image] tab, select [Aspect ratio correction], set [Resolution] to [4CIF (640 x...

  • Page 16: Showing Camera Images

    8. In [Basic Setup] – [4 Video Stream] – [Video 1] to [Video 4] and [Quad Stream] – [H.264] tab, set as follows. 6. Showing Camera Images This section describes how to show camera images on the TZT9/14/BB. 6-1. Checking Axis IP Camera(s) in Menu 1.
  • Page 17 6-2. Checking Axis Video Server(s) in Menu 1. After the interconnection and setup of video servers is complete, confirm they are detected in the TZtouch network by accessing [Menu] – [Camera] – [Axis Quad Server] and [Second Axis Quad Server]. Detected Disconnected or Not Detected By default, [Server] is set to [OFF].

  • Page 18: Tips – 4 X Ip Cameras + 2 X Video Servers

    7. Tips – 4 x IP Cameras + 2 x Video Servers A maximum of four (4) sets of IP cameras and two (2) sets of video servers are available in one TZtouch network. In this example, the following items are configured and networked with the TZT14. Items Models IP Addresses...
  • Page 19 Note: A maximum of two (2) screens can be allocated to the Camera view in the 3-split screen mode on a TZtouch MFD. Select one of these sources in each screen. --- END ---...