Digi ConnectPort LTS 8 Quick Start Manual

1 What's in the box
USB1
XBee
Power
USB2
SD
ConnectPort LTS
DP-9F console adapter
XBee antenna
(W models only)
RJ-45 diagnostic loopback
Rack mount brackets
(16/32 port models only)
Ethernet cable
2
Connect the hardware
a
Connect the Ethernet cable to the Ethernet 1 port.
Connect the serial devices to the serial ports, following the pin-position
b
information below. If serial devices are EIA-422/485, see steps 4e and 4f.
c
Connect the power supply to the POWER connector.
d
W models only: Connect the XBee antenna to the XBEE connector.
Cord and brick power
supply (for LTS 8 models).
a c
b
Serial port side
ConnectPort LTS
Reverse side
d
Pin positions for connecting serial devices:
10-wire jack 10-wire connector
(female): (male):
ConnectPort LTS For a 10-wire
products use an connector, Pin 1
RJ-45 10-wire jack of the connector is
(female), with Pin 1 in the following
in the following location:
location:
Insertion
end
Pin 1
Serial port pin assignments:
Pin # on
Pin # on
10-wire
8-wire
connector
connector EIA-232
1 RI
2 1 DSR*
3 2 RTS
4 3 CGND
5 4 TxD
6 5 RxD
7 6 SGND
8 7 CTS
9 8 DTR
10 DCD*
*Use the Altpin setting to swap these two signals.
© 2015 Digi International Inc. Digi, Digi International Inc., ConnectPort, RealPort, and the Digi logo are trademarks or registered trademarks of Digi International Inc. in the United States and other countries worldwide. All other trademarks are the property of
their respective owners.
Up
Sel
Ext
Dn
Ready Diagnostic
C P L T S 8
O N N E C T O R T
Cord and brick power supply
(ConnectPort LTS 8 models only)
Power cord (US models only)
Power cord
(for U.S.
models).
8-wire connector
(male):
For an 8-wire
connector,
connect the pins
to the center 8 pins
of the 10-wire jack:
Insertion
end
Top Top
view view
MEI versions only:
EIA-422/485
EIA-485
Full-Duplex
Half-Duplex
N/A
TxD-
DATA-
RxD-
N/A
RTS+
CGND
CGND
N/A
TxD+
DATA+
RxD+
SGND
SGND
N/A
CTS+
N/A
RTS-
N/A
CTS-
Ports, connectors, LEDs, and buttons:
Ethernet 1
Power
–
+
Ethernet 2
Power
connector Ethernet
ports
SD
USB
SD card
ports
slot
ConnectPort LTS 16/32 - Serial port side
Power
Ethernet 1 17 18 19 20 21 22
Ethernet 2
1 2 3 4 5 6
Ethernet
Power
Serial ports
ports
connector
ConnectPort LTS 16/32 - Reverse side
Power
ExpressCard SD
Power
SD card
Express
LED
slot
card slot
(W models
only)
ConnectPort LTS 16 Dual Power - Serial port side
C P L T S 1 6
O N N E C T O R T
1 2 3 4 5 6
Serial ports
ConnectPort LTS 16 Dual Power - Reverse side
Console Factory Reset
Factory
Console
reset
port
button

Quick Start Guide

ConnectPort® LTS 8/16/32
ConnectPort LTS 8 - Serial port side
LTS W
C P
O N N E C T O R T
Modem
1 2 3 4 5 6 7 8
Analog
Serial ports
modem
port (W
models only)
ConnectPort LTS 8 - Reverse side
USB1
XBee
Power Ready Diagnostic
C
O N N E C T
USB2
XBee
Diagnostic
Power
antenna
LED
LED
connector
Ready
(W models
LED
only)
23 24 25 26 27 28 29 30 31 32
7 8 9 10 11 12 13 14 15 16
C
O N N E C T
USB1
Ready Diagnostic
XBee
USB2
Ready
XBee
USB
LED
antenna
ports
Diagnostic
connector
LED (W models
only)
7 8 9 10 11 12 13 14 15
C P
O N N E C T O R T
Power 1 Power 2 Ready Diagnostic
Ready
Power 1
LED LED
Diagnostic
Power 2
LED
LED
Console
Factory
DTR
Reset
DCD
Factory
Console
DTR/
reset
port
DCD
button
LEDs
Up
Sel
Ext
Dn
P L T S 8
O R T
LCD
LCD
display
control
buttons
Up
Sel
Ext
Dn
C P L T S 3 2
O N N E C T O R T
LCD
LCD
display
control
buttons
P
LTS
O R T
DTR
DCD
Factory Reset Console Modem
Factory
Analog
DTR/
Console
reset
modem
DCD
port
button
port (W
LEDs
models
only)
Ethernet 1
Power 2 Power 1
Ethernet 2
16
Ethernet
Power 1
ports
Power 2
connector
connector
LTS
Up
Sel Ext
Dn
SD
LCD LCD
SD card
control
display
slot
buttons