Related Manuals for Returnstar IQBoard IR Pro
Summary of Contents for Returnstar IQBoard IR Pro
- Page 1 IQBoard IR Pro & IR-D Pro User Manual Copyright(C) 2003-2012 Fuzhou Returnstar Technology Co., Ltd. Websites: www.recoverystar.com; www.iqboard.net Tel: 0086-591-87274373 Fax: 0086-591-87274383 E-mail: master@iqboard.net...
- Page 2 Statement This manual is for IQBoard IR Pro & IR-D Pro. Both Whiteboard and Interactive Whiteboard in this manual refer to IQBoard IR Pro or IQBoard IR-D Pro. Colorless Writing Pen (Finger) is used for IQBoard IR Pro or IQBoard IR-D Pro.
-
Page 3: Table Of Contents
CONTENT CHAPTER 2 SPECIFICATIONS ....................... 5 2.1 P ..........................5 ERFORMANCE 2.2 F ..................5 LEXIBLE IXING AND ELOCATING ETHODS 2.3 D ....................... 5 URABLE URFACE OLID 2.4 PC C ........................... 5 ONNECTION 2.5 IQB IR P & IR-D P .................... -
Page 4: Chapter 1 Product Introduction
IQBoard IR Pro / IR-D Pro is provided with powerful IQBoard Software, which makes your operation on interactive whiteboard more convenient. Through IQBoard Software, various interactive teaching and demonstrating functions can be achieved, such as... -
Page 5: Chapter 2 Specifications
Chapter 2 Specifications 2.1 Performance Resolution: 9600×9600, 600dpi; Signal tracking rate: 8m/s; Signal processing rate: 480 dots/s; Orientation: 4, 9 or 20 points 2.2 Flexible Fixing and Relocating Methods Fixing methods include wall hanging, cabinets, and mobile stand. Provide optional height adjustable mobile stand for 50-120 inch whiteboards, the height can be adjusted from 1.88M to 2.12M. -
Page 6: Iqboard Ir Pro & Ir-D Pro Models
2.5 IQBoard IR Pro & IR-D Pro Models RP060, RP080, RP085, RP0100 and RP105 refer to IQBoard IR Pro in relevant sizes. RPD060, RPD080, RPD085, RPD0100 and RPD105 refer to IQBoard IR-D Pro in relevant sizes. N means hotkeys and pen tray are not included. W means board surface supporting normal pen writing. -
Page 7: Chapter 3 How To Install Iqboard
Chapter 3 How to Install IQBoard 3.1 Mount Whiteboard 3.1.1 For Product with an “M” in Its Hardware SN In case your product has an “M” in its hardware SN, you can select wall mounting by 2 anchor bolts fixing on the wall. Parts list Picture Name... - Page 8 Step 2. According to the distance of the two Anchor Bolts, fix the Wall Mounting Bracket on each screw on the top frame of backboard. Please make sure to fix the Wall Mounting Brackets symmetrically on the backboard to keep the balance (as shown in the figure).
-
Page 9: For Product With A "Y" In Its Hardware Sn
3.1.2 For Product with a “Y” in Its Hardware SN In case your product having a “Y” on its hardware SN, you can select either wall mounting by 4 anchor bolts fixing on the wall or stand mounting. 3.1.2.1 Wall Mounting Part list Picture Name... - Page 10 Step 3. Align the Anchor Bolts with the clip holes of Height Adjustable Bracket on backboard, and then hang the whiteboard on the wall. Note: You can adjust the height of whiteboard by hanging the whiteboard on different height of clip holes on Height Adjustable Bracket (The distance between lower frame of whiteboard and floor is 75-80cm recommended ).
-
Page 11: Stand Mounting
3.1.2.2 Stand Mounting Parts list Picture Name Quantity Leg Bar Column Supporting Bar Caster Moveable Crossbeam (each includes 2 Beams and a U-shaped Groove; for 100″, 112″ and 120″ whiteboards, Beams and U-shaped Grooves are especially lengthened) Hexagon Bolt A Hexagon Bolt B (M8×50, with 08/22 washer) Hexagon Bolt C (M8×50) - Page 12 Hexagon Bolt Set A (M8×50) (each set includes: 1 hexagon bolt, 1 wind nut, 1 M8 nut, 1 small washer and 1 big washer) Hexagon Bolt Set B (M8×35) (each set includes: 1 hexagon bolt, 1 wind nut, 1 small washer and 1 big washer) Anchor Bolt (M8×60) Open-end Wrench...
- Page 13 Step 3. Install the other end of each Supporting Bar on each Leg Bar, using Hexagon Bolt Set A. In this stage, please partially screw the bolt, leaving 4mm clearance between bolt head and Column for hanging whiteboard. Step 4. Install 2 Casters on each Leg Bar. Step 5.
- Page 14 Step 6. Lay down and connect the two leg assemblies with U-Shaped Grooves. Step 7. Secure U-Shaped Grooves with Hexagon Bolt Set B. In this stage, do not completely tighten the bolt in order to adjust the stand width later. Step 8.
- Page 15 Hexagon Bolt Sets A. Please make sure to fix the Brackets symmetrically on the backboard to keep the balance (as shown in the figure). Note: You can adjust the height of whiteboard by screwing the Brackets on different height of backboard (The distance between lower frame of whiteboard and floor is 75-80cm recommended).
- Page 16 Fully assembled whiteboard is as follows:...
-
Page 17: Chapter 4 How To Connect To Computer And Projector
Chapter 4 How to Connect to Computer and Projector After fixing the whiteboard, find a connecting port at the bottom of left corner protector. Plug the USB Standard-B into the connecting port, and plug the USB Standard-A into the available USB port of computer, as follows. External power source is not required. And please connect the projector into the VGA port of your PC video card. -
Page 18: Chapter 5 How To Install And Uninstall Driver
5.2 How to Uninstall Driver Select “Start > Programs > IQBoard IR Pro Drivers (or IQBoard IR-D Pro Drivers) > Uninstall” to uninstall. You also can open Control Panel, select “Add/Remove Programs”, and in the list of currently installed Programs, select “IQBoard IR Pro... -
Page 19: Chapter 6 How To Setup Iqboard
To orient the whiteboard Please do as following steps when you orient the whiteboard: Step 1. Select “Start > Programs > IQBoard IR Pro Drivers (or IQBoard IR-D Pro Drivers) > Orient” or press on the hotkey bar if your whiteboard is with hotkeys. -
Page 20: Hotkey Settings
If you select interactive whiteboard with soft hotkeys, at the first time you use the whiteboard, you need to set these hotkeys. Step 1. Select “Start > Programs > IQBoard IR Pro Drivers (or IQBoard IR-D Pro Drivers) > Hotkey Settings” to enter Hotkey Settings window as follow Step 2. - Page 21 Step 3. Follow the indication on screen, click relevant hotkey in sequence. After the setting is completed, you can use these hotkeys. Note: 1. When setting the soft hotkeys, if some error occurs, you can press “ESC” key on the keyboard to exit the setting process, and then reset the hotkeys.
-
Page 22: Chapter 7 How To Use Iqboard
Chapter 7 How to Use IQBoard 7.1 Basic Operations For IQBoard IR Pro & IR-D Pro, you can use the enclosed pen or your finger to write or perform Mouse function. Following are the tips for some basic operations: Single-click If you use pen or finger, press the surface with the pen or finger tip at proper strength. -
Page 23: How To Use Hotkeys On Whiteboard
7.2 How to Use Hotkeys on Whiteboard Following is the introduction of above soft hotkeys. Add Page : In Windows Mode, press this key to clear all annotations on screen. In Board Mode, Press this key to add a new page in current .cdf file. Save File : In Windows Mode, press this key to save all annotations on screen to a page in current file. -
Page 24: How To Use Gesture Recognition
The default setting of gesture recognition is off. If you want to enable it, please select “Start >Programs > IQBoard IR Pro Drivers (or IQBoard IR-D Pro Drivers) > Gesture Recognition Settings”, and then select the “Enable the Gesture Recognition” check... -
Page 25: Customize Gesture Recognition Sensitivity
7.3.2 Customize Gesture Recognition Sensitivity Move slider to adjust Move the sliders to change the value of each range for functions. The wider the value range, the easier you can perform the related function. Perform to adjust An intelligent way to adjust the gesture recognition is performing your hand gesture to customize the function of Pen, Mouse and Eraser. -
Page 26: How To Use Smart Pen Tray
3) You can set Key4 to Blue Pen or Eraser by enter the following Hotkey Settings Window by clicking “Start > Programs > IQBoard IR Pro Drivers (or IQBoard IR-D Pro Drivers) > Hotkey Settings” to enter the setting window as follow... -
Page 27: Chapter 8 Faq
Chapter 8 FAQ 1. What kind of orientation precision should I select? It depends on your requirement of orientation time and accuracy. You have the following choices: Quick orientation (4 points): for fast orientation Standard orientation (9 points): for most of situations Precise orientation (20 points): for high-definition system 2. - Page 28 Please reconnect the cable with the board to initialize the hardware again. 5.What if part of area in IQBoard IR Pro & IR-D Pro can not work or write? 1) Hardware initialization failed. Please reconnect USB cable and try again when hardware initialization is finished.
-
Page 29: Chapter 9 Cautions And Maintenance
Chapter 9 Cautions and Maintenance 9.1 Whiteboard For the interactive whiteboard that do not support normal marker (no “W” included in the product model), please try not to use normal marker to write on the surface. Before cleaning, please shut down the computer and switch the projector into standby mode to make the dirt more obvious. -
Page 30: Usb Cable
To avoid harm from improper operation, please do not use chair or other tool to help short students use the whiteboard. If students are not tall enough to use the whiteboard, please low down the whiteboard under the help of the professional technician.
Need help?
Do you have a question about the IQBoard IR Pro and is the answer not in the manual?
Questions and answers