Motorola T5583 User Manual

®
Important Information on Safe and Efficient Operation
Read This Information Before Using Your Radio.
TWO-WAY RADIO
The information provided in this document supersedes the general
USER'S GUIDE
safety information in user guides published prior to December 1, 2002.
Transmit and Receive Procedure
Your two-way radio contains a transmitter and a receiver. To control
your exposure and ensure compliance with the general
population/uncontrolled environment exposure limits, always adhere to
the following procedure:
• Transmit no more than 50% of the time.
• To receive calls, release the PTT button.
• To transmit (talk), press the Push to Talk (PTT) button.
Transmitting 50% of the time, or less, is important because the radio
generates measurable RF energy exposure only when transmitting (in
terms of measuring standards compliance).
Exposure to Radio Frequency Energy
Your Motorola two-way radio complies with the
following RF energy exposure standards and guidelines:
• United States Federal communications Commission, Code of Federal
Regulations; 47CFR part 2 sub-part J
• American National Standards Institute (ANSI)/Institute of Electrical
and Electronic Engineers (IEEE) C95. 1-1992
• Institute of Electrical and Electronics Engineers (IEEE) C95.1-1999
Edition
Model T5583
KEM-PK15560-02A
• International Commission on Non-Ionizing Radiation Protection
(ICNIRP) 1998
• Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure
to Radio frequency Electromagnetic Fields in the Frequency Range
from 3 KHz to 300 GHz, 1999
• Australian communications Authority Radio communications
(Electromagnetic Radiation—Human Exposure) Standard, 2003
• ANATAL ANNEX to Resolution No. 303 of July 2, 2002 "Regulation of
limitation of exposure to electrical, magnetic and electromagnetic
fields in the radio frequency range between 9 KHz and 300GHz" and
"Attachment to resolution #303 from July 2, 2002"
To assure optimal radio performance and make sure human exposure
to radio frequency electromagnetic energy is within the guidelines set
forth in the above standards, always adhere to the following
For More Information
procedures.
For further information, you may call: Portable Radio Operation and EME Exposure
Antenna Care
Alcom Electronics Pte LTD
Use only the supplied or an approved replacement antenna.
37, Kallang Pudding Road,
Unauthorized antennas, modifications, or attachments could damage
Blk-B Tong Lee Building,
the radio and may violate regulations.
#05-08, Singapore 349315
Do NOT hold the antenna when the radio is "IN USE." Holding the
PH: (65) 6841 2668 , FAX: (65) 6841 2628 antenna affects the effective range.
E-MAIL: support@alcom.com.sg
Body-Worn Operation
To maintain compliances with RF exposure guidelines, if you wear a
radio on your body when transmitting, always place the radio in a
Motorola-supplied or approved clip, holder, holster, case or body
harness for this product. Use of Non-Motorola-approved accessories
may exceed RF exposure guidelines.
If you do not use one of the Motorola-supplied or approved body-worn
accessories and are not using the radio held in the normal use
position, ensure the radio and its antenna are at least 1 inch (2.5 cm)
from your body when transmitting.
Data Operation
If applicable, when using any data feature of the radio with or without
an accessory cable, position the radio and its antenna at least one
inch (2.5 cm) from the body.
Approved Accessories
For a list of approved Motorola accessories, visit out Web site at
www.motorola.com.
Electromagnetic Interference/Compatibility
Note: Nearly every electronic device is susceptible to electromagnetic
interference (EMI) if inadequately shielded, designed or otherwise
configured for electromagnetic compatibility. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference; and
2. This device must accept any interference received, including
interference that may cause undesired operation.
Facilities
To avoid electromagnetic interference and/or compatibility conflicts,
turn off your radio in any facility where posted notices instruct you to
do so. Hospitals or health care facilities may be using equipment that is
sensitive to external RF energy.
Aircraft
When instructed to do so, turn off your radio when onboard on aircraft.
Any use of a radio must be in accordance with applicable regulations
per airline crew instructions.
Medical Devices – Pacemakers
The Advanced Medical Technology Association recommends that a
minimum separation of 6 inches (15 cm) be maintained between a
handheld wireless radio and a pacemaker. These recommendations are
consistent with the independent research by and recommendations of
the U.S. Food and Drug Administration.
People with pacemakers should:
Safety and General Information
• ALWAYS keep the radio more than 6 inches (15 cm) from their
pacemaker when the radio is turned ON.
• Not carry the radio in the breast pocket.
• Use the ear opposite the pacemaker to minimize the potential for
interference.
• Turn the radio OFF immediately if there is any reason to suspect that
interference is taking place.
Medical Devices – Hearing Aids
Some digital wireless radios may interfere with some hearing aids. In
the event of such interference, you may want to consult your hearing
aid manufacturer to discuss alternatives.
Other Medical Devices
If you use any other personal medical device, consult the manufacturer
of your device to determine if it is adequately shielded from RF energy.
Your physician may be able to assist you in obtaining this information.
Safety and General Use While Driving
Check the laws and regulations regarding the use of radios in the area
where you drive, and always obey them. If you do use your radio while
driving, please:
• Give full attention to driving and to the road.
• Use hands-free operation, if available.
• Pull off the road and park before making or answering a call if driving
conditions so require.
Do not place a portable radio in the area over an air bag or in the air
bag deployment area. Air bags inflate with great force. If a portable
radio is placed in the air bag deployment area and the air bag inflates,
the radio may be propelled with great force and cause serious injury to
occupants of the vehicle.
Safety and General Use During Activity
The use of a two-way radio while engaged in activities requiring concentration
may cause distraction or otherwise impair your ability to safely participate in
such activities. Always use technology safely.
Potentially Explosive Atmospheres
Turn off your radio prior to entering any area with a potentially explosive
atmosphere. Only radio types that are especially qualified should be
used in such areas as "Intrinsically Safe." Do not remove, install or
charge batteries in such areas. Sparks in a potentially explosive
atmosphere can cause an explosion or fire resulting in bodily injury or
even death.
Note: The areas with potentially explosive atmospheres referred to
above include fueling areas such as below decks on boats, fuel or
chemical transfer or storage facilities, areas where the air contains
chemicals or particles (such as grain, dust or metal powders) and any
other area where you would normally be advised to turn off your vehicle
engine. Areas with potentially explosive atmospheres are often—but not
always—posted.
Blasting Caps and Areas
To avoid possible interference with blasting operations, turn off your
radio when you are near electrical blasting caps, in a blasting area, or in
areas posted "Turn off two-way radios." Obey all signs and instructions.
Operational Cautions
Antennas
Do not use any portable radio that has a damaged antenna. If a damaged
antenna comes into contact with your skin, a minor burn can result.
Batteries
All batteries can cause property damage and/or bodily injury such as
burns if a conductive material—like jewelry, keys or beaded chains—
touch exposed terminals. The conductive material may complete an
electrical circuit (short circuit) and become quite hot. Exercise care in
handling any charged battery, particularly when placing it inside a
pocket, purse or other container with metal objects.
Battery Charger Safety Instructions:
Save these Instructions
1. Do not expose the charger to rain or snow.
2. Do not operate or disassemble the charger if it has received a sharp
blow, or has been dropped or damaged in any way.
3. Never alter the AC cord or plug provided with the unit. If the plug will
not fit the outlet, have the proper outlet installed by a qualified
electrician. An improper condition can result in a risk of electric
shock.
4. To reduce the risk of damage to the cord or plug, pull the plug rather
than the cord when disconnecting the charger from the AC receptacle.
5. To reduce the risk of electric shock, unplug the charger from the outlet
before attempting any maintenance or cleaning.
6. Use of an attachment not recommended or sold by Motorola may
result in a risk of fire, electric shock or personal injury.
7. Make sure the cord is located so it will not be stepped on, tripped over
or subjected to damage or stress.
8. An extension cord should not be used unless absolutely necessary.
Use of an improper extension cord could result in a risk of a fire
and/or electric shock. If an extension cord must be used, make sure
that:
• The pins on the plug of the extension cord are the same number, size
and shape as those on the plug of the charger.
• The extension cord is properly wired and in good electrical condition.
• The cord size is 18 AWG for lengths up to 100 feet, and 16 AWG for
lengths up to 150 feet.
9. The supply cord of this charger cannot be replaced. If the cord is
damaged, please refer to warranty section.
Control Buttons Using the Desk Stand Charger (Optional Accessory)
The desk stand charger provides drop-in charging convenience for NiMH batteries
and can be placed on any flat surface, such as a desk or workbench. Charge the
Use to:
NiMH battery overnight (at least 16 hours) before using it for the first time.
• Select menu options
After the initial charge, an empty battery is fully charged within 14 hours.
• Exit the menu (when
Use to: pressed while in a
menu) 1. Turn the radio off and remove the battery cover.
• Turn radio on/off
• Lock and unlock the 2. Remove the battery pack from the clear plastic bag. Do not disassemble or
• Adjust volume
keypad (when held
unwrap the battery pack.
down and not in a
menu)
3. Insert the NiMH battery pack so the metal contacts on the side of the battery
are facing outward from the radio to connect with the contacts on the
battery door.
4. Reposition the battery cover and press down to secure.
LED Indicator Light
5. Plug the AC power supply into the plug on the desk stand.
T5583
6. Plug the AC power supply into a standard wall outlet.
Use to:
7. Remove the battery pocket inserts from the charger pockets.
• Talk
• Save a setting 8. With a radio facing forward, slide it into one of the charging pockets.
Notes
Accessory Jack
• The light on the charging base will glow continuously when radio/battery
Use to:
Use to:
is inserted.
• Transmit call tone
• Scan
• When moving between hot and cold temperatures, do not charge the battery
until the battery temperature acclimates (usually about 20 minutes).
Removable front cover • For optimal battery life, remove the radio or battery from the charger within
Use and to:
16 hours. Do not store the radio in the charger.
• Scroll through menus
Speaker
Attaching the Belt Clip
Microphone 1. Align the belt clip post with the hole in the back of the radio.
2. Gently push until the clip clicks into place.
Removing the Belt Clip
1. Push down on the release tab at the top of the belt clip to release the catch.
2. Pull the belt clip away from the back of the radio.
Turning Your Radio On and Off
Display Screen Guide
Turn clockwise to turn the radio on and counterclockwise to turn the radio
off. The radio chirps and the display briefly shows all feature icons available on
your radio.
Setting the Volume
Rotate while holding down
listening level. Rotate
Numbers for
to decrease the volume.
Codes
To communicate, all radios in your group must be set to the same channel
and Interference Eliminator Code.
Numbers for
To talk, press and hold
Channel,
Call Tone when talking. When you finish talking, release
release to listen.
Setting a Channel
– Battery Meter
Your radio has 8 channels. Channels 1-8 are .5 watt.
1. With the radio on, press
– Lock
2. Press or
3. Press to confirm your selection or
PTT
– Talk Confirmation Tone
Channels and Frequencies
(Roger Beep)
Channel
1
– Scan
2
– Hands-Free
3
(Vox/iVox)
4
Talk Range
Your radio is designed to maximize performance and improve transmission range.
Getting Started
Do not use the radios closer than 5 feet apart.
Installing the AA Batteries
Checking the Channel Before Transmitting
Your radio uses 3 AA Alkaline batteries.
Your radio has multiple channels shared on a "take turns" basis. For
1. With the back of the radio facing you, lift the battery latch up to release
uninterrupted communication, do not talk on a channel if someone else is
the battery cover and remove the cover.
currently talking on it.
2. Insert 3 AA Alkaline batteries as shown on the inside of the battery
To check for activity on a channel before you talk, press and hold
compartment.
If you hear static, the channel is clear to use.
3. Reposition the battery cover and press down to secure.
Push to Talk Timeout Timer
Note: The T5583 model radios can use a NiMH rechargeable battery instead
To prevent accidental transmissions and save battery life, the radio emits a
of 3 AA Alkaline batteries. A rechargeable battery upgrade kit, is available
continuous warning tone and stops transmitting if you press
for these radios.
continuous seconds.
Installing the NiMH Battery Pack
Interference Eliminator Code
1. Follow step 1 above to remove the battery cover.
Interference Eliminator Codes help minimize interference by providing you with
2. Remove the battery pack from the clear plastic bag.
a choice of code combinations.
Do not disassemble or unwrap the battery pack.
To set the code for a channel:
3. Insert the NiMH battery pack so the metal contacts on the side of the
1. Press
battery are facing outward from the radio to connect with the contacts
2. Press
on the battery door.
3. Press to
4. Reposition the battery cover and press down to secure.
You can set a different code for each channel using this procedure.
Battery Meter
Note: You must set the Interference Eliminator Code to
The battery icon shows the battery charge level, from full to
uses Interference Eliminator Codes to communicate with other FRS radios that
empty . When the battery is empty, the radio chirps periodically after
do not have Interference Eliminator Codes.
releasing . The radio powers off when the voltage drops below a
PTT
predetermined level to protect the rechargeable battery.
Note: Remove the batteries before storing your radio for extended periods of
time. Batteries corrode over time and may cause permanent damage to
your radio.
Locking the Keypad
To avoid accidentally changing your radio settings, press
seconds or until displays. You can turn the radio on and off, adjust the
volume, receive, transmit, send a call tone, and monitor channels. All other
functions are locked. To unlock the radio, press and hold
or until is no longer displayed.
Scanning Channels
Use scanning to monitor channels and codes for transmissions or to find
someone in your group who has accidentally changed channels.
To start scanning, briefly press and release
displays . When the radio detects channel activity, it stops scanning and you
can hear the transmission. To respond to the transmitting, press
5 seconds.
Advanced Scan
If the radio stops scanning on a channel you do not want to listen to, briefly
press and release
Removing Channels from the Scan List (Nuisance Delete Feature)
To remove a channel so the radio does not stop on it while scanning, press
and hold or for at least 3 seconds, then release. This temporarily
removes the channel from the scan list.
To restore the channel, turn the radio off and then back on.
Note:You cannot remove the channel your radio was set to when you started
the scan (called your home channel).
Alerts
Channel Busy Indicator
When a channel is busy, the LED flashes twice per second.
Setting and Transmitting Call Tones
Your radio can transmit different call tones to other radios in your group so you
until you reach a comfortable can alert them that you want to talk.
clockwise to increase the volume or counterclockwise
To set a call tone:
1. With the radio on, press
and displays.
Talking and Listening 2. Press or to change and hear the call tone.
3. Press or to set the new call tone.
PTT
To transmit your call tone to other radios set to the same channel and
Interference Eliminator Code as your radio, press
. Hold the radio 2 to 3 inches away from your mouth
PTT
Notes
(press to talk),
PTT
• The T5583 model has 10 call tones.
• Setting the call tone to
Transmitting a Talk Confirmation Tone
You can set your radio to transmit an unique tone when you finish transmitting.
. The current channel flashes.
It's like saying Roger or Over to let others know you are finished talking.
to set the channel. • To turn talk confirmation on, press and hold
to continue set up.
When you release
PTT
and displays.
• To turn talk confirmation off, turn your radio off and then back on
Frequency (MHz) Channel Frequency (MHz)
while pressing and holding
446.00625 5 446.05625
446.01875 6 446.06875
446.03125 7 446.08125
446.04375 8 446.09375
.
for 60
PTT
until the code starts to flash.
or to select the code.
save the code setting.
PTT
on an FRS radio that
Special Features
and hold for 3
for 3 seconds
. The scan indicator
within
PTT
or to resume scanning for the next active channel.
Alerts
3 times. The current call tone setting flashes
.
disables the call tone feature.
while you turn the radio on.
after transmitting, your call tone transmits
.
T5583