Advertisement
Notes
For DC Power Type
• When installing the camera on a ceiling or a wall, not to disturb adjustment of Tilt Base angle fix
Resistance of copper wire [at 20C˚ (68˚F)]
the BNC-Power Cable on the Pan Base clip.
Copper wire size (AWG)
<Installing the camera on a ceiling>
<Installing the camera on a wall>
Resistance ( Ω / m)
BNC-Power Cable
Voltage Drop (V/m)
• As the voltage drop according to the length of the cable in the above table, a camera may
malfunction if there is an excessively long cable run.
* Voltage for camera operation: 12V DC ±10%
Switch functional demo sticker
* Voltage drops in the above table are variable according to types of cable manufacturer.
Functional selection switch
• When installing the camera on a ceiling or a wall, fuctional selection switch should be bottom-left
Connection to Monitor
and switch function demo sticker under the lens.
Connect the VIDEO-OUT jack to the VIDEO-IN jack of monitor.
•As a connecting method varies according to instruments, refer to the manual supplied with
Connection to Power
the instrument.
•Connect the cable after power is turned off.
•Connect the adapter to the power input connector as shown in the figure below. Use a
•Set the 75Ω / Hi-Z selection switch. If it is a intermediate device, switch it to Hi-z and if
DC 12V. (The Adapter is not provided with the Dome Camera.)
it is final device, switch it to 75Ω. (Please refer to the Monitor Manual.)
Adapter (not provided)
Power Input Connector
DOME Camera
MINI DOME CAMERA
7
USER'S MANUAL
Notes
TROUBLESHOOTING
• To use BLC more effective, Adjust the subject to be over 20% of full screen.
If you have trouble operating your camera, refer to the following. If the guidelines do not
• Switch to BLC OFF when the background has strong white.
enable you to solve the problem, contact an authorized technician.
The image on the screen is dim.
• Check if the lens are stained. If dirty, clean the lens with soft, clean cloth.
(2) White Balance Control (ATW/AWC)
• The image is dimmer at night than daytime. If the focus is not right, adjust it at daytime.
The contrast on the screen is too weak.
Select the desired control mode using ATW/AWC switch.
• Adjust the contrast feature of the monitor.
• ATW(Auto Tracing White balance): The camera automatically controls the white
• If the camera is exposed under too strong light, change the camera position.
balance in any environment.
• Adjust the lens BACK FOCUS again.
• AWC(Auto White balance Control): In order to obtain the best image, menu the
The camera is not work properly, and the surface of the camera case is hot.
switch from ATW to AWC while the camera
• Check that you have connected the camera to a proper power (DC12V ).
focuses on white paper.
Background is too bright.
• Deactivate BLC control feature.
(3) Sharpness
DIMENSION
The switch emphasize the sharpness. To soften the edge move this Swich
to Normal.
(4) Flickerless (SID-42C Series Only)
In this function electronic shutter speed is fixed in 1/100sec(1/120sec: PAL
model). FL function can compensate the flicker caused by power frequency,
but set OFF in the area not using a 60Hz(50Hz: PAL model) AC power.
MINI DOME CAMERA
11
USER'S MANUAL
Panning & Tilting Control
You can adjust the Panning and Tilting angle freely. (Panning angle: 360°,
#24(0.22mm
2
)
#22(0.33mm
2
)
#20(0.52mm
2
)
#18(0.83mm
2
)
Tilting angle: 10°~90°)
0.078
0.050
0.030
0.018
Tilt Base Holding Screws
0.028
0.018
0.011
0.006
Pan Base
You can rotate the lens from 360˚
1) Adjustment Panning angle: After attaching the dome camera to a ceiling or a wall, adjust the
panning angle for better monitoring area by rotating the Pan Base. The panning angle can be
adjusted 360° freely.
2) Adjustment Tilting angle: After attaching the dome camera to a ceiling or a wall, adjust
the tilting angle for better monitoring area by rotating the Tilt Base. The tilting angle can
be adjusted to 10° from 90° freely. (based the ceiling surface)
Notes
• After loosening Pan or Tilt Base holding screws, adjust its angle. And then tighten screws again.
BNC
• AWC(Auto Balacne Control): In order to obtain the best image, mode the switch from ATW to AWC
while the camera focuses on white paper.
• In case of adjusting the tilting, do not take the lens for preventing hysical shocks. Please take the Tilt Base.
• This dome camera is to be installed on the ceiling by factory default. In case of using camera on the wall,
readjust the Tilt angle as page 7 (Notes).
Intermediate
Monitor
DOME Camera
MINI DOME CAMERA
8
USER'S MANUAL
SPECIFICATION
Item
Input power
Power Consumption
Operating
& Humidity
Dimension
Weihgt
Pickup Device
Video Output
Min. illumination
Synchronizaion
S/N
Resolution
Lens (Built-in)
Ø 63mm
ESC
Ø 85.5mm
White Balance
BLC
Shrpness
68mm
Flickerless
Monitoring
Pan
Angle
Tilt
MINI DOME CAMERA
12
USER'S MANUAL
CONFIGURATION OF DIP-SWITCHES
Use the DIP switches inside of the camera for selecting functions.
Tilt Base
You can adjust up and down
the camera (10°~90°).
Pan Base Holding Screw
(1) Backlight Compensation (BLC)
Switch it to BLC to obtain the clear picture, the finest detail and perfect light
contrast althongh there is strong backlight.
•BLC ON: When the image is in front of strong background lighting, your camera allows you
to get the clear image.
•BLC OFF : Deactivate BLC control feature.
- To use BLC more effective, Adjust the subject to be over 20% of full screen.
- Switch to BLC OFF when the background has strong white.
MINI DOME CAMERA
9
USER'S MANUAL
MINI DOME CAMERA
DECLARATION OF CONFORMITY
Application of Council Directive(s)
SIC-22CN
SIC-22CP
SIC-42CN
SIC-42CP
Manufacturer's Name
DC 12V ± 10%
Manufacturer's Address
1.4W
1.5W
-10C˚ ~ +50C˚ [-14˚F ~ 122˚F] / 30% ~ 90% RH
European Representative Name
85.5mm(Ø) x 68mm(H)
European Representative Address
160g
Equipment Type/Environment
Model Name
1/3" color interline-transfer CCD
Beginning Serial NO.
1Vp-p Composite 75Ω unbalanced
Year of Manufacture
0.4Lux / F1.2
0.7Lux / F1.2
Conformance to
INT
more than 48dB (Weight ON)
more than 330TV Line
more than 480TV Line
Fixed Lens 92˚, Focal Length 3.7mm, F2.2
1/60(1/50) ~ 1/120,000sec
We, the undersigned, hereby declare that the equipment specified above conforms to the above
ATW / AWC Selectable
Directive(s).
ON / OFF Selectable
Manufacturer
SAMSUNG TECHWIN CO., LTD
High / Normal selectable
Signature
Not Used
ON / OFF selectable
Full Name
YOUNG TAEK SON
360˚
Position
QUALITY CONTROL MANAGER
10˚ ~ 90˚
Place
CHANGWON, KOREA
Date
2003. 11. 1
MINI DOME CAMERA
13
USER'S MANUAL
SID-42C Series
SID-22C Series
10
USER'S MANUAL
89 / 336 / EEC
SAMSUNG TECHWIN CO., LTD
SAMSUNG TECHWIN CO., LTD
42, SUNGJU-DONG CHANGWON-CITY,
KYUNGNAM, KOREA, 641-120
MINI DOME CAMERA
SID-42CP / 22CP
S3B00001
2003. 11. 1
EN 50081-1 : 1992
EMC-Directive 89/336 EEC and 92/31/EEC
EN 50130-4 : 1996
Legal Representative in Europe
Signature
Full Name
Position
Place
Date
Advertisement
