Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Longshine LCS-GSP8108
Summary of Contents for Longshine LCS-GSP8108
- Page 1 LCS-GSP8108 8-Port Gigabit Ethernet PoE+ Desktop Switch User’s Manual English...
-
Page 2: Fcc Certifications
FCC Certifications This Equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. -
Page 3: Ce Mark Warning
including interference that may cause undesired operation. CE Mark Warning This equipment complies with the requirements relating to electromagnetic compatibility, EN 55022 class B for ITE, the essential protection requirement of 2004/108/EC Council Directive on the approximation of the laws of the Member States relating to electromagnetic compatibility. - Page 4 Copyright © 2012, All Rights Reserved.
-
Page 5: Unpacking Information
Unpacking Information Thank you for purchasing this product. Before installation, please verify that your package contains the following items. One 8-port Gigabit Ethernet with 8-port PoE+ Desktop Unmanaged Switch 1* AC power cord Rubber feet and screws User’s Manual 2* Brackets 1*Wall mount accessory Introduction General Description... - Page 6 duplex mode. It is ideal for micro-segmenting large networks into smaller, connected subnets for improved performance, enabling the bandwidth demanding multimedia and imaging applications. Moreover, the 10/100/1000Mbps auto-sensing ability provides an easy way to migrate 10/100Mbps to 1000Mbps network with no pain. This switch supports PoE, which supplies power for connected devices via CAT 5 and above twisted cables.
-
Page 7: Key Features
Key Features Complies with 10BASE-T specifications of the IEEE802.3 standard Complies with 100BASE-TX specifications of the IEEE802.3u standard Complies with 1000BASE-T specifications of the IEEE802.3ab standard Compliant with IEEE 802.3af/at PoE standard (DTE power via MDI) Provides 8 PoE ports with classification identify Supports 31.5W maximum per PoE port Supports over current protection and circuit shorting protection... - Page 8 Provide 8* 10/100Mbps auto-detect （half/full） and 1000Mbs full duplex switch ports (IEEE802.3/ 802.3u/ 802.3ab) Supports MDI/MDI-X auto crossover Supports 136W Max; Full load: 31.5W(at) x 4P + 5W = 131W ; 15.4W(af) x 8P + 5W = 128.2W Wire-speed packet filtering and forwarding rate Store-and-forward architecture filters fragment &...
-
Page 9: The Front Panel
The Front Panel The front panel consists of LED indicators and the ports. For detailed LED definition, please refer to the next paragraph. The front panel of the switch is shown as below: LED Definition The switch contain 1* power LED and 1* loop LED for the device, 1* PoE LED for each port and 1* Link/Act LED for each port. - Page 10 Status Operation Steady Green The switch is powered on Power The switch is powered off Blinking Red There is a loop existing Loop There is no loop existing Port LED The switch provides one “Link/ACT” LED and one PoE LED for each port. Status Operation Steady Green...
-
Page 11: The Rear Panel
The Rear Panel Power Receptacle To be compatible with the electric service standards around the world, the switch is designed to afford the power supply in the range from 100 to 240VAC, 50/60Hz. Please make sure that your outlet standard to be within this range. -
Page 12: Desktop Installation
Installation This switch can be placed on your desktop directly, or mounted in a rack. The installation is a snap. Users can use all the features of the switch with simply attaching the cables and turning the power on. Before installing the switch, we strongly recommend: The switch is placed with appropriate ventilation environment. -
Page 13: Rack Mount Installation
the switch to keep the switch from slipping. The recommend position has been square-marked. Install the switch on a level surface that can support the weight of the unit and the relevant components. Plug the switch with the female end of the provided power cord and plug the male end to the power outlet. -
Page 14: Wall Mount Installation
Locate a mounting bracket over the mounting holes on one side of the unit. Insert the screws and fully tighten with a suitable screwdriver. Repeat the two previous steps for the other side of the unit. Insert the unit into the rack and secure with suitable screws (not provided). - Page 15 1. Use drill bit to insert the two plastic screws into the wall. Insert the two iron screws into the hole of the two plastic screws respectively. Place the switch onto the iron screws through the wall-mount slots to make the switch hanging on the wall.
- Page 16 Network Cables Installation Crossover or straight-through cable: All the ports on the switch support Auto-MDI/MDI-X functionality. Both straight-through or crossover cables can be used to connect the switch with PCs as well as other devices like switches, hubs or router. Category 3,4,5,5e or 6 UTP/STP cable: To make a valid connection and obtain the optimal performance.
- Page 17 Media Speed Wiring 10 Mbps Category3,4,5 UTP/STP 10/100/1000 100 Mbps Category 5 Mbps ports UTP/STP 1000 Mbps Category 5e, 6 UTP/STP Ports that 10/100/1000 Category5,5e,6 support PoE Mbps UTP/STP or (Port 1~Port8) above...
-
Page 18: Product Specifications
Product Specifications IEEE802.3 10BASE-T IEEE802.3u 100BASE-TX IEEE802.3ab 1000BASE-T Standard IEEE 802.3af/at PoE standard (DTE power via MDI) IEEE802.3x flow control 8 * 10/100/1000 Mbps auto Interface MDI/MDI-X RJ-45 ports (Port 1~8 support PoE power feeding) Network Data 10/100/1000Mbps Auto-negotiation Rate Transmission 10/100Mbps: Full-duplex, Half-duplex Mode...