Page 1 FIAT 500 2 0 1 5 O W N E R ’ S M A N U A L I n f o r ma t i o n P r o v i d e d b y :...
Page 2 FIAT is a registered trademark of Fiat Group Marketing & WARNING! Corporate Communication S.p.A., used under license by Chrysler Group LLC.
Page 3: Introduction
TABLE OF CONTENTS SECTION PAGE INTRODUCTION ............. 3 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE .
Page 4 I n f o r ma t i o n P r o v i d e d b y :...
Page 5: Table Of Contents
INTRODUCTION CONTENTS INTRODUCTION ......4 VEHICLE IDENTIFICATION NUMBER ..7 HOW TO USE THIS MANUAL ....5 VEHICLE MODIFICATIONS/ALTERATIONS .
Page 6: Introduction
- all essentials that are maintaining its validity traditional to our vehicles. • The range of additional services available to FIAT This Owner’s Manual has been prepared with the assis- Group Automobiles customers tance of service and engineering specialists to acquaint NOTE: After reviewing the owner information, it you with the operation and maintenance of your vehicle.
Page 7: How To Use This Manual
INTRODUCTION 5 HOW TO USE THIS MANUAL Consult the Table of Contents to determine which section contains the information you desire. Since the specification of your vehicle depends on the items of equipment ordered, certain descriptions and illustrations may differ from your vehicle’s equipment. The detailed index at the back of this Owner’s Manual contains a complete listing of all subjects.
Page 8 6 INTRODUCTION I n f o r ma t i o n P r o v i d e d b y :...
Page 9: Vehicle Identification Number
INTRODUCTION 7 WARNINGS AND CAUTIONS This Owners Manual contains WARNINGS against op- erating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against proce- dures that could result in damage to your vehicle. If you do not read this entire Owners Manual, you may miss important information.
Page 10: Vehicle Modifications/Alterations
8 INTRODUCTION VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Stamped VIN Location NOTE: It is illegal to remove or alter the VIN. I n f o r ma t i o n P r o v i d e d b y :...
Page 11: Things To Know Before Starting Your Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A WORD ABOUT YOUR KEYS ... . .11 ▫ Remote Key Unlock, Driver Door/All Doors 1st Press .......16 ▫...
Page 12 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Power Window Switches ....22 ▫ Transporting Pets ..... .74 ▫...
Page 13: A Word About Your Keys
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 The vehicle is supplied with a code card containing key A WORD ABOUT YOUR KEYS code numbers to order duplicate keys, and the autho- The key fob contains the Remote Keyless Entry (RKE) rized dealer that sold you your new vehicle has the key transmitter with an integrated key.
Page 14 12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Before exiting a vehicle, always apply the parking brake, shift the transmission into PARK and re- move the Key Fob from the vehicle. When leaving the vehicle, always lock your vehicle. •...
Page 15: Locking Doors With A Key
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Key-In-Ignition Reminder WARNING! (Continued) Opening the driver’s door when the key is in the ignition • Do not leave children or animals inside parked and the ignition switch position is OFF/LOCK sounds a vehicles in hot weather.
Page 16: Replacement Keys
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: A key which has not been programmed is also Replacement Keys considered an invalid key, even if it is cut to fit the NOTE: Only keys that have been programmed to the ignition switch lock cylinder for that vehicle.
Page 17: General Information
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 General Information The Sentry Key® system complies with FCC rules part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. •...
Page 18: To Unlock The Doors And Liftgate
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Unlock The Doors And Liftgate To Lock The Doors And Liftgate Push and release the UNLOCK button on the RKE Push and release the LOCK button on the RKE transmit- transmitter once to unlock the driver’s door or twice, ter to lock all doors and the liftgate.
Page 19 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 1. Push the mechanical key release button and release the 2. Rotate the screw located on the side of the Key Fob mechanical key to access the battery case screw lo- using a small screwdriver. cated on the side of the Key Fob.
Page 20: General Information
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Take out the battery case. Remove and replace the General Information battery observing its polarity. This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: •...
Page 21: Door Locks
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 If your RKE transmitter fails to operate from a normal distance, check for these two conditions: 1. A weak battery in the transmitter. The expected life of the battery is a minimum of three years. 2.
Page 22 20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • Allowing children to be in a vehicle unattended is • Do not leave children or animals inside parked dangerous for a number of reasons. A child or vehicles in hot weather. Interior heat build-up may others could be seriously or fatally injured.
Page 23: Power Door Locks - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 Power Door Locks — If Equipped A power door lock switch is incorporated into the driver door handle. Push or pull the handle to lock or unlock the doors and liftgate. If the driver’s door handle is pushed a red lock indicator will show on the driver’s door handle (indicating locked) when the door is closed, the door will lock.
Page 24: Power Windows
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To change the setting proceed as follows: POWER WINDOWS 1. Briefly push the MENU button to enter the MENU Power Window Switches screen. There are single window controls located on the shifter bezel, below the climate controls, which operate the 2.
Page 25: Auto-Down
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 Auto-Down The driver’s door window switch has an Auto-Down feature. Push the window switch for approximately one second, release, and the window will go down automati- cally. To cancel the Auto-Down movement, operate the switch in either the up or down direction and release the switch.
Page 26: Liftgate
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LIFTGATE To unlock the liftgate, use the Remote Keyless Entry (RKE) transmitter or activate the power door lock switches located on the driver door handle. To open the liftgate, squeeze the liftgate release handle and pull the liftgate open with one fluid motion.
Page 27: Occupant Restraint Systems
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 OCCUPANT RESTRAINT SYSTEMS WARNING! Some of the most important safety features in your • Driving with the liftgate open can allow poisonous vehicle are the restraint systems: exhaust gases into your vehicle. You and your •...
Page 28 26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some simple steps you can take to minimize the 5. You should read the instructions provided with your risk of harm from a deploying air bag: child restraint to make sure that you are using it properly.
Page 29: Seat Belt Systems
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 ejection and the risk of injury caused by striking the WARNING! inside of the vehicle. Everyone in a motor vehicle should be belted at all times. • Never place a rear-facing child restraint in front of an air bag.
Page 30 28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE After the sequence completes, the Seat Belt Reminder NOTE: If BeltAlert has been deactivated, the Seat Belt Light remains illuminated until the respective seat belts Reminder Light will continue to illuminate while the are buckled.
Page 31 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 WARNING! WARNING! (Continued) • Do not allow people to ride in any area of your • Relying on the air bags alone could lead to more vehicle that is not equipped with seats and seat severe injuries in a collision.
Page 32 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • A lap belt worn too high can increase the risk of • A seat belt that is too loose will not protect you injury in a collision. The seat belt forces won’t be at properly.
Page 33 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 Lap/Shoulder Belt Operating Instructions WARNING! (Continued) 1. Enter the vehicle and close the door. Sit back and • A shoulder belt placed behind you will not protect adjust the seat. you from injury during a collision. You are more likely to hit your head in a collision if you do not 2.
Page 34 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Pulling Out The Latch Plate Inserting Latch Plate Into Buckle 3. When the seat belt is long enough to fit, insert the latch 4. Position the lap belt so that it is snug and lies low plate into the buckle until you hear a “click.”...
Page 35 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 6. To release the seat belt, push the red button on the buckle. The seat belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the seat belt to retract fully. Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt.
Page 36 34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Slide the latch plate upward over the folded webbing. WARNING! The folded webbing must enter the slot at the top of the latch plate. • ONLY use a Seat Belt Extender if it is physically required in order to properly fit the original seat 4.
Page 37 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 Seat Belts And Pregnant Women NOTE: These devices are not a substitute for proper seat belt placement by the occupant. The seat belt still must be We recommend that pregnant women use the seat belts worn snugly and positioned properly.
Page 38 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Switchable Automatic Locking Retractor (ALR) — If Equipped The seat belts in the passenger seating positions may be equipped with a switchable Automatic Locking Retractor (ALR) which is used to secure a child restraint system. For additional information, refer to “Installing Child Restraints Using The Vehicle Seat Belt”...
Page 39 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 In Automatic Locking Mode, the shoulder belt is auto- Driver Center Passenger matically pre locked. The seat belt will still retract to First Row remove any slack in the shoulder belt. The Automatic Second Locking Mode is available on all passenger seating positions with a combination lap/shoulder belt.
Page 40 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How To Engage The Automatic Locking Mode WARNING! 1. Buckle the combination lap and shoulder belt. • The seat belt assembly must be replaced if the 2. Grasp the shoulder portion and pull downward until switchable Automatic Locking Retractor (ALR) fea- the entire seat belt is extracted.
Page 41: Supplemental Restraint System (Srs)
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 • Supplemental Knee Air Bag Supplemental Restraint System (SRS) Air Bag System Components • Front and Side Impact Sensors Your vehicle may be equipped with the following air bag • Seat Belt Pretenioners system components: •...
Page 42 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Being too close to the steering wheel or instrument panel during Advanced Front Air Bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel.
Page 43 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 Advanced Front Air Bag Features the driver or front passenger seat belt is buckled. The seat belt buckle switch may adjust the inflation rate of the The Advanced Front Air Bag system has multistage Advanced Front Air Bags.
Page 44 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE On the other hand, depending on the type and location of WARNING! (Continued) impact, Advanced Front Air Bags may deploy in crashes • Relying on the air bags alone could lead to more with little vehicle front-end damage but that produce a severe injuries in a collision.
Page 45 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 The steering wheel hub trim cover and the upper right Supplemental Driver Knee Air Bag side of the instrument panel separate and fold out of the This vehicle is equipped with a Supplemental Driver way as the air bags inflate to their full size.
Page 46 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE When the SAB deploys, it opens the seam on the out- board side of the seatback’s trim cover. The inflating SAB deploys through the seat seam into the space between the occupant and the door. The SAB moves at a very high speed and with such a high force that it could injure you if you are not seated properly, or if items are positioned in the area where the SAB inflates.
Page 47 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 • Supplemental Side Air Bag Inflatable Curtains SABICs may help reduce the risk of head injury to front (SABICs): Located above the side windows. The trim and rear seat outboard occupants in certain side impacts. covering the SABICs is labeled SRS AIRBAG.
Page 48 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The SABICs and SABs (“Side Air Bags”) are designed to WARNING! activate in certain side impacts. The Occupant Restraint Controller (“ORC”) determines whether the deployment • Your vehicle is equipped with left and right Supple- of the Side Air Bags in a particular impact event is mental Side Air Bag Inflatable Curtains (SABICs).
Page 49 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 compartment. The Side Air Bags may deploy during WARNING! angled or offset frontal collisions where the Advanced Front Air Bags deploy. • Side Air Bags need room to inflate. Do not lean against the door or window.
Page 50 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If A Deployment Occurs • As the air bags deflate, you may see some smoke-like particles. The particles are a normal by-product of the The Advanced Front Air Bags are designed to deflate process that generates the non-toxic gas used for air immediately after deployment.
Page 51 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 Enhanced Accident Response System WARNING! In the event of an impact, if the communication network Deployed air bags and seat belt pretensioners cannot remains intact, and the power remains intact, depending protect you in another collision. Have the air bags, on the nature of the event, the ORC will determine seat belt pretensioners, and the seat belt retractor whether to have the Enhanced Accident Response Sys-...
Page 52 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE System Reset Procedure ignition switch is turned to the OFF position. In order to move your vehicle to the side of the road, you must Depending on the nature of the event the left and right follow the system reset procedure.
Page 53 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 Customer Action Customer Will See 7. Turn Left Turn Signal Switch OFF. (Turn Signal Left Turn Light is OFF. Right Turn Light is OFF. Switch Must be placed in Neutral State). 8. Turn ignition OFF. System is now reset and the engine may be started.
Page 54 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Warning Light will turn off. If the ORC detects a mal- • The Air Bag Warning Light comes on intermittently or function in any part of the system, it turns on the Air Bag remains on while driving.
Page 55 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 Maintaining Your Air Bag System WARNING! (Continued) • Do not attempt to modify any part of your air bag WARNING! system. The air bag may inflate accidentally or may • Modifications to any part of the air bag system not function properly if modifications are made.
Page 56 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Event Data Recorder (EDR) These data can help provide a better understanding of the circumstances in which crashes and injuries occur. This vehicle is equipped with an event data recorder (EDR). The main purpose of an EDR is to record, in NOTE: EDR data are recorded by your vehicle only if a certain crash or near crash-like situations, such as an air non-trivial crash situation occurs;...
Page 57: Child Restraints
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 Child Restraints WARNING! (Continued) Everyone in your vehicle needs to be buckled up at all great that you could not hold the child, no matter times, including babies and children. how strong you are. The child and others could be badly injured.
Page 58 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • For additional information, refer to www.seatcheck.org or call 1–866–SEATCHECK (732–8243). Canadian residents should refer to Transport Canada’s website for additional information: • www.tc.gc.ca/eng/roadsafety/safedrivers- childsafety-index-53.htm Summary Of Recommendations For Restraining Children In Vehicles Child Size, Height, Weight Or Recommended Type Of Child Restraint...
Page 59 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 Child Size, Height, Weight Or Recommended Type Of Child Restraint Small Children Children who are at least two Forward-Facing Child Restraint years old or who have out-grown with a five-point Harness, facing the height or weight limit of their forward in the rear seat of the rear-facing child restraint...
Page 60 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Infants And Child Restraints Children should remain rear-facing until they reach the highest weight or height allowed by their convertible Safety experts recommend that children ride rear-facing child seat. in the vehicle until they are two years old or until they reach either the height or weight limit of their rear-facing WARNING! child restraint.
Page 61 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 Older Children And Child Restraints WARNING! Children who are two years old or who have outgrown their • Improper installation can lead to failure of an infant rear-facing convertible child seat can ride forward-facing in or child restraint.
Page 62 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children Too Large For Booster Seats 5. Can the child stay seated like this for the whole trip? Children who are large enough to wear the shoulder belt If the answer to any of these questions was “no,” then the comfortably, and whose legs are long enough to bend child still needs to use a booster seat in this vehicle.
Page 63 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 Recommendations For Attaching Child Restraints Restraint Type Combined Use any attachment method shown with an “X” Below Weight of the LATCH – Seat Belt Only LATCH – Seat Belt + Top Child + Child Lower Anchors Lower Anchors Tether Anchor...
Page 64 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lower Anchors And Tethers For Children (LATCH) has three vehicle anchor points for installing LATCH- Restraint System equipped child seats. There are two lower anchorages located at the back of the seat cushion where it meets the seatback and one top tether anchorage located behind the seating position.
Page 65 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 LATCH Positions For Installing Child Restraints In This Vehicle Lower Anchorage Symbol 2 anchorages per • seating position Top Tether Anchorage Symbol • I n f o r ma t i o n P r o v i d e d b y :...
Page 66 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE What is the weight limit (child’s weight + 65 lbs (29.5 kg) Use the LATCH anchorage system until weight of the child restraint) for using the the combined weight of the child and the LATCH anchorage system to attach the child restraint is 65 lbs (29.5 kg).
Page 67 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 Can the rear-facing child restraint touch The child seat may touch the back of the the back of the front passenger seat? front passenger seat if the child restraint manufacturer also allows contact. See your child restraint owner’s manual for more information.
Page 68 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Locating The Upper Tether Anchorages Center Seat LATCH WARNING! There are tether strap anchorages behind each rear seating position located on the back of the This vehicle does not have a center seating position. seat.
Page 69 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 To Install A LATCH-Compatible Child Restraint 3. Attach the lower hooks or connectors of the child restraint to the lower anchorages in the selected seat- If the selected seating position has a Switchable Auto- ing position.
Page 70 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How To Stow An Unused ALR Seat Belt: WARNING! When using the LATCH attaching system to install a • Improper installation of a child restraint to the child restraint, stow all ALR seat belts that are not being LATCH anchorages can lead to failure of the re- used by other occupants or being used to secure child straint.
Page 71 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 Installing Child Restraints Using The Vehicle Seat Lap/Shoulder Belt Systems for Installing Child Belt Restraints in this Vehicle The seat belts in the passenger seating positions are equipped with a Switchable Automatic Locking Retractor (ALR) that is designed to keep the lap portion of the seat belt tight around the child restraint so that it is not necessary to use a locking clip.
Page 72 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE What is the weight limit (child’s weight + Weight limit of the Always use the tether anchor when using weight of the child restraint) for using the Child Restraint the seat belt to install a forward facing Tether Anchor with the seat belt to attach a child restraint, up to the recommended forward facing child restraint?
Page 73 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 Installing A Child Restraint With A Switchable 5. To lock the seat belt, pull down on the shoulder part of the seat belt until you have pulled all the seat belt Automatic Locking Retractor (ALR) webbing out of the retractor.
Page 74 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 9. Test that the child restraint is installed tightly by WARNING! (Continued) pulling back and forth on the child seat at the seat belt and Tethers for CHildren (LATCH) Restraint System” path. It should not move more than 1 inch (25.4 mm) for the location of approved tether anchorages in your in any direction.
Page 75 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 2. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. If your vehicle is equipped with adjustable rear head restraints, raise the head restraint, and where possible, route the tether strap under the head restraint and between the two posts.
Page 76: Transporting Pets
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ENGINE BREAK-IN RECOMMENDATIONS WARNING! A long break-in period is not required for the engine and • An incorrectly anchored tether strap could lead to drivetrain (transmission and axle) in your vehicle. increased head motion and possible injury to the Drive moderately during the first 300 miles (500 km).
Page 77: Safety Tips
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 CAUTION! WARNING! Never use Non-Detergent Oil or Straight Mineral Oil • Do not leave children or animals inside parked in the engine or damage may result. vehicles in hot weather. Interior heat build-up may cause serious injury or death.
Page 78: Exhaust Gas
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Exhaust Gas WARNING! (Continued) • If it is necessary to sit in a parked vehicle with the WARNING! engine running, adjust your heating or cooling Exhaust gases can injure or kill. They contain carbon controls to force outside air into the vehicle.
Page 79: Safety Checks You Should Make Inside The Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 not lit during starting, see your authorized dealer. If the Safety Checks You Should Make Inside The light stays on, flickers, or comes on while driving, have Vehicle the system checked by an authorized dealer. Seat Belts Defroster Inspect the seat belt system periodically, checking for cuts,...
Page 80 78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • Check mounting of mats on a regular basis. Always Pedals that cannot move freely can cause loss of properly reinstall and secure floor mats that have vehicle control and increase the risk of serious per- been removed for cleaning.
Page 81: Periodic Safety Checks You Should Make Outside The Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 Door Latches Periodic Safety Checks You Should Make Outside The Vehicle Check for positive closing, latching, and locking. Tires Fluid Leaks Examine tires for excessive tread wear and uneven wear Check area under vehicle after overnight parking for fuel, patterns.
Page 82 I n f o r ma t i o n P r o v i d e d b y :...
Page 83: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS POWER CONVERTIBLE TOP — IF EQUIPPED . .84 ▫ Heated Mirrors — If Equipped ... .90 ▫ Lowering The Power Top....84 ▫...
Page 84 82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Seat Height Adjustment ....101 ▫ Turn Signals ......110 ▫...
Page 85 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 ▫ To Resume Speed .....120 ▫ To Close ......129 ▫...
Page 86: Power Convertible Top - If Equipped
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The power top buttons will operate when the POWER CONVERTIBLE TOP — IF EQUIPPED ignition switch is turned to the ACC/ON/RUN position. On vehicles equipped with a power convertible top, the power convertible top switch is located on the overhead Lowering The Power Top console.
Page 87 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 NOTE: Rail lubrication is recommended every 2000 CAUTION! (Continued) cycles, or if scratching noises due to dust are present. • Use care when washing the vehicle, water pressure Refer to “Fluids, Lubes, and Genuine Part” in “Maintain- directed at the weather strip seals may cause water ing Your Vehicle”...
Page 88: Power Convertible Top Relearn Procedure
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 6. Hold the CLOSED button to move the top to the fully Power Convertible Top Relearn Procedure closed position. If your power convertible top does not operate in the Auto Opening/Closing mode (automatically opening/ 7.
Page 89: Wind Stop
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 Wind Stop The Wind Stop installs in the backseat area of the vehicle. The Wind Stop will not interfere with power top opera- tion. Therefore, it can remain installed when the top is up. MIRRORS Inside Day/Night Mirror The mirror can be adjusted up, down, left, and right for...
Page 90: Automatic Dimming Mirror - If Equipped
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activated.
Page 91: Power Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 The power mirror controls consist of a mirror select Power Mirrors switch and a four-way mirror control switch. To adjust a The power mirror controls are located on the driver’s mirror, press the mirror select switch to either the L (left) door trim panel.
Page 92: Folding Mirrors
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Spotter Mirror — If Equipped Folding Mirrors Some models are equipped with a driver’s side spotter The exterior mirrors are hinged to allow the mirror to mirror. The spotter mirror allows for a greater range of pivot forward or rearward to help avoid damage.
Page 93: Sun Visors
The sun visor can be Overview — If Equipped rotated downward or up against the door glass. Both sun Windows Mobile™-based FIAT BLUE&ME™ is a per- visors are equipped with courtesy mirrors. sonal telematic system enabling you to use communica- tion and entertainment applications expressly designed for use in the car.
Page 94: The Hands-Free Kit
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE having to take your eyes off the road or remove your The Hands-Free Kit hands from the steering wheel. To use voice commands The basic characteristic of this hands-free kit is voice you are not required to train the voice recognition system recognition with Bluetooth®...
Page 95 To get started with BLUE&ME™ hands-free kit with voice function display. Please refer to the Fiat Blue & Me Radio recognition, you have to simply pair your Bluetooth® wire- Supplement for further information.
Page 96 94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • To interact with BLUE&ME™ you can use either the The hands-free kit enables the following operations: buttons on the steering wheel or voice commands. • Contact Calling By Voice — You can call a contact in With voice recognition, you can perform system func- your mobile phone phonebook using your voice.
Page 97 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 • Conference Call — You can call another contact while After pairing and connecting your phone with the you are engaged in a phone conversation (with BLUE&ME™ system, you can make phone calls by Bluetooth®...
Page 98 96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Not all mobile phones support the SMS text message • To manage the list of SMS texts received on your reader function or automatic phonebook transfer via BLUE&ME™ paired mobile phone. Bluetooth®. For further information on the list of compatible •...
Page 99 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 Media Player • Audio File Selection By Category — You can play all audio files of a certain category, e.g.: album, artist or With the BLUE&ME™ media player you can play the genre. digital audio files stored on a USB device by simply connecting it to the USB port located in the center console •...
Page 100 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • To use the media player, you have to simply connect WARNING! (Continued) (directly or by an extension lead) your USB device to the • The use of any handheld device while driving is center console USB port.
Page 101: Seats
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 SEATS Forward/Rearward Adjustment Seats are a part of the Occupant Restraint System of the The adjusting bar is located at the front of the seats, near vehicle. the floor. WARNING! • It is dangerous to ride in a cargo area, inside or outside of a vehicle.
Page 102: Recline Adjustment
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE While sitting in the seat, lift up on the bar and move the Recline Adjustment seat forward or rearward. Release the bar once the The recline adjustment lever is located on the inboard desired position is reached.
Page 103: Seat Height Adjustment
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Seat Height Adjustment The driver’s seat height can be raised or lowered by using a lever, located on the outboard side of the seat.
Page 104: Memory Feature
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Memory Feature Both front seats have a memory feature, which can operate in two ways: Memory Function Option 1 — Full Seat Back And Track Fore/Aft Position Memory: After using the EZ entry function, the seatback angle and the Track fore/aft adjuster can both re-lock into the position they were most recently adjusted to.
Page 105: Heated Seats - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 Memory Function Option 2 — Seat Back Only Press the switch once to turn on the heated Memory: seats. Press the switch a second time to shut the heating elements off. After using the EZ entry function, the seat back may first be returned upright prior to going back to the last NOTE: Once a heat setting is selected, heat will be felt fore/aft (memory) position on the tracks.
Page 106: Head Restraints
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) WARNING! • Do not place anything on the seat or seatback that The head restraints for all occupants must be prop- insulates against heat, such as a blanket or cushion. erly adjusted prior to operating the vehicle or occu- This may cause the seat heater to overheat.
Page 107 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 To raise the head restraint, pull upward on the head The Reactive Head Restraints will automatically return to restraint. To lower the head restraint, press the push their normal position following a rear impact. If the button, located at the base of the head restraint, and push Reactive Head Restraints do not return to their normal downward on the head restraint.
Page 108: To Open And Close The Hood
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Head Restraints TO OPEN AND CLOSE THE HOOD To raise the head restraint, pull upward on the head re- To open the hood, two latches must be released. straint. To lower the head restraint, press the push button, 1.
Page 109 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 2. Rotate the safety catch under the front edge of the hood, near the center, and raise the hood. Hood Prop Rod In hot climates, the prop rod may be hot. Pick up the prop rod at the foam on the end of the prop rod.
Page 110: Lights
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS CAUTION! Multifunction Lever To prevent possible damage, do not slam the hood to The multifunction lever, located on the left side of the close it. Lower the hood until it is open approxi- steering wheel, controls the operation of the headlights, mately 6 in (15 cm), and then drop it.
Page 111: High Beams
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 High Beams With the low beams activated, push the multi- function lever towards the instrument panel to turn on the high beams. Pull the multifunction lever toward the steering wheel to turn off the high beams. Flash-To-Pass You can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steer-...
Page 112: Daytime Running Lights - If Equipped
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Daytime Running Lights — If Equipped To activate the Daytime Running Lights (DRL), rotate the end of the multifunction lever to the O symbol. NOTE: The low beams and side/taillights will not be on with DRL.
Page 113: Lane Change Assist
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Deactivation Lane Change Assist Tap the lever up or down once, without moving beyond Pull the multifunction lever toward the steering wheel the detent, and the turn signal (right or left) will flash and hold it for more than two seconds.
Page 114 112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When the doors are unlocked with the Key Fob a 10 CAUTION! second timer is activated. Before getting out of the vehicle be sure that the • When the doors are locked with the Key Fob the lights switch is in the center position or that the lights are will turn off.
Page 115: Front Fog Lights - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Press the switch once to turn the front fog lights on. Press Front Fog Lights — If Equipped the switch a second time to turn the front fog lights off. The fog light switch is located on the center stack of the instrument panel, just below the radio.
Page 116: Front Windshield Wiper Operation
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Wiper Off Front Windshield Wiper Operation There are five different modes of operation for the front This is the normal position of the wiper lever. windshield wipers. The windshield wiper lever can be Intermittent Wiper Operation raised or lowered to access these modes: Push the lever downward to the first detent.
Page 117 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 Manual High Speed/Mist CAUTION! Push the lever upward from the off position. The wipers • Turn the windshield wipers off when driving will operate at high speed to clear off road mist or spray through an automatic car wash.
Page 118: Rear Windshield Wiper
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Windshield Wiper Rotate the end of the windshield wiper/washer lever upward to the first detent past the intermittent settings for intermittent wipe operation. With the front wind- shield wiper active, rotate the end of the windshield wiper/washer lever upward.
Page 119: Tilt Steering Column - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 Rear Windshield Washer Operation Push the windshield wiper/washer lever toward the instrument panel to activate the rear washer. Push and hold the lever for more than a half second and the wipers will activate automatically for three cycles after the lever is released.
Page 120: Electronic Speed Control
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death.
Page 121: To Activate
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 NOTE: In order to ensure proper operation, the Elec- WARNING! tronic Speed Control system has been designed to shut down if multiple Speed Control functions are operated at Leaving the Electronic Speed Control system on the same time.
Page 122: To Deactivate
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The drivers preferred units can be selected through the To Deactivate instrument panel settings if equipped. Refer to “ Under- A soft tap on the brake pedal, pushing the CANC button, standing Your Instrument Panel” for more information. or normal brake pressure while slowing the vehicle will The speed increment shown is dependent on the selected deactivate Electronic Speed Control without erasing the...
Page 123: To Accelerate For Passing
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 • If the button is continually pressed, the set speed will • If the button is continually pressed, the set speed will continue to increase until the button is released, then continue to decrease until the button is released, then the new set speed will be established.
Page 124: Rear Park Assist - If Equipped
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using Electronic Speed Control On Hills REAR PARK ASSIST — IF EQUIPPED The transmission may downshift on hills to maintain the The Rear Park Assist system provides visual and audible vehicle set speed. indications of the distance between the rear fascia/ bumper and a detected obstacle when backing up, e.g.
Page 125: Rear Park Assist Warning Display
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 If several obstacles are detected, the Rear Park Assist Rear Park Assist Display system indicates the nearest obstacle. When the vehicle is in REVERSE, the warning display The minimum height of a detectable obstacle corresponds will turn ON indicating the system status.
Page 126: Rear Park Assist Audible Alerts
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE between the tones are directly proportional to the dis- Rear Park Assist Audible Alerts tance from the obstacle. Pulses emitted in quick succes- If an obstacle is behind the vehicle when the transmission sion indicate the presence of a very close obstacle.
Page 127: Failure Indications
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 SIGNAL MEANING INDICATION Failure Sensor or System failures Visual Signal (instrument panel) • Icon appears on display. • Message is displayed on the Electronic Vehicle Infor- mation Center (EVIC) (where provided). While audible signals are emitted, the audio system is not Failure Indications muted.
Page 128: Cleaning The Rear Park Assist System
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The sensors and wiring are tested continuously when the Park Assist System Usage Precautions ignition is in the ON/RUN position. Failures are indi- NOTE: cated immediately if they occur when the system is ON. •...
Page 129 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 • Objects such as bicycle carriers, etc., must not be CAUTION! (Continued) placed within 12 in (30 cm) from the rear fascia/ • The vehicle must be driven slowly when using bumper while driving the vehicle. Failure to do so can Rear Park Assist in order to be able to stop in time result in the system misinterpreting a close object as a when an obstacle is detected.
Page 130: Power Sunroof - If Equipped
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF — IF EQUIPPED WARNING! (Continued) The power sunroof roof switch is located in the overhead • Before using the Rear Park Assist System, it is console. strongly recommended that the ball mount and hitch ball assembly is disconnected from the ve- hicle when the vehicle is not used for towing.
Page 131: To Open
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 To Open WARNING! Press and hold the power sunroof switch rearward for • Never leave children alone in a vehicle, or with approximately one second and the sunroof will stop at access to an unlocked vehicle. Never leave the Key the vented position.
Page 132: Pinch Protect Feature
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pinch Protect Feature Emergency Operation This feature will detect an obstruction in the opening of In case of electrical failure the sunroof can be operated the sunroof during Express Close operation. If an ob- with the hex wrench that is located in the glove box.
Page 133: Electrical Power Outlets
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 Manual Sun Shade Power Outlet Power is available when the ignition switch is in the ELECTRICAL POWER OUTLETS ON/RUN or START position. Insert the cigar lighter or There is a standard 12 Volt (13 Amp) power outlet, accessory plug into the outlet for use.
Page 134 132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watts (13 Amps) power rating is exceeded, the fuse protecting the system will need to be replaced. •...
Page 135 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 WARNING! CAUTION! To avoid serious injury or death: • Many accessories that can be plugged in draw power • Only devices designed for use in this type of outlet from the vehicle’s battery, even when not in use (i.e., should be inserted into any 12 Volt outlet.
Page 136: Cigar Lighter - If Equipped
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CIGAR LIGHTER — IF EQUIPPED CUPHOLDERS This is located on the center console, in front of the cup For the driver and front passenger, cupholders are lo- holders. To activate the cigar lighter, push and release the cated on the floor console between the front seats.
Page 137: Storage
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 For rear passengers, there are cupholders located on the STORAGE floor between the front driver and passenger seats. Glove Compartment The glove compartment is located on the right side of the instrument panel. Pull outward on the glove compart- ment latch to open the glove compartment.
Page 138: Cargo Area Features
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CARGO AREA FEATURES The rear seatbacks have a fold down feature to allow increased cargo capacity. Push down the release button, located at the outboard top of the seatback and move the seatback to its folded- down position to provide a flat load floor cargo area.
Page 139: Rear Window Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 REAR WINDOW FEATURES Rear Window Defroster The rear window defroster button is located in the center of the instrument panel, below the radio. Press this button to turn on the rear window defroster. An indicator in the instrument cluster will illuminate when the rear window defroster is on.
Page 140 138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements.
Page 141: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS INSTRUMENT PANEL FEATURES ..141 ▫ Electronic Vehicle Information Center (EVIC) Setup Menu ......162 INSTRUMENT CLUSTER .
Page 142 140 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Introduction ......181 iPod®/USB/MEDIA PLAYER CONTROL — IF EQUIPPED ......207 ▫...
Page 143: Instrument Panel Features
UNDERSTANDING YOUR INSTRUMENT PANEL 141 INSTRUMENT PANEL FEATURES 1 — Side Vent 7 — Passenger Air Bag 13 — Storage Compartment 2 — Multifunction Lever – Light Control 8 — Glove Compartment 14 — Shift Lever 3 — Instrument Cluster And Warning Lights 9 —...
Page 144: Instrument Cluster
142 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER I n f o r ma t i o n P r o v i d e d b y :...
Page 145: Instrument Cluster - Eco
UNDERSTANDING YOUR INSTRUMENT PANEL 143 INSTRUMENT CLUSTER — ECO I n f o r ma t i o n P r o v i d e d b y :...
Page 146: Instrument Cluster - Pop, Lounge, 500C
144 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER — POP, LOUNGE, 500C I n f o r ma t i o n P r o v i d e d b y :...
Page 147: Instrument Cluster Descriptions
UNDERSTANDING YOUR INSTRUMENT PANEL 145 tire causes the tire to overheat and can lead to tire failure. INSTRUMENT CLUSTER DESCRIPTIONS Under-inflation also reduces fuel efficiency and tire tread 1. Tire Pressure Monitoring Telltale Light — If Equipped life, and may affect the vehicle’s handling and stopping Each tire, including the spare (if provided), ability.
Page 148 146 UNDERSTANDING YOUR INSTRUMENT PANEL When the malfunction indicator is illuminated, the sys- CAUTION! (Continued) tem may not be able to detect or signal low tire pressure equipped on your vehicle. Undesirable system opera- as intended. TPMS malfunctions may occur for a variety tion or sensor damage may result when using re- of reasons, including the installation of replacement or placement equipment that is not of the same size,...
Page 149 UNDERSTANDING YOUR INSTRUMENT PANEL 147 3. Turn Signal Indicators 4. Electronic Stability Control (ESC) Activation/ Malfunction Indicator Light The arrow will flash with the exterior turn signal when the turn signal lever is operated. The “ESC Activation/Malfunction Indicator Light” in the instrument cluster will come on when the ignition switch is turned to the NOTE: ON/RUN position.
Page 150 148 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: driving, have the system inspected at an authorized dealer as soon as possible. Refer to “Occupant Restraints” • The “ESC Off Indicator Light” and the “ESC in “Things To Know Before Starting Your Vehicle” for Activation/Malfunction Indicator Light”...
Page 151 UNDERSTANDING YOUR INSTRUMENT PANEL 149 8. Seat Belt Reminder Light testing, the light will come on when the ignition is first turned on and remain on, as a bulb check, until the When the ignition switch is first turned to engine is started.
Page 152 150 UNDERSTANDING YOUR INSTRUMENT PANEL 10. Front Fog Light Indicator — If Equipped CAUTION! This indicator will illuminate when the front Prolonged driving with the Malfunction Indicator fog lights are on. Light (MIL) on could cause damage to the engine control system.
Page 153 UNDERSTANDING YOUR INSTRUMENT PANEL 151 14. Brake Warning Light CAUTION! This light monitors various brake functions, Failure to follow these cautions can cause damage to including brake fluid level and parking brake the heating elements: application. If the brake light turns on it may •...
Page 154 152 UNDERSTANDING YOUR INSTRUMENT PANEL The dual brake system provides a reserve braking capac- WARNING! ity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is Driving a vehicle with the red brake light on is indicated by the Brake Warning Light, which will turn on dangerous.
Page 155 UNDERSTANDING YOUR INSTRUMENT PANEL 153 Operation of the Brake Warning Light can be checked by 15. Anti-Lock Brake (ABS) Light turning the ignition switch from the OFF position to the This light monitors the Anti-lock Brake System ON/RUN position. The light should illuminate for ap- (ABS).
Page 156 154 UNDERSTANDING YOUR INSTRUMENT PANEL 16. Gas Pedal Percentage Gauge/Turbo Gauge/ frequent accelerations/decelerations and will de- ECO Index Gauge crease your fuel economy. The index is recalculated approximately every second and takes into account a Depending on what options and trim level your vehicle is combination of the instant fuel economy and your equipped with there are three gauges available.
Page 157 UNDERSTANDING YOUR INSTRUMENT PANEL 155 18. Electronic Vehicle Information Center (EVIC) CAUTION! The EVIC features a driver-interactive display that is Driving with a hot engine cooling system could damage located in the instrument cluster. For further information, your vehicle. If the temperature gauge reads “H” pull refer to “Electronic Vehicle Information Center (EVIC)”...
Page 158 156 UNDERSTANDING YOUR INSTRUMENT PANEL 20. Tachometer before the repair or service. It is a good idea for you to make a record of the odometer reading before the repair/ The tachometer indicates engine speed in Revolutions service, so that you can be sure that it is properly reset, or Per Minute (RPM x 1000).
Page 159 UNDERSTANDING YOUR INSTRUMENT PANEL 157 23. Generic Warning Light 25. Charging System Light The Generic Warning Light will illuminate if This light shows the status of the electrical charg- any of the following conditions occur: Oil ing system. The light should come on when the Change Request, Engine Oil Pressure Sensor ignition switch is first turned to ON/RUN and remain on Failure, External Light Failure, Fuel Cut-Off...
Page 160 158 UNDERSTANDING YOUR INSTRUMENT PANEL 26. Electronic Throttle Control (ETC) Light 27. Oil Pressure Warning Light This light informs you of a problem with the This light indicates low engine oil pressure. The Electronic Throttle Control (ETC) system. If a light should turn on momentarily when the engine is problem is detected, the light will come on started.
Page 161: Electronic Vehicle Information Center (Evic)
UNDERSTANDING YOUR INSTRUMENT PANEL 159 If the light turns on while driving, safely pull over and ELECTRONIC VEHICLE INFORMATION stop the vehicle. If the A/C system is on, turn it off. Also, CENTER (EVIC) shift the transmission into NEUTRAL and idle the ve- The Electronic Vehicle Information Center (EVIC) fea- hicle.
Page 162: Evic Displays
160 UNDERSTANDING YOUR INSTRUMENT PANEL The EVIC consists of the following: EVIC Displays • System Status • Vehicle Information Warning Message Displays • Personal Settings (Customer-Programmable Features) • Outside Temperature Display • Trip Computer Functions • Tire Pressure Monitoring Display Instrument Cluster 1.
Page 163: Evic Control Buttons
UNDERSTANDING YOUR INSTRUMENT PANEL 161 • Door Ajar 5. Red Telltales (Right Bank) • Speed Limiter — If Equipped • Trunk Ajar • Transmission Failure 2. Amber Telltales • Battery Charge Indicator • Ice Risk • Fuel Cut Off 6. Exceeded Speed Limiter •...
Page 164: Electronic Vehicle Information Center (Evic) Setup Menu
162 UNDERSTANDING YOUR INSTRUMENT PANEL Push and release the DOWN button to scroll down- Electronic Vehicle Information Center (EVIC) ward through the displayed menu and the related Setup Menu options or to decrease the value displayed. The menu comprises a series of functions arranged in a NOTE: UP and DOWN buttons activate differ-...
Page 165 UNDERSTANDING YOUR INSTRUMENT PANEL 163 • See Radio Selecting An Option Of The Main Menu Without Submenu • Speed Display 1. Briefly push and release the MENU button to select • Autoclose the main menu option to set. • Units 2.
Page 166: Change Engine Oil Indicator System
164 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Briefly push and release the MENU button to select after a single chime has sounded to indicate the next the displayed submenu option and to open the rel- scheduled oil change interval. The engine oil change evant setup menu.
Page 167: Trip Computer
UNDERSTANDING YOUR INSTRUMENT PANEL 165 NOTE: If the indicator message illuminates when you New Trip start the vehicle, the oil change indicator system did not To reset: reset. If necessary, repeat this procedure. • Push and hold the TRIP button to reset the system Trip Computer manually.
Page 168: Trip Functions
166 UNDERSTANDING YOUR INSTRUMENT PANEL Start Of Trip Procedure • Average consumption With the ignition on, push and hold the TRIP button for • Instantaneous consumption over one second to reset. • Average speed A Exit Trip • Travel time A (driving time) To exit the Trip function, wait until all the values have been “Trip B”...
Page 169: Values Displayed
UNDERSTANDING YOUR INSTRUMENT PANEL 167 Average Economy Values Displayed This value shows the approximate average consumption Range since the last reset. This indicates the distance which may be traveled with the fuel remaining in the tank, assuming that driving Instant Economy conditions will not change.
Page 170: Personal Settings (Customer-Programmable Features)
168 UNDERSTANDING YOUR INSTRUMENT PANEL Speed Beep (Speed Limit) Personal Settings (Customer-Programmable Features) With this function, it is possible to set the car speed limit Dimmer (mph or km/h) to immediately alert the driver when the The EVIC display is provided with a light sensor capable set limit is exceeded.
Page 171 UNDERSTANDING YOUR INSTRUMENT PANEL 169 NOTE: The setting can be increased or decreased by 3. Briefly push and release the MENU button to go back 5 mph or km/h each time the UP/DOWN button is to the menu screen, or push and hold the MENU pushed for speed settings above 20 mph (32 km/h).
Page 172 170 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Briefly push and release the MENU button to go back 4. When accessing the “Time” sub-menu item, briefly to the menu screen, or push and hold the MENU push and release the MENU button and “hours” will button (approximately one second) to go back to the flash on the display.
Page 173 UNDERSTANDING YOUR INSTRUMENT PANEL 171 • Briefly push and release the MENU button to return To change the date proceed as follows: to the “Time” sub-function. 1. Briefly push and release the MENU button. Push and • When accessing the “Mode” submenu, briefly push release the UP or DOWN button to highlight...
Page 174 172 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The setting will increase or decrease by one unit To activate (On) or to deactivate (Off) the sound system each time the UP or DOWN button is pushed. info displaying proceed as follows: Push and hold the UP or DOWN button to 1.
Page 175 UNDERSTANDING YOUR INSTRUMENT PANEL 173 Speed Display Autoclose When this function is activated the cluster will display With this function active, the doors will automatically the vehicle speed (MPH or km/h). lock at when the vehicle’s speed exceeds 15 mph (24 km/h).
Page 176 174 UNDERSTANDING YOUR INSTRUMENT PANEL Units (Set Units) 5. Push and release the UP or DOWN button for setting. This function may be used to set the measurement unit in three submenus: “Distance,” “Temperature” and “Fuel 6. Briefly push and release the MENU button to return to Economy, and Tire Pressure.”...
Page 177 UNDERSTANDING YOUR INSTRUMENT PANEL 175 3. When accessing the “Temperature” submenu: briefly Language (Selecting The Language) push and release the MENU button. Either “°F” or The messages can be displayed in the following lan- “°C” will appear on the display (according to the guages: Italian, English, Turkce, Nederlands, Spanish, previous setting).
Page 178 176 UNDERSTANDING YOUR INSTRUMENT PANEL Buzzer Volume (Adjusting The Failure/Warning Button Volume (Button Volume Adjustment) Buzzer Volume) This function may be used to adjust the volume of the With this function the volume of the buzzer accompany- beep accompanying the buttons. MENU, UP ing any failure/warning indication can be adjusted to DOWN buttons can be adjusted according to...
Page 179 DOWN button for setting. This function will only be displayed after a FIAT Group Automobiles dealership has deactivated the S.B.R. system. 4. Briefly push and release the MENU button to go back to the menu screen, or push and hold the button...
Page 180 178 UNDERSTANDING YOUR INSTRUMENT PANEL To set the required unit, proceed as follows: Hill Start Assist This function is used when starting a vehicle from a stop 1. Briefly push and release the MENU button to display on a hill. Hill Start Assist maintains the same level of the two sub-menus.
Page 181 UNDERSTANDING YOUR INSTRUMENT PANEL 179 Tire Pressure Lock This function will be used to display the tire pressures When Unlock Driver Door is selected, only the driver’s individually for all four tires by location. door will unlock on the first push of the Remote Keyless Entry (RKE) transmitter UNLOCK button.
Page 182: Sales Code (Rab) Radio
180 UNDERSTANDING YOUR INSTRUMENT PANEL Exit Menu SALES CODE (RAB) RADIO This function closes the initial menu screen. Briefly push and release the MENU button to go back to the main screen. Push and release the button to return to the first menu option (Speed Beep).
Page 183: Introduction
UNDERSTANDING YOUR INSTRUMENT PANEL 181 Reception Conditions Introduction The radio has been designed according to the specifica- Reception conditions change constantly while driving. tions of the passenger compartment, with a personalized Reception may be interfered with by the presence of design to match the style of the dashboard.
Page 184 182 UNDERSTANDING YOUR INSTRUMENT PANEL • Do not stick labels on the CD surface or write on the recorded surface with pencils or pens. The presence of dirt, scratches or distortions on the CDs could cause skipping and poor sound quality while it is •...
Page 185: Technical Specifications
UNDERSTANDING YOUR INSTRUMENT PANEL 183 • If a copy-protected CD is used, it may take a few Technical Specifications seconds before the system starts to play it. The CD The complete system consists of: player cannot be guaranteed to play all protected •...
Page 186: Quick Guide
184 UNDERSTANDING YOUR INSTRUMENT PANEL With Alpine Premium Audio system (if equipped): • Antenna on the car roof. • Two 165 mm diameter midwoofer speakers. • Radio with CD/MP3 player. With BEATS Premium Audio system (if equipped): • Two 11 mm tweeter speakers in the front pillars. •...
Page 187 UNDERSTANDING YOUR INSTRUMENT PANEL 185 BUTTON GENERAL FUNCTIONS MODE MEDIA CD/AUX/Media Player (if equipped and Short repeated button push present) source selection BUTTON GENERAL FUNCTIONS MODE (Mute/Pause Button) Volume activation/deactivation Short button push (Mute/Pause) AUDIO Audio adjustments: tones Menu activation: short button push (BASS), high tones (TREBLE), left/ Adjustment type selection: push right balance (BALANCE), front/...
Page 188 186 UNDERSTANDING YOUR INSTRUMENT PANEL BUTTON GENERAL FUNCTIONS MODE MENU Advanced functions adjustment Menu activation: short button push Adjustment type selection: push Adjustment of values: push +Vol/–Vol Volume adjustment Push + button: volume increase Push – button: volume decrease BUTTON RADIO FUNCTIONS MODE Radio Station Search:...
Page 189: General Information
UNDERSTANDING YOUR INSTRUMENT PANEL 187 BUTTON CD FUNCTIONS MODE CD ejection Short button push Previous/next track play Short button push CD track fast forward/rewind Long button push Previous/next folder play Short button push (for CD-MP3) • Manual storing of 25 stations (base radio) and 40 General Information stations (if equipped with Satellite): 15 on FM band The radio offers the following functions:...
Page 190 188 UNDERSTANDING YOUR INSTRUMENT PANEL CD Section • Track selection (forward/backward) • Track selection (forward/backward) • Fast forward/rewind through tracks • Fast forward/rewind through tracks • MP3 Display function: display of folder name, ID3-TAG information, time elapsed since the start of •...
Page 191: Functions And Adjustments
UNDERSTANDING YOUR INSTRUMENT PANEL 189 Selecting The CD Function Functions And Adjustments By briefly pushing the MEDIA button, the CD audio Turning The Car Radio On source can be selected (only if a CD is loaded). The car radio comes on when the (ON/OFF) button is pushed briefly.
Page 192 190 UNDERSTANDING YOUR INSTRUMENT PANEL When the volume level is changed using the dedicated The current status of the selected function appears on the controls, the Mute function is deactivated and the vol- display. ume is adjusted to the new level selected. The functions managed by the Audio Menu are: Audio Adjustment •...
Page 193 UNDERSTANDING YOUR INSTRUMENT PANEL 191 Tone Adjustment Balance Adjustment Proceed as follows: Proceed as follows: 1. Push the AUDIO button. 1. Push the AUDIO button. 2. Push the button to select “Bass,” “Mid- 2. Push the button to set “Balance” in the range”...
Page 194 192 UNDERSTANDING YOUR INSTRUMENT PANEL Fader Adjustment Loudness Function — If Equipped Proceed as follows: The Loudness function improves the volume of the sound while listening at low volumes, increasing the bass 1. Push the AUDIO button. and treble. 2. Push the button to set “Fader”...
Page 195 UNDERSTANDING YOUR INSTRUMENT PANEL 193 To activate the equalizer, use the AUDIO button to select User EQ Settings Function — If Equipped one of the adjustments: To set a personalized equalizer adjustment: • “EQ User” (adjustment of 7 equalizer bands that can 1.
Page 196 194 UNDERSTANDING YOUR INSTRUMENT PANEL Menu • System Reset MENU Button Functions • Speed Volume Push the MENU button briefly to activate the Menu • On Volume Limit function. Push the MENU button again to exit the Menu function. Use the buttons to scroll through the menu Speed Volume Function —...
Page 197 UNDERSTANDING YOUR INSTRUMENT PANEL 195 On Volume Limit • “On volume limit: off” – The radio will come on at the same volume as before it was switched off. The This function makes it possible to activate/deactivate the volume level can be between 0 and 40. maximum volume limit when turning the radio on.
Page 198: Radio
196 UNDERSTANDING YOUR INSTRUMENT PANEL Radio Off Function System Reset Function This function makes it possible to set the radio switching This function is used to restore all settings to the factory off mode by choosing between two methods. values. The options are: The chosen mode appears on the display: •...
Page 199 UNDERSTANDING YOUR INSTRUMENT PANEL 197 Once the Radio mode has been activated, the display will Preset Buttons show the name (RBDS stations only) or the frequency of The buttons numbered from 1 to 5 are used to set the the selected radio station, the frequency band selected following pre-selections: (e.g.
Page 200: Siriusxm Satellite Radio - If Equipped
198 UNDERSTANDING YOUR INSTRUMENT PANEL Automatic Tuning Stereophonic Broadcasters Briefly push the button to start the automatic If the incoming signal is weak, the reproduction is tuning search for the next station that can be received automatically switched from Stereo to Mono. in the selected direction.
Page 201 UNDERSTANDING YOUR INSTRUMENT PANEL 199 logos are trademarks of SiriusXM Radio Inc. and its subsid- The Program Types available are: All, Pop, Rock, iaries. SiriusXM Radio requires a subscription, sold sepa- Electronic/Dance, Hip-Hop/R&B, Country, Christian, rately after trial subscription included with vehicle pur- Jazz/Standards, Classical, Latin/World, Sports, Enter- chase.
Page 202 Sirius Subscription Issues When Replacing A CAUTION! Sirius Radio Neither SIRIUS nor FIAT is responsible for any When a radio needs to be replaced, the Dealer will need errors in accuracies in the SIRIUS data services or its the SIRIUS information to order a new radio (even if the use in vehicles.
Page 203: Cd Player
UNDERSTANDING YOUR INSTRUMENT PANEL 201 The following are instructions for retrieving the Elec- CD Player tronic Serial Number (ESN) from FIAT 500 NAFTA model Introduction radios: This chapter describes the operation of the CD player To retrieve the ESN of SIRIUS Satellite Receiver Module only.
Page 204 202 UNDERSTANDING YOUR INSTRUMENT PANEL It is advisable to use original CDs to ensure optimal Push the button with the radio turned on, to playing. If CD-R/RWs are used, we recommend using activate the motorized CD ejection system. After ejec- good quality media that are burned at the slowest speed tion, the last audio source listened to before playing possible.
Page 205 UNDERSTANDING YOUR INSTRUMENT PANEL 203 A CD which cannot be read will not be ejected until these If the track has been played for more than 3 seconds, functions are over. At the end, with the CD mode pushing the button, starts the track again from the activated, the display will show the wording “CD Disc beginning.
Page 206: Cd Mp3 Player
204 UNDERSTANDING YOUR INSTRUMENT PANEL The specifications and operating conditions for playing CD MP3 Player MP3 files are the following: Introduction • The CD-ROMs used should be burned in accordance This chapter describes the operation of the CD MP3 with ISO standard 9660. player.
Page 207 UNDERSTANDING YOUR INSTRUMENT PANEL 205 Selecting MP3 Sessions With Hybrid Discs When one of the ID3-TAG pieces of information is chosen to be displayed (Title, Artist, Album) and this informa- If a hybrid disc is inserted (Mixed Mode, Enhanced, tion has not been recorded for the track played, the text CD-Extra) also containing MP3 files, the radio automati- UNKNOWN will be displayed for that field.
Page 208: Troubleshooting
206 UNDERSTANDING YOUR INSTRUMENT PANEL Structure Of The Folders Source Can Not Be Selected The radio with MP3 player: Nothing has been loaded. Load the CD or the MP3 CD to be listened to. • Recognizes only the folders that effectively contain MP3 format files.
Page 209: Ipod®/Usb/Media Player Control - If
UNDERSTANDING YOUR INSTRUMENT PANEL 207 The Duration Of The Mp3 Tracks Is Not Correctly Displayed: In some cases (due to the recording mode) the duration of the MP3 tracks can be displayed incorrectly. Operating Instructions — Hands-Free Phone Refer to the appropriate “BLUE&ME™ User’s Manual” for further information.
Page 210: Steering Wheel Audio Controls
208 UNDERSTANDING YOUR INSTRUMENT PANEL The right-hand control is a rocker-type switch with a STEERING WHEEL AUDIO CONTROLS pushbutton in the center and controls the volume and The remote sound system controls are located on the rear mode of the sound system. Pushing the top of the rocker surface of the steering wheel.
Page 211: Radio Operation
UNDERSTANDING YOUR INSTRUMENT PANEL 209 Radio Operation Operating Instructions — Hands-Free Phone (If Equipped) Pushing the top of the switch will “Seek” up for the next listenable station and pushing the bottom of the switch Refer to the appropriate Blue&Me™ User’s Manual for will “Seek”...
Page 212: Radio Operation And Mobile Phones
210 UNDERSTANDING YOUR INSTRUMENT PANEL 4. Do not use solvents such as benzene, thinner, cleaners, RADIO OPERATION AND MOBILE PHONES or anti-static sprays. Under certain conditions, the mobile phone being on in your vehicle can cause erratic or noisy performance from 5.
Page 213: Manual Heating And Air Conditioning
UNDERSTANDING YOUR INSTRUMENT PANEL 211 1. Temperature Control Manual Heating And Air Conditioning Rotate this control to regulate the temperature of the air inside the passenger compartment. Rotating the dial to the left into the blue area of the scale indicates cooler temperatures, while rotating to the right into the red area indicates warmer temperatures.
Page 214 212 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • Panel Air is directed through the outlets in the • Continuous use of the Recirculation mode may make instrument panel. These outlets can be ad- the inside air stuffy and window fogging may occur. justed to direct airflow.
Page 215: Automatic Temperature Control (Atc)
UNDERSTANDING YOUR INSTRUMENT PANEL 213 require extra heat to the windshield. This setting is MAX A/C good for maintaining comfort while reducing mois- For maximum cooling, use the A/C and recirculation ture on the windshield. modes at the same time. •...
Page 216 214 UNDERSTANDING YOUR INSTRUMENT PANEL The ATC system automatically maintains the interior between manual mode and automatic modes. Refer to comfort level desired by the occupant. “Automatic Operation” for more information. 2. A/C Button Push and release to change the current Air Conditioning (A/C) setting.
Page 217 UNDERSTANDING YOUR INSTRUMENT PANEL 215 The blower fan speed may be set to any fixed speed by 6. Front Defrost pushing the blower control up or down buttons. The fan Push and release to change the current airflow will now operate at a fixed speed until additional speeds setting to Defrost mode.
Page 218 216 UNDERSTANDING YOUR INSTRUMENT PANEL 8. Panel Mode 10. Temperature Control Down Button Air is directed through the outlets in the instru- Provides temperature down control. Push the button for ment panel. These outlets can be adjusted to direct cooler temperature settings. airflow.
Page 219 UNDERSTANDING YOUR INSTRUMENT PANEL 217 Climate Control Functions Recirculation Control When outside air contains smoke, odors, or high Air Conditioning (A/C) humidity, or if rapid cooling is desired, you may The Air Conditioning (A/C) button allows the operator wish to recirculate interior air by pushing the RECIRCU- to manually activate or deactivate the air conditioning LATION control button.
Page 220 218 UNDERSTANDING YOUR INSTRUMENT PANEL Automatic Operation NOTE: 1. Push the AUTO button on the Automatic Temperature • It is not necessary to move the temperature settings for Control (ATC) Panel, the indicator will illuminate cold or hot vehicles. The system automatically adjusts when on.
Page 221: Operating Tips
UNDERSTANDING YOUR INSTRUMENT PANEL 219 Manual Operation Window Fogging The system allows for manual selection of blower speed, Windows will fog on the inside when the humidity inside air distribution mode, A/C status and recirculation con- the vehicle is high. This often occurs in mild or cool trol.
Page 222 220 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Automatic Temperature Controls (ATC) will au- Winter Operation tomatically adjust the climate control settings to reduce When operating the system during the winter months, or eliminate window fogging on the front windshield. make sure the air intake, located directly in front of the When this occurs, recirculation will be unavailable.
Page 223 UNDERSTANDING YOUR INSTRUMENT PANEL 221 Operating Tips Chart I n f o r ma t i o n P r o v i d e d b y :...
Page 224 I n f o r ma t i o n P r o v i d e d b y :...
Page 225: Starting And Operating
STARTING AND OPERATING CONTENTS STARTING PROCEDURES ....227 ▫ Five-Speed Manual Transmission...230 ▫ Manual Transmission — If Equipped ..227 ▫...
Page 226 224 STARTING AND OPERATING ▫ Operation ......242 ELECTRONIC BRAKE CONTROL SYSTEM ..252 DRIVING ON SLIPPERY SURFACES .
Page 227 STARTING AND OPERATING 225 TIRES — GENERAL INFORMATION ..273 TIRE ROTATION RECOMMENDATIONS ..287 ▫ Tire Pressure ......273 TIRE PRESSURE MONITORING SYSTEM (TPMS) .
Page 228 226 STARTING AND OPERATING ▫ Materials Added To Fuel ....301 ▫ Loose Fuel Filler Cap Message ... .305 ▫...
Page 229: Starting Procedures
STARTING AND OPERATING 227 STARTING PROCEDURES Manual Transmission — If Equipped Before starting your vehicle, adjust your seat, adjust both Apply the parking brake, place the shift lever in NEU- inside and outside mirrors, and fasten your seat belts. TRAL, and press the clutch pedal before starting the vehicle.
Page 230: Normal Starting
228 STARTING AND OPERATING The message “plug in engine heater” will be displayed in Normal Starting the instrument cluster when the ambient temperature is NOTE: Normal starting of either a cold or a warm below 5° F (–15° C) at the time the engine is shut off as a engine is obtained without pumping or pressing the reminder to avoid possible crank delays at the next cold accelerator pedal.
Page 231: If Engine Fails To Start
STARTING AND OPERATING 229 2. Cycle the ignition in the START position and release it If Engine Fails To Start when the engine starts. WARNING! 3. If the engine fails to start within ten seconds, cycle the ignition to the STOP (OFF/LOCK) position, wait five Never pour fuel or other flammable liquids into the seconds to allow the starter to cool, then repeat the throttle body air inlet opening in an attempt to start...
Page 232: After Starting
230 STARTING AND OPERATING MANUAL TRANSMISSION — IF EQUIPPED CAUTION! (Continued) Five-Speed Manual Transmission • To prevent damage to the starter, do not continu- ously crank the engine for more than 15 seconds at WARNING! a time. Wait 10 to 15 seconds before trying again. You or others could be injured if you leave the After Starting vehicle unattended without having the parking...
Page 233 STARTING AND OPERATING 231 Use each gear in numerical order; do not skip a gear. Be sure the transmission is in first gear, not third, when starting from a standing position. Damage to the clutch can result from starting in third gear. For most city driving, you will find it easier to use only the lower gears.
Page 234: Recommended Shift Speeds
232 STARTING AND OPERATING NOTE: Recommended Shift Speeds To use your manual transmission for optimal fuel • Clashing REVERSE gear, especially if vehicle is mov- economy, it should be upshifted as listed in the following ing, can result in transmission damage. table.
Page 235: Downshifting
STARTING AND OPERATING 233 Downshifting AUTOMATIC TRANSMISSION — IF EQUIPPED Proper downshifting will improve fuel economy and CAUTION! prolong engine life. Damage to the transmission may occur if the follow- CAUTION! ing precautions are not observed: • Shift into or out of PARK or REVERSE only after If you skip a gear while downshifting or downshift the vehicle has come to a complete stop.
Page 236 234 STARTING AND OPERATING WARNING! WARNING! (Continued) locked in PARK, securing the vehicle against un- • It is dangerous to shift out of PARK or NEUTRAL wanted movement. if the engine speed is higher than idle speed. If • When leaving the vehicle, always remove the igni- your foot is not firmly pressing the brake pedal, the tion key from the vehicle and lock the vehicle.
Page 237: Key Ignition Park Interlock
STARTING AND OPERATING 235 Key Ignition Park Interlock Six-Speed Automatic Transmission This vehicle is equipped with a Key Ignition Park Inter- The transmission gear position display (located in the lock which requires the transmission to be in PARK instrument cluster) indicates the transmission gear range. before the ignition switch can be turned to the LOCK/ You must press the brake pedal to move the shift lever OFF (key removal) position.
Page 238 236 STARTING AND OPERATING The transmission shift lever has PARK, REVERSE, NEU- TRAL, DRIVE, and AutoStick shift positions. Manual shifts can be made using the AutoStick shift control (refer to “AutoStick” in this section for further information). Toggling the shift lever forward (-) or rearward (+) while in the AutoStick position (beside the DRIVE position) will manually select the transmission gear, and will display the current gear in the instrument cluster as 1, 2,...
Page 239: Gear Ranges
STARTING AND OPERATING 237 When parking on a hill, apply the parking brake before Gear Ranges shifting the transmission to PARK, otherwise the load on the DO NOT race the engine when shifting from PARK or transmission locking mechanism may make it difficult to NEUTRAL into another gear range.
Page 240 238 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • It is dangerous to shift out of PARK or NEUTRAL locked in PARK, securing the vehicle against un- if the engine speed is higher than idle speed. If wanted movement. your foot is not firmly pressing the brake pedal, the •...
Page 241 STARTING AND OPERATING 239 • Look at the transmission gear position display and CAUTION! verify that it indicates the PARK position. • Before moving the shift lever out of PARK, you • With brake pedal released, verify that the shift lever must turn the ignition switch from the LOCK/OFF will not move out of PARK.
Page 242 240 STARTING AND OPERATING DRIVE (D) WARNING! This range should be used for most city and highway Do not coast in NEUTRAL and never turn off the driving. It provides the smoothest upshifts and down- ignition to coast down a hill. These are unsafe shifts, and the best fuel economy.
Page 243 STARTING AND OPERATING 241 If the transmission temperature exceeds normal operating Limp Home Mode allows the vehicle to be driven to an authorized dealer for service without damaging the trans- limits, the transmission controller will expand the range of mission. torque converter clutch engagement.
Page 244: Autostick
242 STARTING AND OPERATING NOTE: Even if the transmission can be reset, we recom- Operation mend that you visit your authorized dealer at your When the shift lever is in the AutoStick position (beside earliest possible convenience. Your authorized dealer has the Drive position), it can be moved forward and rear- diagnostic equipment to determine if the problem could ward.
Page 245 STARTING AND OPERATING 243 • The transmission will automatically downshift to first • Transmission shifting will be more noticeable when gear when coming to a stop. After a stop, the driver AutoStick is engaged. should manually upshift (+) the transmission as the •...
Page 246: Driving On Slippery Surfaces
244 STARTING AND OPERATING DRIVING ON SLIPPERY SURFACES Traction When driving on wet or slushy roads, it is possible for a Acceleration wedge of water to build up between the tire and road Rapid acceleration on snow covered, wet, or other slip- surface.
Page 247: Driving Through Water
STARTING AND OPERATING 245 DRIVING THROUGH WATER Shallow Standing Water Driving through water more than a few inches/ Although your vehicle is capable of driving through centimeters deep will require extra caution to ensure shallow standing water, consider the following Cautions safety and prevent damage to your vehicle.
Page 248 246 STARTING AND OPERATING CAUTION! CAUTION! (Continued) • Driving through standing water may cause damage • Always check the depth of the standing water to your vehicle’s drivetrain components. Always before driving through it. Never drive through inspect your vehicle’s fluids (i.e., engine oil, trans- standing water that is deeper than the bottom of mission, axle, etc.) for signs of contamination (i.e., the tire rims mounted on the vehicle.
Page 249: Power Steering
STARTING AND OPERATING 247 If the Steering icon is displayed and the “SERVICE POWER STEERING POWER STEERING” message is displayed on the EVIC The electric power steering system will give you good screen, they indicate that extreme steering maneuvers vehicle response and increased ease of maneuverability may have occurred which caused an over temperature in tight spaces.
Page 250: Parking Brake
248 STARTING AND OPERATING NOTE: • Even if the power steering assistance is no longer operational, it is still possible to steer the vehicle. Under these conditions there will be a substantial increase in steering effort, especially at low speeds and during parking maneuvers.
Page 251 STARTING AND OPERATING 249 When parking on a hill, it is important to turn the front WARNING! (Continued) wheels toward the curb on a downhill grade and away • Do not leave the Key Fob in or near the vehicle or from the curb on an uphill grade.
Page 252: Sport Mode
250 STARTING AND OPERATING CAUTION! If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated. Have the brake system serviced by an authorized dealer immediately. SPORT MODE Manual Transmission — If Equipped The Sport mode increases steering feedback to the driver with slight increases in effort and throttle pedal-to-engine SPORT Button...
Page 253: Automatic Transmission - If Equipped
STARTING AND OPERATING 251 Automatic Transmission — If Equipped The Sport mode increases steering feedback to the driver with slight increase in effort and changes the transmis- sion shift schedules for more aggressive shifting. This driving mode is useful while driving on twisty roads where more steering precision is desired in spirited cornering.
Page 254: Brake System
252 STARTING AND OPERATING BRAKE SYSTEM ELECTRONIC BRAKE CONTROL SYSTEM Your vehicle is equipped with dual hydraulic brake Your vehicle is equipped with a advanced electronic systems. If either of the two hydraulic systems loses brake control system that includes the Anti-Lock Brake normal capability, the remaining system will still func- System (ABS), Brake Assist System (BAS), Traction Con- tion.
Page 255 STARTING AND OPERATING 253 The ABS includes an amber ABS Warning Light. When WARNING! (Continued) the light is illuminated, the ABS is not functioning. The • The ABS cannot prevent collisions, including those system reverts to standard non-anti-lock brakes. Turning resulting from excessive speed in turns, following the ignition Off and On again may reset the ABS if the another vehicle too closely, or hydroplaning.
Page 256: Brake Assist System (Bas)
254 STARTING AND OPERATING Brake Assist System (BAS) WARNING! The BAS is designed to optimize the vehicle’s braking • The Brake Assist System (BAS) cannot prevent the capability during emergency braking maneuvers. The natural laws of physics from acting on the vehicle, system detects an emergency braking situation by sens- nor can it increase the traction afforded by prevail- ing the rate and amount of brake application and then...
Page 257: Traction Control System (Tcs)
STARTING AND OPERATING 255 Traction Control System (TCS) Hill Start Assist (HSA) This system monitors the amount of wheel spin of each of The HSA system is designed to assist the driver when the driven wheels. If wheel spin is detected, brake starting a vehicle from a stop on a hill.
Page 258 256 STARTING AND OPERATING HSA Activation Criteria WARNING! (Continued) The following criteria must be met in order for HSA to could cause a collision with another vehicle or object. activate: Always remember the driver is responsible for brak- ing the vehicle. •...
Page 259: Electronic Stability Control (Esc)
STARTING AND OPERATING 257 Electronic Stability Control (ESC) The Electronic Stability Control (ESC) system enhances directional control and stability of the vehicle under various driving conditions. ESC corrects for oversteering or understeering of the vehicle by applying the brake of the appropriate wheel to assist in counteracting the oversteering or understeering condition.
Page 260 258 STARTING AND OPERATING WARNING! The Electronic Stability Control (ESC) cannot pre- vent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. ESC cannot prevent all accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning.
Page 261 STARTING AND OPERATING 259 ESC Operating Modes NOTE: To improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand or The ESC system has two available operating modes. gravel, it may be desirable to switch to the Partial Off Full On mode by pressing the switch.
Page 262: Esc Activation/Malfunction Indicator Light And Esc Off Indicator Light
260 STARTING AND OPERATING The ESC Activation/Malfunction Indicator Light also ESC Activation/Malfunction Indicator Light And flashes when TCS is active. If the ESC Activation/ ESC OFF Indicator Light Malfunction Indicator Light begins to flash during accel- eration, ease up on the accelerator and apply as little The ESC Activation/Malfunction Indicator throttle as possible.
Page 263: Tire Safety Information
STARTING AND OPERATING 261 NOTE: TIRE SAFETY INFORMATION • P (Passenger) — Metric tire sizing is based on U.S. Tire Markings design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. •...
Page 264 262 STARTING AND OPERATING • Temporary spare tires are designed for temporary • High flotation tire sizing is based on U.S. design emergency use only. Temporary high pressure com- standards and it begins with the tire diameter molded pact spare tires have the letter “T” or “S” molded into into the sidewall.
Page 265 STARTING AND OPERATING 263 EXAMPLE: 65, 85, 80 = Aspect ratio in percent (%) – Ratio of section height to section width of tire, or 10.5 = Section width in inches (in) R = Construction code – R means radial construction, or –...
Page 266 264 STARTING AND OPERATING EXAMPLE: H = Speed Symbol – A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions – The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e., tire pressure, vehicle loading, road conditions, and posted speed limits) Load Identification:...
Page 267: Tire Identification Number (Tin)
STARTING AND OPERATING 265 Look for the TIN on the outboard side of black sidewall Tire Identification Number (TIN) tires as mounted on the vehicle. If the TIN is not found on The TIN may be found on one or both sides of the tire, the outboard side, then you will find it on the inboard however, the date code may only be on one side.
Page 268: Tire Terminology And Definitions
266 STARTING AND OPERATING EXAMPLE: DOT MA L9 ABCD 0301 01 = Number representing the year in which the tire was manufactured (two digits) – 01 means the year 2001 – Prior to July 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured.
Page 269 STARTING AND OPERATING 267 Term Definition Maximum Inflation Pressure The maximum inflation pressure is the maximum permissible cold tire inflation pressure for this tire. The maximum inflation pressure is molded into the sidewall. Recommended Cold Tire Inflation Vehicle manufacturer’s recommended cold tire inflation pressure Pressure as shown on the tire placard.
Page 270: Tire Loading And Tire Pressure
268 STARTING AND OPERATING Tire Loading And Tire Pressure Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door. Example Tire Placard Location (B-Pillar) Example Tire Placard Location (Door) I n f o r ma t i o n P r o v i d e d b y :...
Page 271 STARTING AND OPERATING 269 Tire And Loading Information Placard This placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4.
Page 272 270 STARTING AND OPERATING NOTE: Under a maximum loaded vehicle condition, Steps For Determining Correct Load Limit gross axle weight ratings (GAWRs) for the front and rear 1. Locate the statement “The combined weight of occu- axles must not be exceeded. For further information on pants and cargo should never exceed XXX lbs or GAWRs, vehicle loading, and trailer towing, refer to XXX kg”...
Page 273 STARTING AND OPERATING 271 4. The resulting figure equals the available amount of NOTE: cargo and luggage load capacity. For example, if • If your vehicle will be towing a trailer, load from your “XXX” amount equals 1,400 lbs (635 kg) and there will trailer will be transferred to your vehicle.
Page 274 272 STARTING AND OPERATING I n f o r ma t i o n P r o v i d e d b y :...
Page 275: Tires - General Information
STARTING AND OPERATING 273 Safety WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase • Improperly inflated tires are dangerous and can your stopping distance. Use tires of the recommended cause collisions. load capacity for your vehicle.
Page 276 274 STARTING AND OPERATING Economy WARNING! (Continued) Underinflated tires will increase tire rolling resistance • Unequal tire pressures from one side of the vehicle resulting in higher fuel consumption. to the other can cause the vehicle to drift to the right or left.
Page 277: Tire Inflation Pressures
STARTING AND OPERATING 275 Inflation pressures specified on the placard are always Tire Inflation Pressures “cold tire inflation pressure.” Cold tire inflation pressure is The proper cold tire inflation pressure is listed on the defined as the tire pressure after the vehicle has not been driver’s side B-Pillar or rear edge of the driver’s side door.
Page 278: Tire Pressures For High Speed Operation
276 STARTING AND OPERATING Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) WARNING! during operation. DO NOT reduce this normal pressure build up or your tire pressure will be too low. High speed driving with your vehicle under maxi- mum load is dangerous.
Page 279: Tire Types
STARTING AND OPERATING 277 Tire Repair Tire Types If your tire becomes damaged, it may be repaired if it All Season Tires — If Equipped meets the following criteria: All Season tires provide traction for all seasons (spring, • The tire has not been driven on when flat. summer, fall and winter).
Page 280 278 STARTING AND OPERATING driving conditions. Install winter tires on your vehicle Snow Tires when ambient temperatures are less than 40°F (5°C) or if Some areas of the country require the use of snow tires roads are covered with ice or snow. For more informa- during the winter.
Page 281: Run Flat Tires - If Equipped
STARTING AND OPERATING 279 While studded tires improve performance on ice, skid It is not recommended driving a vehicle loaded at full and traction capability on wet or dry surfaces may be capacity or to tow a trailer while a tire is in the run flat poorer than that of non-studded tires.
Page 282 280 STARTING AND OPERATING Spare Tire Matching Original Equipped Tire And T, S = Temporary Spare Tire Wheel — If Equipped Since this tire has limited tread life, the original equip- Your vehicle may be equipped with a spare tire and ment tire should be repaired (or replaced) and reinstalled wheel equivalent in look and function to the original on your vehicle at the first opportunity.
Page 283 STARTING AND OPERATING 281 Limited-Use Spare — If Equipped WARNING! (Continued) The limited-use spare tire is for temporary emergency replaced. Be sure to follow the warnings, which use only. This tire is identified by a label located on the apply to your spare. Failure to do so could result in limited-use spare wheel.
Page 284: Tire Spinning
282 STARTING AND OPERATING Tire Spinning WARNING! When stuck in mud, sand, snow, or ice conditions, do not Limited-use spares are for emergency use only. In- spin your vehicle’s wheels above 30 mph (48 km/h) or for stallation of this limited-use spare tire affects vehicle longer than 30 seconds continuously without stopping.
Page 285: Tread Wear Indicators
STARTING AND OPERATING 283 These indicators are molded into the bottom of the tread Tread Wear Indicators grooves. They will appear as bands when the tread depth Tread wear indicators are in the original equipment tires becomes a 1/16 of an inch (2 mm). When the tread is to help you in determining when your tires should be worn to the tread wear indicators, the tire should be replaced.
Page 286: Replacement Tires
284 STARTING AND OPERATING • Performance tires, tires with a speed rating of V or Replacement Tires higher, and summer tires typically have a reduced The tires on your new vehicle provide a balance of many tread life. Rotation of these tires per the vehicle main- characteristics.
Page 287 STARTING AND OPERATING 285 It is recommended to replace the two front tires or two WARNING! (Continued) rear tires as a pair. Replacing just one tire can seriously braking of your vehicle. This can cause unpredict- affect your vehicle’s handling. If you ever replace a able handling and stress to steering and suspen- wheel, make sure that the wheel’s specifications match sion components.
Page 288: Tire Chains (Traction Devices)
286 STARTING AND OPERATING CAUTION! WARNING! Using tires of different size and type (M+S, Snow) Replacing original tires with tires of a different size between front and rear axles can cause unpredictable may result in false speedometer and odometer read- handling.
Page 289: Tire Rotation Recommendations
STARTING AND OPERATING 287 TIRE ROTATION RECOMMENDATIONS CAUTION! (Continued) The tires on the front and rear of your vehicle operate at • Install device as tightly as possible and then re- different loads and perform different steering, driving, tighten after driving about ½ mile (0.8 km). and braking functions.
Page 290: Tire Pressure Monitoring System (Tpms)
288 STARTING AND OPERATING The suggested rotation method is the “rearward cross” TIRE PRESSURE MONITORING SYSTEM (TPMS) shown in the following diagram. This rotation pattern The Tire Pressure Monitor System (TPMS) will warn the does not apply to some directional tires that must not be driver of a low tire pressure based on the vehicle recom- reversed.
Page 291 STARTING AND OPERATING 289 The TPMS will warn the driver of a low tire pressure if For example, your vehicle may have a recommended the tire pressure falls below the low pressure warning cold (parked for more than three hours) tire pressure of limit for any reason, including low temperature effects, or 30 psi (207 kPa).
Page 292 290 STARTING AND OPERATING CAUTION! CAUTION! (Continued) • After inspecting or adjusting the tire pressure, • The TPMS has been optimized for the original always reinstall the valve stem cap. This will equipment tires and wheels. TPMS pressures and prevent moisture and dirt from entering the valve warnings have been established for the tire size stem, which could damage the Tire Pressure Moni- equipped on your vehicle.
Page 293: Base System
STARTING AND OPERATING 291 • Driving on a significantly under-inflated tire causes Base System the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire This is the TPMS warning indicator located in the tread life, and may affect the vehicle’s handling and instrument cluster.
Page 294 292 STARTING AND OPERATING Tire Pressure Monitoring Low Pressure Warnings the “Service Tire Pressure Monitoring System” text mes- sage will display. If the ignition key is cycled, this The Tire Pressure Monitoring Telltale Light will illumi- sequence will repeat providing the system fault still nate in the instrument cluster, an audible chime will be exists.
Page 295 STARTING AND OPERATING 293 NOTE: Your vehicle may be equipped with a compact 4. This occurs for each subsequent ignition key cycle, a spare wheel and tire assembly. chime will sound and the Tire Pressure Monitoring Telltale Light will flash on and off for 75 seconds and 1.
Page 296: Enhanced System - If Equipped
294 STARTING AND OPERATING • Various Tire Pressure Monitoring System messages, Enhanced System — If Equipped which display in the Electronic Vehicle Information When the vehicle is equipped with an enhanced TPM Center (EVIC) system, the driver can view text messages showing the actual tire pressure value by position by selecting the tire •...
Page 297 STARTING AND OPERATING 295 receives the updated tire pressures, the system will auto- matically update and the “Tire Pressure Monitoring Telltale Light” will turn off. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) in order for the TPMS to receive this information.
Page 298 296 STARTING AND OPERATING A system fault can occur due to any of the following: 1. Signal interference due to electronic devices or driving next to facilities emitting the same radio frequencies as the TPM sensors. 2. Installing aftermarket window tinting that contains materials that may block radio wave signals.
Page 299 STARTING AND OPERATING 297 shown. This indicates that the pressure values are still • After driving the vehicle for up to 20 minutes above being received from the TPM sensors but they may not be 15 mph (24 km/h), the “Tire Pressure Monitoring located in the correct vehicle position.
Page 300: General Information
298 STARTING AND OPERATING pressure value instead of dashes (- -), as long as no tire The tire pressure sensors are covered under one of the pressure is below the low-pressure warning limit in any following licenses: of the four active road tires. The vehicle may need to be United States MRXC4W4MA4 driven for up to 20 minutes above 15 mph (24 km/h) in...
Page 301: Fuel Requirements - 1.4L Turbo
STARTING AND OPERATING 299 Light spark knock at low engine speeds is not harmful to Light spark knock at low engine speeds is not harmful to your engine. However, continued heavy spark knock at high your engine. However, continued heavy spark knock at high speeds can cause damage and immediate service is required.
Page 302: Gasoline/Oxygenate Blends
300 STARTING AND OPERATING Gasoline/Oxygenate Blends E-85 Usage In Non-Flex Fuel Vehicles Some fuel suppliers blend unleaded gasoline with oxy- Non-Flex Fuel Vehicles (FFV) are compatible with gaso- genates such as 10% Ethanol, Methyl Tert-Butyl Ether line containing 10% ethanol (E10). Gasoline with higher (MTBE), and Ethyl Tret-Butyl Ether (ETBE).
Page 303: Mmt In Gasoline
STARTING AND OPERATING 301 To fix a Non-FFV vehicle inadvertently fueled once with MMT. Gasoline blended with MMT reduces spark plug E-85 perform the following: life and reduces emissions system performance in some vehicles. The manufacturer recommends that gasoline • Drain the fuel tank (see your authorized dealer). without MMT be used in your vehicle.
Page 304: Fuel System Cautions
302 STARTING AND OPERATING Fuel System Cautions CAUTION! (Continued) • The use of fuel additives, which are now being CAUTION! sold as octane enhancers, is not recommended. Follow these guidelines to maintain your vehicle’s Most of these products contain high concentrations performance: of methanol.
Page 305: Carbon Monoxide Warnings
STARTING AND OPERATING 303 Carbon Monoxide Warnings WARNING! (Continued) • Guard against carbon monoxide with proper main- WARNING! tenance. Have the exhaust system inspected every Carbon monoxide (CO) in exhaust gases is deadly. time the vehicle is raised. Have any abnormal Follow the precautions below to prevent carbon conditions repaired promptly.
Page 306 304 STARTING AND OPERATING CAUTION! (Continued) into the fuel system. Also, a poorly fitting aftermar- ket cap can cause the “Malfunction Indicator Light (MIL)” to illuminate, due to fuel vapors escaping from the system. • To avoid fuel spillage and overfilling, do not “top off”...
Page 307: Loose Fuel Filler Cap Message
STARTING AND OPERATING 305 Loose Fuel Filler Cap Message WARNING! (Continued) After fuel has been added, the vehicle diagnostic system • A fire may result if gasoline is pumped into a can determine if the fuel filler cap is possibly loose, portable container that is inside of a vehicle.
Page 308: Recreational Towing (Behind Motorhome, Etc.)
306 STARTING AND OPERATING RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle Towing Condition Wheels OFF the Ground Manual Transmission Automatic Transmission Flat Tow NONE Transmission in NOT ALLOWED NEUTRAL Dolly Tow Front Rear NOT ALLOWED NOT ALLOWED On Trailer This vehicle may be towed on a flatbed or vehicle trailer CAUTION!
Page 309 STARTING AND OPERATING 307 CAUTION! Towing this vehicle in violation of the above require- ments can cause severe transmission damage. Dam- age from improper towing is not covered under the New Vehicle Limited Warranty. I n f o r ma t i o n P r o v i d e d b y :...
Page 310 I n f o r ma t i o n P r o v i d e d b y :...
Page 311: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS HAZARD WARNING FLASHERS ...311 JACKING AND TIRE CHANGING — IF EQUIPPED ......324 IF YOUR ENGINE OVERHEATS .
Page 312 310 WHAT TO DO IN EMERGENCIES ▫ Jump-Starting Procedure ....340 TOWING A DISABLED VEHICLE ...345 FREEING A STUCK VEHICLE .
Page 313: Hazard Warning Flashers
WHAT TO DO IN EMERGENCIES 311 HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located on the In any of the following situations, you can reduce the instrument panel below the radio. potential for overheating by taking the appropriate action. •...
Page 314: Tire Service Kit - If Equipped
312 WHAT TO DO IN EMERGENCIES CAUTION! WARNING! (Continued) you see or hear steam coming from under the hood, Driving with a hot cooling system could damage do not open the hood until the radiator has had time your vehicle. If the pointer rises to the H (red) mark, to cool.
Page 315: Tire Service Kit Storage
WHAT TO DO IN EMERGENCIES 313 Tire Service Kit Storage Tire Service Kit Components And Operation The Tire Service Kit is located under the front driver’s seat. Tire Service Kit Components 1 — Sealant Bottle 5 — Mode Select Knob 2 —...
Page 316: Tire Service Kit Usage Precautions
314 WHAT TO DO IN EMERGENCIES Using The Mode Select Knob And Hoses Using The Power Button Your Tire Service Kit is equipped with the following Push and release the Power Button (4) once to symbols to indicate the air or sealant mode. turn On the Tire Service Kit.
Page 317 WHAT TO DO IN EMERGENCIES 315 • When the Tire Service Kit sealant is in a liquid form, clean water, and a damp cloth will remove the material from the vehicle or tire and wheel components. Once the sealant dries, it can easily be peeled off and properly discarded. •...
Page 318 316 WHAT TO DO IN EMERGENCIES WARNING! WARNING! (Continued) • Keep Tire Service Kit away from open flames or • Do not attempt to seal a tire on the side of the heat source. vehicle closest to traffic. Pull far enough off the •...
Page 319: Sealing A Tire With Tire Service Kit
WHAT TO DO IN EMERGENCIES 317 on the ground. This will provide the best positioning WARNING! (Continued) of the kit when injecting the sealant into the deflated • Tire Service Kit Sealant solution contains latex. In tire and running the air pump. Move the vehicle as case of an allergic reaction or rash, consult a phy- necessary to place the valve stem in this position sician immediately.
Page 320 318 WHAT TO DO IN EMERGENCIES 4. Remove the cap from the valve stem and then screw NOTE: Sealant may leak out through the puncture in the the fitting at the end of the Sealant Hose (6) onto the tire. valve stem.
Page 321 WHAT TO DO IN EMERGENCIES 319 NOTE: If the Mode Select Knob (5) is on Air Mode and If the tire does not inflate to at least 26 psi (1.8 Bar) the pump is operating, air will dispense from the Air pressure within 15 minutes: Pump Hose (7) only, not the Sealant Hose (6).
Page 322 320 WHAT TO DO IN EMERGENCIES 3. Immediately disconnect the Sealant Hose (6) from the (D) Drive Vehicle: valve stem, reinstall the cap on the fitting at the end of Immediately after injecting sealant and inflating the tire, the hose, and place the Tire Service Kit in the vehicle drive the vehicle 5 miles (8 km) or 10 minutes to ensure storage location.
Page 323 WHAT TO DO IN EMERGENCIES 321 (E) After Driving: If the tire pressure is 19 psi (1.3 Bar) or higher: Pull over to a safe location. Refer to “Whenever You Stop 1. Press the Power Button (4) to turn on Tire Service Kit to Use Tire Service Kit”...
Page 324 322 WHAT TO DO IN EMERGENCIES 5. Remove the Speed Limit sticker from the instrument 4. Clean any remaining sealant from the Tire Service Kit panel after the tire has been repaired. housing. 6. Replace the Sealant Bottle (1) and Sealant Hose (6) 5.
Page 325: Wheel And Tire Torque Specifications
WHAT TO DO IN EMERGENCIES 323 Inspect the wheel mounting surface prior to mounting WHEEL AND TIRE TORQUE SPECIFICATIONS the tire and remove any corrosion or loose particles. Proper lug nut/bolt torque is very important to ensure that the wheel is properly mounted to the vehicle. Any time a wheel has been removed and reinstalled on the vehicle the lug nuts/bolts should be torqued using a properly calibrated torque wrench.
Page 326: Jacking And Tire Changing - If
324 WHAT TO DO IN EMERGENCIES Tighten the lug nuts/bolts in a star pattern until each WARNING! nut/bolt has been tightened twice. To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered.
Page 327: Jack Location
WHAT TO DO IN EMERGENCIES 325 Jack Location WARNING! (Continued) The jack and jack wrench tool are stowed in a bag under • Being under a jacked-up vehicle is dangerous. The the front driver’s seat. vehicle could slip off the jack and fall on you. You could be crushed.
Page 328: Spare Tire Removal
326 WHAT TO DO IN EMERGENCIES 2. Fit the wrench tool over the drive nut. Use the wrench Spare Tire Removal to rotate the nut counterclockwise until the spare is on The spare tire is stowed to the underbody below the the ground with enough slack in the cable to allow you cargo area.
Page 329 WHAT TO DO IN EMERGENCIES 327 CAUTION! The winch mechanism is designed for use with the jack wrench tool only. Use of an air wrench or other power tools is not recommended and they can damage the winch. 3. Pull the spare tire out from under the vehicle. Spare Tire I n f o r ma t i o n P r o v i d e d b y :...
Page 330: Preparations For Jacking
328 WHAT TO DO IN EMERGENCIES 4. Tilt the retainer at the end of the cable and pull it Preparations For Jacking through the center of the wheel. 1. Park the vehicle on a firm level surface, avoiding ice or slippery areas.
Page 331: Jacking Instructions
WHAT TO DO IN EMERGENCIES 329 5. Turn Off the ignition. Jacking Instructions 6. Block both the front and rear of the wheel diagonally WARNING! opposite of the jacking position. For example, if changing the right front Carefully follow these tire changing warnings to tire, block the left rear wheel.
Page 332 330 WHAT TO DO IN EMERGENCIES WARNING! (Continued) • Do not let anyone sit in the vehicle when it is on a jack. • Do not get under the vehicle when it is on a jack. If you need to get under a raised vehicle, take it to a Jack Warning Label service center where it can be raised on a lift.
Page 333 WHAT TO DO IN EMERGENCIES 331 2. Remove center cap. 3. Loosen, but do not remove, the wheel bolts by turning them to the left one turn while the wheel is still on the ground. NOTE: There are front and rear jacking locations on each side of the body (as indicated by the triangular lift point symbol on the sill molding).
Page 334 332 WHAT TO DO IN EMERGENCIES 4. Turn the jack screw to the left until the jack can be placed under the jacking location. Once the jack is positioned, turn the jack screw to the right until the jack head is properly engaged with the lift area closest to the wheel to be changed.
Page 335 WHAT TO DO IN EMERGENCIES 333 WARNING! WARNING! Raising the vehicle higher than necessary can make To avoid the risk of forcing the vehicle off the jack, the vehicle less stable. It could slip off the jack and do not fully tighten the wheel bolts until the vehicle hurt someone near it.
Page 336 334 WHAT TO DO IN EMERGENCIES 7. Install the spare wheel and wheel bolts with the cone WARNING! shaped end of the bolts toward the wheel. Lightly tighten the bolts. To avoid the risk of forcing the A loose tire or jack thrown forward in a collision or vehicle off the jack, do not tighten the bolts fully until hard stop could endanger the occupants of the ve- the vehicle has been lowered.
Page 337: Road Tire Installation
WHAT TO DO IN EMERGENCIES 335 Road Tire Installation Vehicles Equipped With Wheel Covers 1. Mount the road tire on the axle. 2. Align the valve notch in the wheel cover with the valve stem on the wheel. Install the cover by hand. Do not use a hammer or excessive force to install the cover.
Page 338 336 WHAT TO DO IN EMERGENCIES 3. Install the four wheel bolts with the cone shaped end of Vehicles Without Wheel Covers the nut toward the wheel. Lightly tighten the wheel bolts. 1. Mount the road tire on the axle. WARNING! 2.
Page 339: Spare Tire Stowage
WHAT TO DO IN EMERGENCIES 337 4. Finish tightening the wheel bolts. Push down on the CAUTION! wrench while at the end of the handle for increased leverage. Refer to “Torque Specifications” in this sec- The winch mechanism is designed for use with the tion for correct wheel bolt torque.
Page 340: Preparations For Jump-Start
338 WHAT TO DO IN EMERGENCIES WARNING! Do not attempt jump-starting if the battery is frozen. It could rupture or explode and cause personal injury. CAUTION! Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.
Page 341 WHAT TO DO IN EMERGENCIES 339 3. Remove the protective cover over the positive (+) WARNING! battery post. To remove the cover, press the locking tab and pull upward on the cover. • Take care to avoid the radiator cooling fan when- ever the hood is raised.
Page 342: Jump-Starting Procedure
340 WHAT TO DO IN EMERGENCIES 3. Connect the negative end (-) of the jumper cable to the Jump-Starting Procedure negative (-) post of the booster battery. WARNING! 4. Connect the opposite end of the negative (-) jumper cable to a good engine ground (exposed metal part of Failure to follow this jump-starting procedure could the discharged vehicle’s engine) away from the battery result in personal injury or property damage due to...
Page 343 WHAT TO DO IN EMERGENCIES 341 5. Start the engine in the vehicle that has the booster 4. Disconnect the positive (+) end of the jumper cable battery, let the engine idle a few minutes, and then from the positive (+) post of the discharged vehicle. start the engine in the vehicle with the discharged If frequent jump-starting is required to start your vehicle, battery.
Page 344: Freeing A Stuck Vehicle
342 WHAT TO DO IN EMERGENCIES FREEING A STUCK VEHICLE CAUTION! (Continued) If your vehicle becomes stuck in mud, sand or snow, it can the risk of clutch or transmission failure during often be moved using a rocking motion. Turn the steering prolonged efforts to free a stuck vehicle.
Page 345: Shift Lever Override
WHAT TO DO IN EMERGENCIES 343 SHIFT LEVER OVERRIDE CAUTION! (Continued) If a malfunction occurs and the shift lever cannot be • Revving the engine or spinning the wheels too fast moved out of the PARK position, you can use the may lead to transmission overheating and failure.
Page 346 344 WHAT TO DO IN EMERGENCIES 4. Press and maintain firm pressure on the brake pedal. 5. Insert a small screwdriver or similar tool into the access hole, and push and hold the override release lever in. 6. Move the shift lever to the NEUTRAL position. 7.
Page 347: Towing A Disabled Vehicle
WHAT TO DO IN EMERGENCIES 345 TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service. Towing Condition Wheels OFF The AUTOMATIC MANUAL Ground TRANSMISSION TRANSMISSION Flat Tow NONE NOT ALLOWED If transmission is operable: •...
Page 348: Automatic Transmission
346 WHAT TO DO IN EMERGENCIES Proper towing or lifting equipment is required to prevent Automatic Transmission damage to your vehicle. Use only tow bars and other • Vehicle can be towed with the front wheels elevated. equipment designed for this purpose, following equipment manufacturer’s instructions.
Page 349: Manual Transmission
WHAT TO DO IN EMERGENCIES 347 CAUTION! (Continued) CAUTION! • Towing this vehicle in violation of the above re- Towing this vehicle in violation of the above require- quirements can cause severe transmission damage. ments can cause severe engine and/or transmission Damage from improper towing is not covered un- damage.
Page 350 348 WHAT TO DO IN EMERGENCIES • Turn on the interior lights, which remain on as long as In order to move your vehicle to the side of the road you the battery has power or until the ignition key is must follow the system reset procedure.
Page 351 WHAT TO DO IN EMERGENCIES 349 Customer Action Customer Will See Customer Action Customer Will See 5. Turn Right Turn Signal Right Turn Light is ON 8. Turn ignition OFF. System is now reset and Switch ON. SOLID. Left Turn Light the engine may be BLINKS.
Page 352 I n f o r ma t i o n P r o v i d e d b y :...
Page 353: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS ENGINE COMPARTMENT — 1.4L ..353 ▫ Engine Air Cleaner Filter ....362 ENGINE COMPARTMENT — 1.4L TURBO ..354 ▫...
Page 354 352 MAINTAINING YOUR VEHICLE ▫ Automatic Transmission — If Equipped ..384 ▫ Front Turn Signal, Parking And Daytime Running Lamps..... . .403 ▫...
Page 355: Engine Compartment - 1.4L
MAINTAINING YOUR VEHICLE 353 ENGINE COMPARTMENT — 1.4L 1 — Engine Coolant Reservoir 5 — Battery 2 — Engine Oil Dipstick 6 — Air Cleaner Filter 3 — Brake Fluid Reservoir 7 — Engine Oil Fill 4 — Front Distribution Unit (Fuses) 8 —...
Page 356: Engine Compartment - 1.4L Turbo
354 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 1.4L TURBO 1 — Engine Coolant Reservoir 5 — Battery 2 — Engine Oil Dipstick 6 — Engine Oil Fill 3 — Brake Fluid Reservoir 7 — Washer Fluid Reservoir 4 — Front Distribution Unit (Fuses) I n f o r ma t i o n P r o v i d e d b y :...
Page 357: Onboard Diagnostic System - Obd Ii
MAINTAINING YOUR VEHICLE 355 ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated onboard • Prolonged driving with the MIL on could cause diagnostic system called OBD II. This system monitors further damage to the emission control system. It the performance of the emissions, engine, and automatic could also affect fuel economy and driveability.
Page 358: Emissions Inspection And Maintenance Programs
356 MAINTAINING YOUR VEHICLE Your vehicle has a simple ignition actuated test, which you EMISSIONS INSPECTION AND MAINTENANCE can use prior to going to the test station. To check if your PROGRAMS vehicle’s OBD II system is ready, you must do the following: In some localities, it may be a legal requirement to pass 1.
Page 359: Replacement Parts
MAINTAINING YOUR VEHICLE 357 • The MIL will not flash at all and will remain fully REPLACEMENT PARTS illuminated until you turn OFF the ignition or start the Use of genuine parts for normal/scheduled maintenance engine. This means that your vehicle’s OBD II system and repairs is highly recommended to ensure the de- is ready and you can proceed to the I/M station.
Page 360: Maintenance Procedures
358 MAINTAINING YOUR VEHICLE NOTE: Intentional tampering with emissions control CAUTION! systems may void your warranty and could result in civil penalties being assessed against you. • Failure to properly maintain your vehicle or per- form repairs and service when necessary could WARNING! result in more costly repairs, damage to other components or negatively impact vehicle perfor-...
Page 361: Engine Oil
MAINTAINING YOUR VEHICLE 359 Engine Oil CAUTION! Checking Oil Level Do not overfill the engine with oil. Overfilling the To assure proper engine lubrication, the engine oil must engine with oil will cause oil aeration, which can be maintained at the correct level. Check the oil level at lead to loss of oil pressure and an increase in oil regular intervals, such as every fuel stop.
Page 362 360 MAINTAINING YOUR VEHICLE Engine Oil Selection — 1.4L Engine American Petroleum Institute (API) Engine Oil Identification Symbol For best performance and maximum protection under all types of operating conditions, the manufacturer only recommends engine oils that are API Certified and meet This symbol means that the oil has the requirements of Chrysler Material Standard MS-6395.
Page 363 MAINTAINING YOUR VEHICLE 361 Engine Oil Viscosity — 1.4L Engine (SAE Grade) Engine Oil Viscosity — 1.4L Turbo Engine (SAE Grade) SAE 5W-30 engine oil recommended for all operating temperatures. This engine oil improves low temperature SAE 5W-40 full synthetic engine oil is recommended for starting and vehicle fuel economy.
Page 364: Engine Oil Filter
362 MAINTAINING YOUR VEHICLE Synthetic Engine Oils Engine Oil Filter You may use synthetic engine oils provided the recom- The engine oil filter should be replaced with a new filter mended oil quality requirements are met, and the recom- at every engine oil change. mended maintenance intervals for oil and filter changes Engine Oil Filter Selection are followed.
Page 365: Maintenance-Free Battery
MAINTAINING YOUR VEHICLE 363 Maintenance-Free Battery WARNING! Your vehicle is equipped with a maintenance-free battery. The air induction system (air cleaner, hoses, etc.) can You will never have to add water, nor is periodic main- provide a measure of protection in the case of engine tenance required.
Page 366 364 MAINTAINING YOUR VEHICLE WARNING! (Continued) CAUTION! • Battery gas is flammable and explosive. Keep • It is essential when replacing the cables on the flame or sparks away from the battery. Do not use battery that the positive cable is attached to the a booster battery or any other booster source with positive post and the negative cable is attached to an output greater than 12 Volts.
Page 367: Air Conditioner Maintenance
MAINTAINING YOUR VEHICLE 365 Air Conditioner Maintenance WARNING! (Continued) For best possible performance, your air conditioner should • The air conditioning system contains refrigerant be checked and serviced by an authorized dealer at the under high pressure. To avoid risk of personal start of each warm season.
Page 368 366 MAINTAINING YOUR VEHICLE Refrigerant Recovery And Recycling R134a — If Refrigerant Recovery And Recycling HFO 1234yf Equipped — If Equipped R-134a Air Conditioning Refrigerant is a hydrofluoro- HFO 1234yf Air Conditioning Refrigerant is a hydro- carbon (HFC) that is endorsed by the Environmental fluorocarbon (HFC) that is endorsed by the Environmen- Protection Agency and is an ozone-saving product.
Page 369 MAINTAINING YOUR VEHICLE 367 The A/C air filter is located in the fresh air inlet on the 2. Pull the console closeout cover rearward to disengage lower right of center console. Perform the following the front retaining tab and remove the cover. procedure to replace the filter: 1.
Page 370 368 MAINTAINING YOUR VEHICLE 3. Remove the two 5.5 mm screws (1 and 2) that secure the particulate air filter cover to the HVAC housing. A/C Air Filter 5. Install the A/C air filter with the air filter position indicators pointing in the same direction as removal. Air Filter Cover Screw Locations 4.
Page 371: Body Lubrication
MAINTAINING YOUR VEHICLE 369 the application of any lubricant, the parts concerned CAUTION! should be wiped clean to remove dust and grit; after lubricating excess oil and grease should be removed. The A/C air filter is identified with an arrow to Particular attention should also be given to hood latching indicate airflow direction through the filter.
Page 372 370 MAINTAINING YOUR VEHICLE Operation of the wipers on dry glass for long periods Rear Wiper Blade Removal/Installation may cause deterioration of the wiper blades. Always use 1. Lift the pivot cap on the rear wiper arm upward, this washer fluid when using the wipers to remove salt or dirt will allow the rear wiper blade to be raised off of the from a dry windshield or rear window.
Page 373 MAINTAINING YOUR VEHICLE 371 NOTE: The rear wiper arm cannot be raised fully up- ward unless the pivot cap is raised first. 2. Lift the rear wiper arm upward to raise the wiper blade off of the liftgate glass. 3. Grab the bottom of the wiper blade and rotate it forward to unsnap the blade pivot pin from the wiper blade holder.
Page 374: Adding Washer Fluid
372 MAINTAINING YOUR VEHICLE 4. Install the wiper blade pivot pin into the wiper blade Exhaust System holder at the end of the wiper arm, and firmly press The best protection against carbon monoxide entry into the wiper blade until it snaps into place. the vehicle body is a properly maintained engine exhaust 5.
Page 375 MAINTAINING YOUR VEHICLE 373 WARNING! CAUTION! • Exhaust gases can injure or kill. They contain • The catalytic converter requires the use of un- carbon monoxide (CO), which is colorless and leaded fuel only. Leaded gasoline will destroy the odorless. Breathing it can make you unconscious effectiveness of the catalyst as an emissions control and can eventually poison you.
Page 376 374 MAINTAINING YOUR VEHICLE Under normal operating conditions, the catalytic con- To minimize the possibility of catalytic converter dam- verter will not require maintenance. However, it is im- age: portant to keep the engine properly tuned to assure • Do not shut off the engine or interrupt the ignition, proper catalyst operation and prevent possible catalyst when the transmission is in gear and the vehicle is in damage.
Page 377: Cooling System
MAINTAINING YOUR VEHICLE 375 Coolant Checks Cooling System Check engine coolant (antifreeze) protection every 12 WARNING! months (before the onset of freezing weather, where applicable). If the engine coolant (antifreeze) is dirty or • When working near the radiator cooling fan, dis- rusty in appearance, the system should be drained, connect the fan motor lead or turn the ignition flushed and refilled with fresh engine coolant (anti-...
Page 378 376 MAINTAINING YOUR VEHICLE Cooling System — Drain, Flush And Refill CAUTION! NOTE: Some vehicles require special tools to add coolant • Mixing of engine coolant (antifreeze) other than properly. Failure to fill these systems properly could lead specified Organic Additive Technology (OAT) en- to severe internal engine damage.
Page 379 MAINTAINING YOUR VEHICLE 377 extended maintenance period, it is important that you use CAUTION! (Continued) the same engine coolant (OAT coolant conforming to • Do not use water alone or alcohol-based engine MS.90032) throughout the life of your vehicle. coolant (antifreeze) products. Do not use additional Please review these recommendations for using Organic rust inhibitors or antirust products, as they may not Additive Technology (OAT) engine coolant (antifreeze)
Page 380 378 MAINTAINING YOUR VEHICLE • Use only high purity water such as distilled or deion- • Mixing engine coolant (antifreeze) types is not recom- ized water when mixing the water/engine coolant mended and can result in cooling system damage. If (antifreeze) solution.
Page 381 MAINTAINING YOUR VEHICLE 379 engine coolant in open containers or allow it to remain in WARNING! puddles on the ground. If ingested by a child or pet, seek emergency assistance immediately. Clean up any ground • Do not open hot engine cooling system. Never add spills immediately.
Page 382 380 MAINTAINING YOUR VEHICLE Points To Remember • If frequent engine coolant (antifreeze) additions are required, the cooling system should be pressure tested NOTE: When the vehicle is stopped after a few miles/ for leaks. kilometers of operation, you may observe vapor coming •...
Page 383: Brake System
MAINTAINING YOUR VEHICLE 381 Be sure to clean the top of the master cylinder area before Brake System removing the cap. If necessary, add fluid to bring the In order to assure brake system performance, all brake fluid level up to the requirements described on the brake system components should be inspected periodically.
Page 384 382 MAINTAINING YOUR VEHICLE Use only manufacturer’s recommended brake fluid. Re- WARNING! (Continued) fer to “Fluids, Lubricants, and Genuine Parts” in “Main- • To avoid contamination from foreign matter or taining Your Vehicle” for further information. moisture, use only new brake fluid or fluid that has been in a tightly closed container.
Page 385: Manual Transmission - If Equipped
MAINTAINING YOUR VEHICLE 383 Manual Transmission — If Equipped WARNING! (Continued) Lubricant Selection • Do not allow petroleum-based fluid to contaminate the brake fluid. Brake seal components could be Use only the manufacturers recommended transmission damaged, causing partial or complete brake failure. fluid.
Page 386: Automatic Transmission - If Equipped
384 MAINTAINING YOUR VEHICLE Frequency Of Fluid Change CAUTION! Under normal operating conditions, the fluid installed at Using a transmission fluid other than the manufac- the factory will give satisfactory lubrication for the life of turer’s recommended fluid may cause deterioration the vehicle.
Page 387 MAINTAINING YOUR VEHICLE 385 CAUTION! CAUTION! If a transmission fluid leak occurs, visit your autho- Do not use chemical flushes in your transmission as rized dealer immediately. Severe transmission dam- the chemicals can damage your transmission compo- age may occur. Your authorized dealer has the proper nents.
Page 388: Appearance Care And Protection From Corrosion
386 MAINTAINING YOUR VEHICLE What Causes Corrosion? Appearance Care And Protection From Corrosion Corrosion is the result of deterioration or removal of Protection Of Body And Paint From Corrosion paint and protective coatings from your vehicle. Vehicle body care requirements vary according to geo- graphic locations and usage.
Page 389 MAINTAINING YOUR VEHICLE 387 • If insects, tar, or other similar deposits have accumu- Special Care lated on your vehicle, use MOPAR® Super Kleen Bug • If you drive on salted or dusty roads or if you drive and Tar Remover to remove. near the ocean, hose off the undercarriage at least once a month.
Page 390 388 MAINTAINING YOUR VEHICLE • If you carry special cargo such as chemicals, fertilizers, NOTE: If your vehicle is equipped with Dark Vapor or de-icer salt, etc., be sure that such materials are well Black Satin Chrome wheels DO NOT USE wheel cleaners, packaged and sealed.
Page 391 MAINTAINING YOUR VEHICLE 389 Stain Repel Fabric Cleaning Procedure — If Interior Care Equipped Use MOPAR® Total Clean to clean fabric upholstery and Stain Repel seats may be cleaned in the following man- carpeting. ner: Use MOPAR® Total Clean to clean vinyl upholstery. •...
Page 392 390 MAINTAINING YOUR VEHICLE To minimize the possibility of scratching the lenses and WARNING! reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution fol- Do not use volatile solvents for cleaning purposes. lowed by rinsing.
Page 393 MAINTAINING YOUR VEHICLE 391 When cleaning the rear view mirror, spray cleaner on the Cleaning Plastic Instrument Cluster Lenses towel or rag that you are using. Do not spray cleaner The lenses in front of the instruments in this vehicle are directly on the mirror.
Page 394: Convertible Top Care - If Equipped
392 MAINTAINING YOUR VEHICLE Replace the belts if they appear frayed or worn or if the Convertible Top Care — If Equipped buckles do not work properly. NOTE: Lubricate the top rails with Berulub FR 43 every 2000 cycles or if scratching noises due to dust are present. WARNING! CAUTION! A frayed or torn belt could rip apart in a collision and...
Page 395 MAINTAINING YOUR VEHICLE 393 Immediate removal of any contaminant is recommended. General Cleaning Regular washing of the top will enhance its life and Careful vacuuming of the top before washing is helpful appearance, and make successive cleanings easier. Do not in removing dust and other foreign particles.
Page 396: Fuses
394 MAINTAINING YOUR VEHICLE Scrub in all directions, covering an area of about two FUSES square feet at a time. Avoid heavy scrubbing. Rinse the entire vehicle with water to remove all soap and dirt from WARNING! the top fabric and to prevent streaking on painted and •...
Page 397: Interior Fuses
MAINTAINING YOUR VEHICLE 395 WARNING! (Continued) • If a general protection fuse for safety systems (air bag system, braking system), power unit systems (engine system, gearbox system) or steering system blows, contact an authorized dealer. Interior Fuses The interior fuse panel is part of the Body Control Module (BCM) and is located on the driver’s side under the instrument panel.
Page 398 396 MAINTAINING YOUR VEHICLE Vehicle Fuse Cavity Mini Fuse Description Number 5 Amp Tan Instrument Panel Node 20 Amp Yellow Central Door Locking 10 Amp Red Diagnostic Socket, Car Radio, Climate Control System 20 Amp Yellow Bi-Directional Washer 20 Amp Yellow Passenger Power Window 7.5 Amp Brown Left Low Beam, Headlamp Leveling...
Page 399: Underhood Fuses
MAINTAINING YOUR VEHICLE 397 The ID number of the electrical component correspond- Underhood Fuses ing to each fuse can be found on the back of the cover. The Front Distribution Unit is located on the right side of the engine compartment, next to the battery. To access the fuses, press the release tabs and remove the cover.
Page 400 398 MAINTAINING YOUR VEHICLE Cavity Maxi Fuse Mini Fuse Description 60 Amp Blue – Body Controller 20 Amp Yellow – Audio Amplifier 20 Amp Yellow – Ignition Switch 40 Amp Orange – Anti-Lock Brake Pump 70 Amp Tan – Electric Power Steering 20 Amp Yellow –...
Page 401 MAINTAINING YOUR VEHICLE 399 Cavity Maxi Fuse Mini Fuse Description – 7.5 Amp Brown Transmission – 25 Amp Clear Powertrain (Multiair – If Equipped) – 15 Amp Blue Powertrain – 15 Amp Blue Powertrain – 5 Amp Tan Powertrain (Multiair – If Equipped) –...
Page 402: Vehicle Storage
400 MAINTAINING YOUR VEHICLE Cavity Maxi Fuse Mini Fuse Description 30 Amp Green (ATO) – Rear Defroster – 5 Amp Tan Rear Defroster – 5 Amp Tan Heated Mirrors – If Equipped VEHICLE STORAGE If you are leaving your vehicle dormant for more than 21 days, you may want to take these steps to protect your battery.
Page 403: Replacement Bulbs
MAINTAINING YOUR VEHICLE 401 REPLACEMENT BULBS Interior Bulbs Bulb Number Overhead Lamp Courtesy Lamp Exterior Bulbs Bulb Number Front Low and High Beam Headlamp HIR2LL Front Parking/Daytime Running Lamps W21/5W Front Fog Lamps H11LL Front Side Marker Lamps Front Turn Signal Lamps WY21W Side Direction Lamps WY5W...
Page 404: Bulb Replacement
402 MAINTAINING YOUR VEHICLE Bulb Number Rear Tail and Stop Lamps P21/5W Rear Backup Lamps W16W Center High Mounted Stop Lamp License Plate Lamps LED (See Authorized dealer) NOTE: Numbers refer to commercial bulb types that can be purchased from your authorized dealer. If a bulb needs to be replaced, visit your authorized dealer or refer to the applicable Service Manual.
Page 405: Front Turn Signal, Parking And Daytime Running Lamps
MAINTAINING YOUR VEHICLE 403 3. Remove the plastic cap from the back of the lamp Front Turn Signal, Parking And Daytime Running housing. Lamps 1. Turn the steering wheel completely to the left or right. 4. Rotate bulb/socket counter-clockwise. 2. Open the wheel housing access door. 5.
Page 406: Rear Tail, Stop, Backup And Turn Signal Lamps
404 MAINTAINING YOUR VEHICLE 3. Pull the bulb from the socket and insert the replace- ment bulb. 4. Install the bulb and socket assembly into the housing, and rotate the socket clockwise to lock it in place. 5. Reinstall the wheel liner. Rear Tail, Stop, Backup And Turn Signal Lamps 1.
Page 407: Center High Mounted Stop Lamp (Chmsl)
MAINTAINING YOUR VEHICLE 405 4. Remove the tail, stop, or turn signal bulbs by pushing 3. Disconnect the electric connector. them slightly and turning counter-clockwise. 4. Press the retaining device and open the bulb holder. 5. Remove the backup lamp bulb by pulling straight out. 5.
Page 408: Fluid Capacities
406 MAINTAINING YOUR VEHICLE FLUID CAPACITIES U.S. Metric Fuel (Approximate) 10.5 Gallons 40 Liters Engine Oil with Filter 1.4L/1.4L Turbo Engine 4 Quarts 3.8 Liters Cooling System 1.4L/1.4L Turbo Engine (MOPAR® Antifreeze/Engine 4.6 Quarts 4.4 Liters Coolant 10 Year/150,000 Mile Formula) — with Manual Transmission 1.4L/1.4L Turbo Engine (MOPAR®...
Page 409: Fluids, Lubricants And Genuine Parts
MAINTAINING YOUR VEHICLE 407 FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant - 1.4L/1.4L Turbo We recommend you use MOPAR® Antifreeze/Coolant 10 Year/ Engine 150,000 Mile Formula OAT (Organic Additive Technology) meeting the requirements of Chrysler Material Standard MS-90032. Engine Oil - 1.4L Engine We recommend you use API Certified SAE 5W-30 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395.
Page 410 408 MAINTAINING YOUR VEHICLE Component Fluid, Lubricant, or Genuine Part Fuel Selection - 1.4L/1.4L Turbo 87 Octane Acceptable — 91 Octane Recommended Engine CAUTION! CAUTION! (Continued) OAT coolant (conforming to MS.90032), by an au- • Mixing of engine coolant (antifreeze) other than thorized dealer as soon as possible.
Page 411: Chassis
MAINTAINING YOUR VEHICLE 409 Chassis Component Fluid, Lubricant, or Genuine Part Manual Transmission – If Equipped We recommend you use MOPAR® C635 DDCT/MTX Transmission Fluid Automatic Transmission – If Use only MOPAR® AW-1 Automatic Transmission Fluid or equivalent. Equipped Failure to use the correct fluid may affect the function or performance of your transmission.
Page 412 I n f o r ma t i o n P r o v i d e d b y :...
Page 413: Maintenance Schedules
MAINTENANCE SCHEDULES CONTENTS MAINTENANCE SCHEDULE ... . .412 ▫ Maintenance Chart ....414 I n f o r ma t i o n P r o v i d e d b y :...
Page 414 412 MAINTENANCE SCHEDULES Your authorized dealer will reset the oil change indicator MAINTENANCE SCHEDULE message after completing the scheduled oil change. If a Your vehicle is equipped with an automatic oil change scheduled oil change is performed by someone other indicator system.
Page 415 MAINTENANCE SCHEDULES 413 Once A Month Or Before A Long Trip: At Every Oil Change Interval As Indicated By Oil Change Indicator System: Check engine oil level. Change oil and filter. Check windshield washer fluid level. Rotate the tires. Rotate at the first sign of irregular Check the tire inflation pressures and look for unusual wear, even if it occurs before the oil indicator wear or damage.
Page 416 414 MAINTENANCE SCHEDULES Maintenance Chart Refer to the Maintenance Schedules on the following pages for the required maintenance intervals. Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Additional Inspections Inspect the CV joints. Inspect front suspension, tie rod ends and boot seals, and replace if necessary.
Page 417 MAINTENANCE SCHEDULES 415 Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Inspect parking brake function. Adjust as necessary. Additional Maintenance Replace engine air filter. Replace cabin air filter. Clean and lube sun roof tracks. Replace spark plugs (1.4L Engine).
Page 418 416 MAINTENANCE SCHEDULES Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Flush and replace the engine coolant at 10 years or 150,000 miles (240,000 km) whichever comes first. Inspect and replace PCV valve if necessary. Replace the timing belt. ** The spark plug change interval is mileage based only, yearly intervals do not apply.
Page 419 MAINTENANCE SCHEDULES 417 WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.
Page 420 I n f o r ma t i o n P r o v i d e d b y :...
Page 421: If You Need Consumer Assistance
▫ In Canada ......425 ▫ FIAT Customer Center ....422 PUBLICATION ORDER FORMS .
Page 422 420 IF YOU NEED CONSUMER ASSISTANCE DEPARTMENT OF TRANSPORTATION UNIFORM ▫ Traction Grades ..... . .427 TIRE QUALITY GRADES ....426 ▫...
Page 423: Suggestions For Obtaining Service For Your Vehicle
IF YOU NEED CONSUMER ASSISTANCE 421 SUGGESTIONS FOR OBTAINING SERVICE FOR Be Reasonable With Requests YOUR VEHICLE If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with Prepare For The Appointment the service advisor and list the items in order of priority.
Page 424: Fiat Customer Center
P.O. Box 21–8004 Auburn Hills, MI 48321–8004 Phone: 1–800–423–6343 • If an authorized dealer is unable to resolve the con- cern, you may contact the manufacturer’s customer FIAT Canada Customer Center center. P.O. Box 1621 Windsor, Ontario N9A 4H6 Phone: 1–800–465–2001 (English) Phone: 1–800–387–9983 (French)
Page 425: Customer Assistance For The Hearing Or Speech Impaired (Tdd/Tty)
IF YOU NEED CONSUMER ASSISTANCE 423 Warranty expires. The manufacturer stands behind only Customer Assistance For The Hearing Or Speech the manufacturer’s service contracts. If you purchased a Impaired (TDD/TTY) manufacturer’s service contract, you will receive Plan To assist customers who have hearing difficulties, the Provisions and an Owner Identification Card in the mail manufacturer has installed special TDD (Telecommuni- within three weeks of the vehicle delivery date.
Page 426: Warranty Information
See the Warranty Information Booklet, located on the has also made a major investment in facilities, tools, and DVD, for the terms and provisions of FIAT Group training to assure that you are absolutely delighted with Automobiles warranties applicable to this vehicle and the ownership experience.
Page 427: In Canada
If you believe that your vehicle has a safety defect, you diagnosing/troubleshooting, problem solving, maintain- should contact the Customer Service Department imme- ing, servicing, and repairing FIAT Group Automobiles diately. Canadian customers who wish to report a safety vehicles. A complete working knowledge of the vehicle,...
Page 428 The following tire grading categories were established by assistance of service and engineering specialists to ac- the National Highway Traffic Safety Administration. The quaint you with specific FIAT Group Automobiles ve- specific grade rating assigned by the tire’s manufacturer hicles. Included are starting, operating, emergency and...
Page 429 IF YOU NEED CONSUMER ASSISTANCE 427 Treadwear Traction Grades The Treadwear grade is a comparative rating, based on the The Traction grades, from highest to lowest, are AA, A, B, wear rate of the tire when tested under controlled condi- and C.
Page 430 428 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades WARNING! The temperature grades are A (the highest), B, and C, The temperature grade for this tire is established for representing the tire’s resistance to the generation of heat a tire that is properly inflated and not overloaded. and its ability to dissipate heat, when tested under Excessive speed, under-inflation, or excessive load- controlled conditions on a specified indoor laboratory...
Page 431 INDEX I n f o r ma t i o n P r o v i d e d b y :...
Page 432 430 INDEX Adding Engine Coolant (Antifreeze) ... .377 Air Conditioner Maintenance ....365 Adding Fuel ......303 Air Conditioning.
Page 433 INDEX 431 Automatic Transmission ....233 Brakes ....... . .381 Adding Fluid .
Page 434 432 INDEX Cellular Phone ......210 Older Children And Child Restraints ..59 Chains, Tire .
Page 435 INDEX 433 Coolant Capacity ..... . .407 Dipsticks Coolant Level ......375 Automatic Transmission .
Page 436 434 INDEX New Trip ......165 Fuel Requirements ..... .298 Start Of Trip Procedure .
Page 437 INDEX 435 Engine Oil ......362 Filler Cap (Gas Cap) .....303 Engine Oil Disposal .
Page 438 436 INDEX General Information ..... . .298 Key ........11 General Maintenance.
Page 439 INDEX 437 Keys ........11 Engine Temperature Warning ....158 Key, Sentry (Immobilizer) .
Page 440 438 INDEX Locks Media Hub ......97 Automatic Door ......21 Mirrors .
Page 441 INDEX 439 Change Interval ......359 Passing Light ......109 Checking .
Page 442 440 INDEX Rear Liftgate (Sedan) ..... . .24 Safety Checks Inside Vehicle ....77 Rear Window Features .
Page 443 INDEX 441 Child Restraint ......55 Shift Lever Override ..... . .343 Extender .
Page 444 442 INDEX Steering Wheel Audio Controls ....208 Changing ......324 Steering Wheel Mounted Sound System Controls .
Page 445 INDEX 443 Tire Safety Information .....261 Trip Odometer ......156 Tire Service Kit .
Page 446 444 INDEX Washers, Windshield ..... . .113 Windows ....... .22 Washing Vehicle .
Page 447 INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this The antenna cable should be as short as practical and vehicle’s electronic system to provide immunity to radio routed away from the vehicle wiring when possible. Use frequency signals. Mobile two-way radios and telephone only fully shielded coaxial cable.
Page 448 Chrysler Group LLC 15FF500-126-AB Second Edition Rev 1 Printed in U.S.A. I n f o r ma t i o n P r o v i d e d b y :...

This manual is also suitable for:

2015 500c

Fiat 2015 500 Owner's Manual

Introduction 1

Things to Know before Starting Your Vehicle

A Word about Your Keys

Sentry Key

Remote Keyless Entry (Rke) - if Equipped

Door Locks

Power Windows

Engine Break-In Recommendations

Safety Tips

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

What to Do in Emergencies

Maintaining Your Vehicle

Quick Links

Chapters

Related Manuals for Fiat 2015 500

Summary of Contents for Fiat 2015 500