1. Safety and Precautions CAUTION * The service of this LCD-TV must be carried out by qualified persons only. * Do not change any module unless the set is switched off. CLEANING:Always disconnect unit from mains supply before attempting to clean it. Use soft cloth moistened with soapy water, wipe gently.
Page 4
Don’t listen to headphones at high volume, as such use can permanently damage your hearing. Don’t obstruct the ventilation of the equipment, for example, with curtains or soft furnishings. Overheating will cause damage and shorten the life of the equipment. Don’t allow electrical equipment to be exposed to rain or moisture.
Page 8
(for TV only) NOTE: Audio out : The level of audio output cannot be changed using the volume , treble , and bass controls on your TV . These connectors should be used with an external audio amplifier that can be used to control the volume. VCR Recording: The main display must set to TV mode in order to use the audio and video output to record a program using a VCR .
4. Controls Location The buttons control your TV’s basic features, including the on-screen menu. To use the more advanced features, you must use the remote control. POWER: turn on or turn off the LCD TV. SOURCE: set up the input source (PC, TV, SCART Video/ SCART RGB , Video, S-Video, Component) MENU: display the main menu.
5. Remote Control The remote control pad works almost same as ordinary TV remote control that includes the basic function needed while viewing a live video. DISPLAY : Display the current source or program digits .
Summary of Control Buttons Selecting the Signal Source Switch to the TV mode. Switch to the PC mode. SCART Switch to the Video mode or RGB mode from SCART. VIDEO/S-V Switch to the Video mode from RCA socket or S-Video mode. COMPONENT Switch to the Component mode (YPbPr or YCbCr).
REVEAL Press “REVEAL“ button to display concealed information, such as solutions of riddles or a quiz. EXPAND Press “EXPAND“ button to enlarge the top half or bottom half of the Teletext page. SUB-PAGE/TIME Press “SUB-PAGE/TIME“ button to access to the sub-page you required.
6. Disassembly Instructions 1) Face down the LCD-TV : Face down the LCD-TV on a smooth plane with a soft material to protect the panel faceplate . 2) Tuner Board Removal : Note: If only repair the Tuner Board , needn’t disassemble the Swivel Base and Back Cover .
Page 14
3) Swivel Base Removal : 3.1 Loosen 2 screws and remove Neck Cover . (Indicated as “A” ) 3.2 Loosen 4 screws from Neck Bracket and remove the Swivel Base . (Indicated as “C” ) 4) Back Cover Removal : 4.1 Remove the Tuner Cover by pressing and sliding .
Page 15
5) Right & Left Side Covers Removal : 5.1 Loosen 4 screws from Right & Left Side Covers . (Indicated as “F ”) 5.2 Loosen 2 screws from the 15 pin D-Sub connector on the right side of the panel. (Indicated as “F’...
Page 16
6) Metallic Shield Removal : 6.1 Loosen 8 screws from Metallic Shield of Main-PCB . (Indicated as “H”) 6.2 Remove Metallic Shield of Main-PCB from Main Bracket and then the Main Board shows up. 7) MCU Removal (if need ) : 7.1 Clamp up the MCU by using an MCU clamp.
8. Troubleshooting 8.1 Symptom Codes ( for Call Center use ) CODE SYMPTOM COUNTERMEASURES • No Picture and No Sound Make sure the Power cord and Aerial Cable are in TV mode. properly connected . • Make sure the batteries in remote control are not flat. •...
Page 19
CODE SYMPTOM COUNTERMEASURES • Stripe noise . Check the coaxial cable connected with the TV is not oxidized • Do not use 300 ohm twin lead cables as interference may occur • It is recommended to use a 75 ohm coaxial cable (not supplied) to get premium quality picture.
Page 20
CODE SYMPTOM COUNTERMEASURES • “Out of Range” message Maximum PC resolution supported is 1024x768 / 1280 x 768, so the screen will appear “Out of range” at higher resolution. • Reduce the resolution to 1024x 768/ 1280x 768 from PC . •...
8.2 Flow Chart ( for Repair Center Use ) (1) Power Start NG No Backlight & No LED ADP8 Replace Is the Output of Adapter 12V ? AC Adapter F001 Replace Is the Voltage of L046 12V ? Replace Is the Voltage of I014 &...
(2) No Backlight , but LED lights up No Backlight ,but LED lights up Still No Replace backlight Which Color does Green Check & Re-plug U901 (Inverter) PA17 (from Inverter) Display ? I019 (Scaler) POWER Press key & Is it entering into Reset the MCU(I012) by DC 12V Adapter Re-plug...
Page 23
(3) No picture , but Backlight & LED light up No Picture , but Backlight & LED light Up Is the Voltage of L044 5V Replace Q003/I025/L042 (Panel 5V I/P) ? Do all of the Replace Does have sources have No I001 picture? Picture ?
Page 24
(4) Picture Abnormal or Halt Picture Abnormal / Halt Steps to Refresh EEPROM : StepsM After pressing 1. Press POWER key to turn off RESET button ,does the the LCD-TV. picture recover normal? 2. Press CH. Down key on the top of LCD-TV (don’t release ) and then press POWER After pressing...
Page 25
(5) Frame Defects or Striped Lines at all sources The Ver. or Hor. Sync. haven’t been held at all sources. Are the Outputs of Does the wire Does the wire PA18 I019 (TP6760) PA18 connect connect firmly to V901 Replace normal ? firmly with LCD P018 &...
9. Electronic Circuit Description 9.1 Main Board Circuit 1) Power Refer to sheet 7 of PWB-0579 circuit diagram. DC +12V output of AC adaptor is applied to the LCD-TV through socket P020. This supply is fed directly to P017#1、2 (Connector to Inverter) and I010#4 (Audio Amp.
Page 27
3) TV Signal Refer to sheet 11、8、9 of PWB-0579 circuit diagrams. The IEC plug on tuner UT01 receives TV picture and Sound signals from aerial .Tuner UT01(Tuner-FQ1216ME/MK3) is a multi-standard TV tuner for CCIR B/G, D/K, I, L/L’ system and the front-end has a built-in digitally (I C) PLL tuning system .
Page 28
5) Panel interface Refer to sheet 6 of PWB-0579 circuit diagrams. The signals of panel interface are all applied from Scaler I019(TP6760) to LCD Panel through connector P018、P019 and wire PA18. The signals SHFCLK、PDE、 PVYSNC 、 PHSYNC from I019 #90~94 are applied to LCD panel via connector P018. These four signals are used for panel display controls.
Page 29
9.2 Tuner Board Circuit Refer to sheet 11 of PWB-0579 circuit diagrams. UT01(Tuner-FQ1216ME/MK3) is a multi-standard TV tuner for CCIR B/G, D/K, I, L/L’ system and the front-end has a built-in digitally (I C) PLL tuning system . The Output of Composite Video from QT01 #Emitter fed with Tuner UT01 is applied to SAA7118 through P013#10 .
Page 30
9.3 Key、LED&IR Board Circuit Refer to Key、LED and IR circuit diagram of PWB-0475 in Chapter10.2. * Key : The Keyboard is connected with Main Board through socket P021 and wire PA21 and to control the I012 (MCU) , so if the operation of key is fail , the I012 (MCU) may fail .
14. Mechanical Parts List PARTS NO. DESCRIPTION SP-SCREEN 5642382104 FRONT COVER 5642288709 IR LENS 5642382200 LCD MBRACKET 5642722701 RIGHT D-SUB COVER 5642420005 LEFT YPBPR COVER 5642421103 MPCB SHIELD 5646250602 MPCBSHIELD-2 5646251700 5642847102 FUNCTION KEY BACK COVER 5642288806 TUNNER COVER 5642420104 HAND BACK 5642901104 NECK BACK COVER...