Advertisement
Quick Links
Vertriebs-
Entwicklungsgesellschaft
mbH
AMV 2125-DSP
Automatic mixing amplifier
User guide
Table of contents
1.
1.1
2.
Description of components and functions
3.
Basic operations
3.1
3.2
Use of different pre-adjustments („Presets")
3.3
3.4
Changing existing preset-adjustments
4.
4.1
Adjust new presets
4.2
Parameter-menue
4.2.1
Preset
4.2.2
4.2.3
4.2.4
Utility
4.3
Index of all programmable parameters
5.
Tecnical datas
User guide AMV 2125-DSP
page 1
Advertisement
Related Manuals for AVE AMV 2125-DSP
Summary of Contents for AVE AMV 2125-DSP
-
Page 1: Table Of Contents
Microprocessor gate control Programmable settings („Presets“) Use of different pre-adjustments („Presets“) Changing existing preset-adjustments Extended Functions Adjust new presets Parameter-menue 4.2.1 Preset 4.2.2 Parameters 4.2.3 Configuration 4.2.4 Utility Index of all programmable parameters Tecnical datas User guide AMV 2125-DSP page 1... -
Page 2: Introduction
NTERNAL MODIFICATIONS ARE TO BE COMPLETED BY AUTHORIZED PERSONNEL ONLY The AMV 2125-DSP is equipped with an approved power cable. At one end there is a three-pole mains connection socket (rubber connector) and at the other end a CE-standardized Schuko-socket to connect to a 230 V/ 50 Hz voltage source. - Page 3 Red: amplifier overdriven at input Yellow: failure – when switching on the amplifier the LED flashes short time and disappears afterwards. 11. channel switch CD/Aux: Sound carrier selection. The reproducers can be connected at the backside. User guide AMV 2125-DSP page 3...
- Page 4 Therefore Jumper 11 and 12 must be unsoldered. Mute-Switch for all or alternatively favoured inputs. By removing of one of Jumper 1 – 6 you can obtain that a favoured input is active despite of mute-switch. User guide AMV 2125-DSP page 4...
-
Page 5: Microprocessor Gate Control
3 channels 4 channels Should microphones work After removal of the corresponding independently of the automatic remove jumpers tighten the board again. the nut M3. Now you can pull the board to the rear. User guide AMV 2125-DSP page 5... -
Page 6: Programmable Settings („Presets")
Programmable settings („presets“) The AMV 2125-DSP combines numerous integrated functions with very simple operation. Even in acoustically difficult environments, best results are achieved. So-called „presets“ can easily be programmed. No less than 20 of these preset slots enable programming for any application (e.g: “Sunday”, “regular church”... -
Page 7: Extended Functions
Pushing the preset knob indicates „no“ and the display will show „Changes discarded!“ To change another preset, press briefly the “Volume”-knob. You will enter back to the preset- menu. Now change to the designated preset and proceed like described above. User guide AMV 2125-DSP page 7... - Page 8 HE FOLLOWING MODIFICATIONS ARE TO BE PERFORMED BY QUALIFIED AUDIO TECHNICIANS ONLY The Parameter-Menu / Programming of AMV 2125-DSP Functions and settings in the parameter domain should be changed by qualified personnel only. The only exception is the programming of a new preset as described in section 4.1.
-
Page 9: Parameters
„on“ or „off“. By pushing the volume dial you will return back to the parameter menu. In case you have changed any parameters, you will be asked whether you would like to save them. User guide AMV 2125-DSP page 9... -
Page 10: Configuration
By turning of the „Volume“ dial the source- and target parameterset for the copy process can be determined. When the triangle is on Copy, press the “preset” dial. Now the designated parameterset is copied. User guide AMV 2125-DSP page 10... - Page 11 Name of 2nd output Utility Copy Parameterset Copies an accumulated parameterset to another parameterset Firmware Firmware-Version EFORE OPENING THE UNIT TURN IT OFF AND REMOVE THE POWER CORD NLY THEN REMOVE THE SCREWS AND THE COVER User guide AMV 2125-DSP page 11...
-
Page 12: Technical Specifications
DSP internal accuracy: 48 bit, entire data path DSP audio clock frequency: 96 kHz, entire data path (thus, EQs are very precise at high frequencies) DSP internal overload reserve: 36dB (renders a DSP internal overload in conventional applications virtually impossible) User guide AMV 2125-DSP page 12... - Page 13 Operating voltage: 230 V~, 50-60 Hz Power consumption: 80 W/115W/130W/215W Overall dimensions: (width x height x depth) = 484 x 88 x 350 mm (+60 mm plug); 2 U, 19“ Net weight: approx. 11 kg User guide AMV 2125-DSP page 13...
- Page 14 AVE mbH Corporation. Trademarks AVE mbH and the AVE logo are trademarks or registered trademarks of AVE mbH in the Germany and other countries. Other company and product names may be trademarks of the respective companies with which they are associated.
Need help?
Do you have a question about the AMV 2125-DSP and is the answer not in the manual?
Questions and answers