Advertisement
Quick Links
Zinwell ZMX-7500/DSE7500 Tuning Guides
For adding Bravo+1, Prime, Duke+1 and Prime+1
These instructions may take up to 30 minutes to complete.
Step 1
Check First
Please confirm that the green signal bar that appears for a short time at the bottom of the screen when you change channels
is 100% on both TV1 and TV3.
If this green bar is less than 95% on TV1, These instructions may fail. Click
here
to some tips which might solve the problem.
If you have a healthy green signal bar then go to next step
Step 2
On your remote press Menu
Then go down to System Configuration using the down arrow key.
Advertisement
Related Manuals for Zinwell ZMX-7500
Summary of Contents for Zinwell ZMX-7500
- Page 1 Zinwell ZMX-7500/DSE7500 Tuning Guides For adding Bravo+1, Prime, Duke+1 and Prime+1 These instructions may take up to 30 minutes to complete. Step 1 Check First Please confirm that the green signal bar that appears for a short time at the bottom of the screen when you change channels is 100% on both TV1 and TV3.
-
Page 2: Then
The default password is "0000" unless you have changed it, If 0000 doesn't work, use "1269" instead. The password will revert to "0000" after a Restore to Defaults". Select Yes and then when requested pull the small black power plug, out of the right hand corner of your Zinwell Freeview Receiver. - Page 3 Step 5 You will now see a menu like this: With your remote, go down to LNB 1 and check if the Signal Box (Located on the bottom right is showing a Yellow bar (100% or equivalent). If not? then toggle right and wait a few seconds and see if the signal box shows any signal. This is normally either LNB 1 or LNB Once you have found which LNB has the signal at 100% then proceed to the next step.
- Page 4 Use the remote to go down to Auto Tune Enter in the password Step 8 1. On the remote toggle Right (You will see the drop down as seen above) 2. Use the arrow keys to select the "User Satellite”. (Do not select Optus D1 or you may lose existing channels and you will need to go back to Step 2 ) If you don't see another Satellite other than Optus D1, please go back to Step 4...
- Page 5 4. Use the remote arrow key to go down 1 to Start Freq MHz 5. Enter 12480 (Don't Push the OK button yet) 6. Then, use the remote arrow key to go down 1 to END Freq MHz 7. Enter 12486 (Don't Push the OK button yet) 8.
- Page 6 The receiver will start scanning and after about 30 seconds the TVNZ channels (including Maori Television) will be duplicated. Press Ok and confirm save. Exit. Step 10 When you have returned to normal TV, Press MENU Then go down to System Installation, using your remote's arrow keys, toggle right and then toggle down to EDIT TP. Press OK. Enter password.
- Page 7 NOTE: If you see an existing entry with a Freq of 12519 you will need to delete that first using the Delete TP option in the previous menu or you will get a “TP Exists” error when you try to change 12483 to 12519 as instructed below. You will now see a screen similar to the one above.
- Page 8 Change the new Transponder Frequency (TP) from *12483 to 12519 as shown above Confirm the Symbol Rate (SR) is 22500, Polarisation is Hori (Horizontal), press OK and save. (Note: you will see the yellow signal bar as soon as you enter 12519.) Step 12 It will now scan.
- Page 9 Locate Maori Television on channel 9 and press 5 Rename to BravoPlus1. (Need Rename Help - see the end of these instructions) Press OK and remain in Channel Manager Locate *TVNZ 1 on channel 10 and press 5 Rename to Prime Press OK and remain in Channel Manager Locate *TVNZ 2 on channel 12 and press 5 Rename to DukePlus1...
-
Page 10: Table Of Contents
Then.. Toggle to 17: Press 4 (Delete – a red cross will appear at the end of the line as shown), Then cursor down to 18: Press 4 Then cursor down to 20: Press 4 and finally OK and confirm Step 16 Press Menu Toggle right and then toggle down to EDIT CHANNEL... -
Page 11: Step 18
You will see a screen like the one above. Use the arrow buttons to select the 9 BravoPlus1 entry as shown Using the Remote you need to match the information as shown in the picture above: e.g. For 9 BravoPlus1 Audio: 1114 Press OK and toggle right;... -
Page 12: Press Menu
You will HOWEVER be able to access the EPG of these channels from another channel e.g. TV1 TV2 etc If you have a Widescreen TV, here are the additional steps to adjust your ZMX-7500 or DSE-7500 for a wide screen picture... - Page 13 After you have renamed your channel, Press ok on your remote to save and exit. You can adjust the upper case by moving the blue arrow down to the bottom row and then press 9 Made a mistake? Press the AUDIO Button on the remote to delete. http://freeviewforum.co.nz/forum/topics/how-to-use-the-rename-guide-on-the-dse7500-and-zinwell-zmx7500 Graham Wilson 027 205 7999 grahamw@gmx.com...