Advertisement
Portable use
WARNING: THE HEATER SHOULD NEVER BE USED AS A PORTABLE
APPLIANCE WITHOUT THE FEET SECURELY FITTED.
WARNING: ONLY THE SCREWS SUPPLIED WITH THIS PRODUCT
SHOULD BE USED TO MOUNT THE FOOT. A MAXIMUM SCREW
LENGTH OF 10MM SHOULD BE USED.
Lay the heater on its back and remove the wall mounting brackets - see
Wall mounting. Locate and remove the foot fixing screw - see Fig. 2(a).
Clip the foot in place and secure using the foot fixing screw.
NOTE – The wall mounting brackets must be removed before the foot
can be fitted.
Wall Mounting (Installed)
Three identical wall mounting brackets are secured to the base of the heater
with a fixing screw. To wall mount appliance, first remove the brackets as
follows, lay the heater on its back and follow the sequence shown - see
Fig. 3. Identify and remove the fixing screw securing the brackets located
beside mains cable as shown in (a), pull out brackets and rotate them to
disengage them from the slot and withdraw the brackets from the slot (b).
Select a suitable position, near to a mains power socket whilst ensuring
the minimum mounting clearances are maintained - see Fig. 1. Fix the
two top retaining brackets to the wall, using suitable fixings – see Fig. 4.
Locate the heater on the top brackets and allow it to hang in place.
Fit the bottom bracket into the slot in the heater and then fix it to the wall.
Test that the heater is now securely fixed to the wall.
Controls
Thermostat
knob
Neon
Heat selector
switch
Mechanical
Timer
Model 403TSTi
574
478
Thermostat
knob
Control
switch
Neon
Model 403TSF
Thermostat (all models)
The thermostat controls the heat output according to the room temperature.
This ensures that the heater will not produce heat unnecessarily when the
room is warm.
To set the temperature you require, gradually turn the thermostat knob
clockwise until the desired temperature is reached. Allow some time
between increments for the room temperature to stabilise.
Alternatively to heat a cold room quickly, turn the thermostat knob to the
Max position. When the room has reached the desired temperature, turn
the thermostat knob anti-clockwise until the thermostat clicks off. The heater
will then automatically maintain this room temperature.
The thermostat also has a frost protection setting marked ' '. This setting is
useful in areas such as garages to prevent frost damage. If the thermostat is
set to its minimum setting ' ', the heater will cycle ON and OFF to maintain
a temperature of approximately 5°C to help protect against frosty conditions.
Switches (selected models)
Some models are supplied with selector switches . There are two switch
types, one is an on/off switch and the other is a heat selection switch.
Depending on model either one or both switch may be included. The switch
operation is as follows.
Fig. 2
On/ Off:
Heat selection
403TS Operation
This model contains an On/Off switch and a heat selection switch and
operates as follows.
When O/I switch is in position O the product is off regardless of any
other setting. When O/I switch is in position I and the I/II switch is in the
I position there is a 2kw output from the product. When O/I switch is
in position I and the I/II switch is in the II position there is a 3kW output
from the product. The indicator neon is always on when the product is
connected to the mains supply.
403TSTi Operation
This model contains a heat selection switch and an electro-mechanical
timer and operates as follows.
When the timer is switched to I and the I/II switch is in position I there is
Fig. 3
a 2kW output from the product. When the timer is switched to I and the
I/II switch is in position II there is a 3kW output from the product. When
the timer is in the ' ' position and the I/II switch is in position I there is a
2kW output from the product when the timer is set on. When the timer is
in the ' ' position and the I/II switch is in position II there is a 3kW output
from the product when the timer is set on. The indicator neon is always
on when the product is connected to the mains supply.
Mechanical Timer
Fig. 4
Set the I -
O
Fig. 5
O
-
Off
I
-
On
I
-
Low heat
II
-
High heat
(403TSTi)
19
-
slide switch on the timer (Fig.7) to:
Position
- Heating Off
I
Position I - Manual operation
This setting allows power to the heater
uninterrupted by the timer settings. The heat
selector switch will control the output (see
heater).
Position
- 'Auto' operation
DO NOT disconnect this heater from the mains
supply unless it is being taken out of use (e.g.
in summer or for storage), otherwise the timer
Fig. 7
clock will stop.
I
O
Fig. 6
Advertisement
