Advertisement
CAUTION:
Caution statements advise against certain conditions and practices that may result in
damage to vehicles, appliances and/or the Jumpstarter 400 Mk2.
IMPORTANT:
Although this unit is delivered in a partially charged state, you must fully charge it with
the supplied 110/120 Volt AC charger for a full 24 hours before using it for the first
time. You cannot overcharge the unit using the AC charger method.
1 . Use only the supplied cords/adapters for recharging this unit. Do not recharge for
more than 3-4 hours maximum using 12 Volt DC method. Recharge unit after
each use.
2.
All On/Off switches should be in the OFF position when the unit is charging or not in
use. Make sure all switches are in the OFF position before connection to a power
s o u rce or load.
3.
Never insert anything other than the supplied power/recharging cords or
recommended appliance power/recharging cords into the 12 Volt DC charging/ power
socket on this unit. Do not use any accessory that is not recommended or provided
by the manufacturer.
4.
Do not use this unit to operate appliances that draw more than 20 amps.
5.
This system is designed to be used only on vehicles with 12 Volt DC battery systems.
Do not connect to a 6 Volt or 24 Volt battery system.
6.
This system is not designed to be used as a replacement for a vehicular battery. Do not
attempt to operate a vehicle that does not have a battery installed.
7.
Vehicles that have on-board computerized systems may be damaged if vehicle b a t t e ry
is jump-started. Before Jumpstarting, read the vehicle's owners manual to confirm
that external-starting assistance is advised.
8.
Excessive engine cranking can damage a vehicle's starter motor. If the engine fails to
start after the recommended number of attempts, discontinue jump-start procedures
and look for other problems that may need to be corrected.
9.
Although this unit contains a non-spillable battery, it is recommended that unit be kept
upright during storage, use and recharging. To avoid possible damage that may short-
en the unit's working life, protect it from direct sunlight, direct heat and/or moisture.
10. Check unit periodically for wear and tear. Replace worn or defective parts immediately.
Contact the Customer Service department toll-free 866-584-5504.
11. Do not attempt to jump-start a frozen battery.
12. Never submerge this unit in water.
3
INTRODUCTION
The J U M P S TA RT 400 Mk2 internal battery is a high density sealed, lead-acid battery that
stores and delivers energy comparable to full sized ordinary jump-starters. Please read this
guide carefully before use to ensure optimum performance and avoid damage to the unit
or items that you are using it with.
The JUMPSTART 400 Mk2 & 12 VOLT DC POWER SUPPLY is a compact, durable and
portable jump-start system for vehicles and boats that have a standard 12 Volt battery
system. This self-contained, rechargeable system will start most vehicles and boats. It
can also be used as a safe, portable source of 12 Volt DC electric power in remote loca-
tions and/or emergency situations.
Use the JUMPSTART 400 Mk2 to:
Jump-start any engine system with a standard 12 Volt DC battery: boat; truck; car;
•
airplane; RV; personal watercraft; snowmobile; garden tractor; gasoline engine gener-
ator, etc.
Operate: 12 Volt DC fans, inflators, fluorescent worklights, cellular phones (can quick-
•
charge a cellular phone by using the phone's 12 Volt DC adapter cord), spotlights,
TVs, portable radios, cassette or CD players, and more.
Operate: Certain 110/120 Volt AC Accessories (requires a West Marine 12 volt power
•
inverter, sold separately).
The JUMPSTA RT 400 Mk2 has an easy-to-read series of LED (Light Emitting Diode) charge
indicators that show when the unit is fully charged, or the level of charge in the battery.
Charge level can be viewed when the charge status push button is pressed. A 12 Volt DC
power accessory socket is provided for use with appliances that can operate from a vehicle
12 Volt DC accessory outlet. This allows maximum portability and utility when the
J U M P S TA RT 400 Mk2 is used in remote locations.
The JUMPSTA RT 400 Mk2 can be recharged from any standard 110/120 Volt AC power
s o u rce using the supplied AC Recharge Adapter. The adapter barrel connector attaches to
the Recharge Port on the top panel of the jump-starter. A built-in 12 Volt appliance socket
and the appropriate DC/DC charging/adapter cord is used to recharge the battery from
another 12 Volt DC source. When pressed, the CHARGE STATUS button will show the bat-
t e ry power level status (from Low to Full). The green LED full indicator illuminates when the
unit is fully recharged and charging can be discontinued. An ON/OFF switch operates the
built-in work/emergency light.
4
Advertisement
