Sharp MX-FX11 Service Manual page 27

SW Bit
Item
No. No.
121 1, 2 Not used
3 Print Staple setting
4, 5 Print Staple position
6 Not used
7, 8 Print Selection of delivered
sheet size
122 1 Transmission Polling protection
2-8 Not used
123 1-8 Not used
-
127
128 1-3 Not used
4 Internet FAX Setting of the internet
FAX mail content
(Footer)
5 Internet FAX Internet FAX coding
system priority
selection
(Coding system for
manual input)
(Coding system for
one-touch registration)
6 Internet FAX Processing at times of
mail reception (when
the Content-X-
CIAJWNETFAX field is
not yet received)
7 Internet FAX Setting of reduced
printing when receiving
A3 by Internet FAX
8 Internet FAX Setting of reduced
printing when receiving
letters by Internet FAX
SW selection and function
Set to determine whether or not to staple when outputting received FAX data.
"0": No
"1": Yes
With the finisher attached, set the staple position for when conducting stable
output of FAX printed data.
"00": Rear 1 point
"01": Front 1 point
"10": Center 2 points
"11": Same action as initial value
When "Bottom one position" is set, "parallel" and "Slant" are selected with
SW90-6.
Sheet size setting when conducting stable output of FAX/Internet FAX printed
data with the finisher attached.
"00": A4 or A3 (8.5 x 11 or 11 x 17)
"01": B5 or B4 (8.5 x 11 or 8.5 x 14)
"10": A4 (8.5 x 11)
"11": A4R (8.5 x 11R)
Set to determine whether or not to execute protection when the other party
requests polling.
"0": Protect
"1": Do not protect
When the protection setting is selected and a request for polling is received
from the other party's machine, bulletin board transmission is conducted if the
source number of the other party coincides with the number permitted for
polling.
When the setting not to protect is selected, bulletin board transmission is
executed regardless of the source number of the other party.
Setting to determine whether the mail footer registered from the web is added
to the content or not in sending the internet FAX.
"0": The footer is not added.
"1": The footer is added.
The standard compression system for sending operation of internet FAX can be
set.
"0": MH (G3)
"1": MMR (G4)
* The compression system for address registration is fixed to "MH (G3)" and is
not linked with this item.
This item is linked with the system setting, the FAX, the image send setting, the
internet FAX setting, and "the standard compression system setting" of the
internet FAX initial setting.
Setting to determine whether or not to print the mail text in cases where there is
no "CONtent-X-CIAJWNETFAX" in the mail field when mail is received by
Internet FAX.
"0": Do not print mail letters
"1": Print the main text of mails
Exclude confirmed sent mails
Setting to determine whether or not to print reduced to 11 x 17 inch sheet size
when receiving A3 width documents when 11 x 17 inch size sheet is set in
Internet FAX reception.
"0": Reduce
"1": Do not reduce (discard)
When not reducing, the area that cannot be printed is scrapped.
Reduce the overall document to 94% when conducting reduced printing.
Setting to determine whether or not to print reduced to A4 size sheet when
receiving 8.5 x 11 (letter) size documents when A4 size sheet is set in Internet
FAX reception.
"0": Reduce
"1": Do not reduce (discard)
Reduce the overall document to 94% when conducting reduced printing.
MX-FX11 FAX SOFTWARE SWITCH 2 – 23
System settings
Device setting
Device setting
FAX reception
setting
Polling protection
setting
Internet FAX initial
setting
Internet FAX initial
setting
Internet FAX
reception setting
Internet FAX
reception setting
Internet FAX
reception setting