CONTENTS PAGE o Safety Instructions o Technical Specifications o Remote Control o Preperations o Operating Your TV o Block Diagram o IC Specs o Pin Voltages of IC’s o OSCILLOSGRAPHS OF SOME IC PINS o Electrical Adjustments o Channel Frequency Tables o Spare Part List...
SAFETY INSTRUCTIONS GENERAL GUIDELINES the receiver, such as screw heads, aerials, 1. It is advised to insert an isolation transformer connectors, control shafts etc. When the in the AC supply before servicing a hot exposed metallic part a return path to the chassis.
AND MULTIMETER (SELECT VDC) AND THEN SHORT CIRCUIT DIRECTLY TO DISCHARGE COMPLETELY TECHNICAL SPECIFICATIONS Power source: 220-240V AC, 50-60Hz Power consumption (nom.) : 40 W 14” 50 W 20”, 21” Standby power consumption : Aerial impedance : 75Ohm, coaxial type Receiving system PAL BG PAL SECAM BG...
REMOTE CONTROL 1. MUTE button 2. Ten key program button 3. Two digit program button (-/--) 4. MENU button 5. Program up button 6. Volume decrease button 7. Return to selected programme button (SWAP) 8. Information button (i) 9. STAND-BY button 10.
Page 6
PREPARATIONS MAIN SUPPLY CONNECTIONS Connect the TV mains plug into your domestic mains socket outlet (230 V 50Hz AC). Press the Program up, Program down button or Numeric Buttons on the remote handset to switch the TV on. AERIAL CONNECTION Using a 75Ω...
OPERATING YOUR TV A. ZAPP FUNCTİON (OPTİONAL) D. TUNING THE TELEVISION Select the programme you would like to recall There are two ways of tuning your television: by pressing SWAP button. Selected programme • Manual, where you control the tuning process number will appear on the upper left side of the or Autoprogram where the television does it all screen.
Page 8
Starting with Program P1, tune in the first Enter the desired program number channel as follows: by using the Ten key program Use the Program up button to select buttons SEARCH.Press the Volume up or Use the Volume up/down buttons to Volume down button to start the select the program number.
Page 9
Use the Program down button to • Picture Menu select AUTOPROGRAM and press the OK button. To reach the picture menu press one time to MENU button. BRIGHTNESS Please Note: CONTRAST a) On the TV sets equipped with ATS a COLOUR COUNTRY SELECTION menu will appear.
Page 10
d) Language 1- Select the SLEEP TIMER in the FEATURES menu. Select the desired time by using Volume down or Volume up buttons. There are many languages available for the On 2- You can also use the YELLOW ( ) button on Screen Displays (OSD).
Page 12
IC DATASHEETS&SPECS TDA 9345 GENERAL DESCRIPTION The various versions of the TDA9345 and TDA9345 PS-N3 combine the functions of a video processor together with a µ-Controller, a Teletext decoder and US Closed Caption decoder. The Teletext decoder has an internal RAM memory for 1 page(TDA 9345) or 10 page(TDA 9346) text. The ICs are intended to be used in economy television receivers with picture tubes up to 100°.
Page 13
c) Data Capture • Automatic selection between 625 WST/VPS • Cursor • Special Graphics Characters with two planes, on line 16 of VBI • Real-time capture and decoding for WST allowing Teletext in Hardware, to enable optimized µ- four colours per character •...
Page 15
TDA 8357J GENERAL DESCRIPTION The TDA8357J is a power circuit for use in 90° and 110° colour deflection systems for 25 to 200 Hz field frequencies, and for 4 : 3 and 16 : 9 picture tubes. The IC contains a vertical deflection output circuit, operating as a high efficiency class G system.
Page 16
HEF 4053B DESCRIPTION The HEF4053B is a triple 2-channel analogue multiplexer/demulti plexer with a common enable input (E). Each multiplexer/demultiplexer has two independent inputs/outputs (Y0 and Y1), a common input/output (Z), and select inputs (Sn). Each also contains two-bidirectional analogue switches, each with one side connected to an independent input/output (Y0 and Y1) and the other side connected to a common input/output (Z).
Page 17
TDA 9830 TV sound AM-demodulator and audio source switch SYMBOL DESCRIPTION IFIN sound IF differential input signal n.c. not connected CAGC AGC capacitor CREF REF voltage filtering capacitor n.c. not connected AMOUT AM demodulator output AMIN input signal (from AM) to audio switch AFOUT output signal from audio switch EXTIN...
PIN VOLTAGES OF IC’s IC101(TDA 9345) TV signal processor-Teletext decoder with embedded Controller SYMBOL DESCRIPTION V DC(*) PIN SYMBOL DESCRIPTION V DC(*) P1.3/T1 port 1.3 or Counter/Timer 1 input 2,46(2,4) HOUT horizontal output 0,88(3,12) P1.6/SCL port 1.6 or I2C-bus clock line 4,88(0) FBISO flyback input/sandcastle output...
ELECTRICAL ADJUSTMENTS 1.1 Supply Voltage Adjustment Connect a digital voltmeter to the cathode of diode D609 at the AV mode of the TV and set the screen voltage to the minimum with the screen potentiometer. Adjust the main supply voltage (B+) with P601 potentiometer to the following value (after supply adjustment, readjust Screen and focus voltage).
Page 23
• Set the value of “BLACK LEVEL G” and “WHITE POINT B” to “30” and “32” with V+ / V- buttons. • Adjust “WHITE POINT R” and “WHITE POINT G” for red and green drives • If white balance can not be adjusted properly slightly change the values of “BLACK LEVEL G” and “WHITE POINT B”.
Page 24
2.7 Factory Settings for Service Mode Values given in Table 1 are typical values and can vary according to the CRT type. 21" 14" 15" 20" AGC(UHF) Automatic Gain Control 1(UHF) AGC(VHF) Automatic Gain Control 2(VHF) Automatic Gain Control for AGC(LPRIME) SECAM LL’...