Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Zinwell ZWD-2500T
Summary of Contents for Zinwell ZWD-2500T
-
Page 3: Table Of Contents
Table of Contents TABLE OF CONTENTS ..................1 1. IMPORTANT INFORMATION ................2 ....................2 AFETY RECAUTIONS 2. INTRODUCTION ....................4 2.1 P ..................4 ACKING ONTENT 2.2 O ......................5 VERVIEW 3. INSTALLATION....................7 4. TROUBLESHOOTING ..................15 5. SUPPORTED RESOLUTION ................16 6. AUDIO FORMATS SUPPORT................17 7. PRODUCT SPECIFICATION ................18... -
Page 4: Important Information
1. Important Information Take time to read this user manual before you Danger: Be careful with electricity. use your ZWD-2500T and ZWD-2500R. It contains important information and notes Power to the units must be switched off regarding operating your wireless HD receiver before any work is undertaken, such as and transmitter. -
Page 5: Trademark Information
CE DECLARATION OF occur in a few particular installation. If the CONFORMITY interference is happened, increase the Zinwell Corporation declare under our separation distance between the transmitter and receiver. responsibility that the product is in ZWD-2500 is susceptible to interference... -
Page 6: Introduction
HDMI cable. Any display like LCD, PDP or computer monitor with HDMI input connector are applicable to our ZWD-2500R. Connect the ZWD-2500T to your multiple High-Definition devices such as Cable/Satellite Box, HD Set-Top Box, Blu-Ray DVD Player, Game Console, and Media Center PC hidden in your cabinet behind your seating area. -
Page 7: Overview
Plug the IR Blaster Extender Cable into the IR OUT jack at rear panel of the transmitter. Attach the IR blaster to the device connected to the ZWD-2500T. You can point the device’s existing remote at the ZWD-2500R receiver to control connected device. -
Page 8: Hdmi Out
HDTV set so that you can easily receive and relay the IR command for external device connected with ZWD-2500T. HDMI OUT Front Panel Buttons and LEDs Connect a HDMI cable. The other end connects to the HDTV set. -
Page 9: Installation
(2) Connect a set of RCA cables (green, blue, between the DC IN jack of the red-colored cables) between the Y/Pb/Pr IN ZWD-2500T and a mains socket. The LED jacks of the ZWD-2500T and indicator in the POWER button lights up in... - Page 10 Step2: HDTV set Connection with ZWD-2500R: (1) Connect the HDMI cable between the HDMI OUT jack of the ZWD-2500R and your HDTV set. Press the SOURCE/INPUT button on your TV’s remote to select “HDMI” video mode. (2) Attach one side of the provided Velcro (fastening tapes) to the receiver back cover.
- Page 11 Plug the IR Blaster cable into the IR If your connected device will be out of the OUT jack of the ZWD-2500T. direct line of sight of your remote Place the IR blaster head in the IR senor controls, plug the IR Sensor Extender...
- Page 12 Step4: Mounting the ZWD-2500R to the Wall (5) Place ZWD-2500R key holes over the (1) Refer the drawing of the last page that have protruding screws and slide down into relative position of the receiver key holes position. and attach this paper on wall. (2) Drill pilot holes.
- Page 13 If it’s under Standby mode (The POWER LED shows red), press the TRANSMITTER and RECEIVER POWER button to turn on the ZWD-2500T and ZWD-2500R. (3) During warm-up, the POWER LED will blink blue until the signal link between ZWD-2500T and ZWD-2500R is established.
- Page 14 (4) Ensure your LCD TV set or projector is set to HDMI input mode and already powered on. (5) Press the Source 1HDMI 2HDMI 3YPbPr 4YPbPr button, until you see the available video from your device. (6) If you have some electronic devices like cordless phone, wireless access point/ router used with 5GHz channel frequency near the ZWD-2500, you may experience no/noise picture or diminished sound quality.
- Page 15 Note: (1) How to change to a different wireless channel for ZWD-2500: 1. Enter wireless RF channel 2. Changes to the next 3. Exit the wireless RF adjustment mode RF wireless channel channel adjustment mode There is no button on the Press the CHANNEL Press the CHANNEL Method...
- Page 16 3 signal strength. Please refer the next LED details part: Note: (1) Make sure your multiple High-Definition devices connected with ZWD-2500T have already powered on. (2) Warming-up or source switching time should be approximately 15~20 seconds during the normal operation.
-
Page 17: Troubleshooting
4. Troubleshooting Problem Solution The ZWD2500 front panel • Check that the power plug of ZWD-2500T/ZWD-2500R power indicator (red LED) is properly inserted into a functioning power outlet. doesn't light up. • Verify that the proper cable has been selected and installed between the desired transmitter input connector and your High-Definition device. -
Page 18: Supported Resolution
Formats support. 5. Supported Resolution If the SOURCE LED continues to blink blue (slower than no signal mode) and there is no/abnormal video displayed, this is an indication that video format from your A/V source device is not supported. Ensure that the consumer timing of your HD device is compliant with below detail sheet. -
Page 19: Audio Formats Support
6. Audio Formats Support Analog Audio from Base Band audio L/ R inputs: Convert to 2-channel by fixed 24 bits/sample with sampling rate 48KHz by I S bus over Wireless High-Definition Interface transmission Digital Audio from HDMI inputs: Support up to 3.072Mbit/s 16~ 24 bits/sample with sampling rate 32~ 48KHz 2 channels PCM by S bus. -
Page 20: Product Specification
Supported IR Blasting Frequency 36 KHz/ 38 KHz Power Supply 100~ 240V AC in, 5V 3A DC out Power Adaptor Operating Temperature 0~40°C Regulations FCC, CE, VCCI, NCC ZWD-2500T ZWD-2500R Interfaces HD Wireless Video HD Wireless HD Video Transmitter Receiver Sets...