Linksys SPA-3102 Setup Manual
Hide thumbs
Also See for SPA-3102:
- User manual (100 pages) ,
- Quick manual (10 pages) ,
- Product data (6 pages)
Advertisement
Quick Links
Setup Guide to the Linksys SPA3102 VoipSpeak
CLOSE X
Loading Image...
Setu p Gu ide to the Linksys SPA3102
Mar 30th, 2007 | By admin | Category: Tutorials
The Linksys SPA3102 is a cool little device that can convert your
analog phone line into a SIP trunk into your trixbox or Asterisk PBX
PBX system. The problem is most people have a ton of problems
getting them to work properly.
While there are a ton of settings, there are really only about 7
settings that need to be setup to make this work.
In this article, we will show you the idiots guide to making this cool
product work within a trixbox or FreePBX environment. We will walk you through the
FreePBX setup of the SIP trunk configuration and then show you the few settings that
you must set in order to make the SPA3102 work. Before starting, go to
http://linksys.com and get the latest firmware and update your device, then read the
article and get your SPA3102 working within just a few minutes.
Linksys SPA3102 FreePBX Configuration Setup
Go into your FreePBX interface, click on the Setup tab, then go
to the Trunk menu. From here, add a new SIP trunk. The
settings are pretty simple here but do need some explaination:
General Settings
Outbound Caller ID: "Your Company"
Within quotes, put in your caller ID name information and within
the greaterthan/lessthan brackets put in your outbound caller
id phone number. An example of this is as follows:
Outbound Caller ID: "Acme Widgets" <9495551212>
Maximum Channels: 1
You need to set the Maximum channels to 1 since the device
can only handle one concurrent call at a time.
Outgoing Settings
Trunk Name: SPA3102
PEER Details:
allow=ulaw
canreinvite=no
context=frompstn
disallow=all
host=10.10.10.50
insecure=very
nat=yes
port=5060
qualify=yes
type=peer
Unless you are using G729, you will need to allow ULAW (G711) as that is the default
Codec for the SPA3102. The host address is the IP address of the SPA3102, if this
device is outside of your local network, then set nat=yes, otherwise if it is on the local
network, use nat=no.
http://voipspeak.net/2007/03/guidetothespa3102/
Página 1 de 4
18/02/2010
Advertisement
Related Manuals for Linksys SPA-3102
Summary of Contents for Linksys SPA-3102
- Page 1 Setup Guide to the Linksys SPA3102 VoipSpeak Página 1 de 4 CLOSE X Loading Image... Setu p Gu ide to the Linksys SPA3102 Mar 30th, 2007 | By admin | Category: Tutorials The Linksys SPA3102 is a cool little device that can convert your analog phone line into a SIP trunk into your trixbox or Asterisk PBX PBX system. The problem is most people have a ton of problems getting them to work properly. While there are a ton of settings, there are really only about 7 settings that need to be setup to make this work. In this article, we will show you the idiots guide to making this cool product work within a trixbox or FreePBX environment. We will walk you through the FreePBX setup of the SIP trunk configuration and then show you the few settings that you must set in order to make the SPA3102 work. Before starting, go to http://linksys.com and get the latest firmware and update your device, then read the article and get your SPA3102 working within just a few minutes. Linksys SPA3102 FreePBX Configuration Setup Go into your FreePBX interface, click on the Setup tab, then go to the Trunk menu. From here, add a new SIP trunk. The settings are pretty simple here but do need some explaination: General Settings Outbound Caller ID: “Your Company” Within quotes, put in your caller ID name information and within the greaterthan/lessthan brackets put in your outbound caller id phone number. An example of this is as follows: Outbound Caller ID: “Acme Widgets” <9495551212> Maximum Channels: 1 You need to set the Maximum channels to 1 since the device can only handle one concurrent call at a time. Outgoing Settings Trunk Name: SPA3102 PEER Details: allow=ulaw canreinvite=no context=frompstn disallow=all ...
- Page 2 Setup Guide to the Linksys SPA3102 VoipSpeak Página 2 de 4 Incoming Settings User Context: SPA3102_In USER Details: allow=ulaw canreinvite=no context=frompstn disallow=all host=192.168.0.252 insecure=very nat=yes port=5060 type=user In the incoming settings, the host address needs to be the IP address of your Asterisk/trixbox PBX system, again use nat=yes if the SPA3102 is on another subnet or nat=no if the SPA3102 is on the same subnet as the PBX. Submit your changes and click the red apply bar, your trixbox/FreePBX system is ready to go, now you need to configure the SPA3102. SPA3102 Configuration On the rear of the SPA3102 are four ports, you should plug the phone line into the line port, an analog phone into the phone port, and connect a cable from the Ethernet port to your computer. This will assign your computer an IP address, then you can access the web interface of the SPA3102 at http://192.160.0.1. If you want the device to sit on your network and not hand out DHCP addresses, plug your regular network into the Internet port, if you have a DHCP server it will assign an IP address to the device or you can set it manually. If you are putting it as a device on your network, be sure and turn on Enable WAN Web Interface otherwise the only way to configure it is to plug a cable from the device to a computer. Here comes the fun Now, to configure it as a SIP trunk (this article does explain how to use it as an ATA) you need to click on the Voice tab, and then on the PSTN Line tab, all of the settings are going to changed here. Proxy and Registration This section tells the SPA3102 how to handle calls back and forth, since we are not using authentication, we need to disable those settings. First, set the Proxy setting to point to IP address of your PBX box, then change the settings in the section to match the list I will give you here, you should only have to adjust a few settings, but I will give you all of them to make sure you have everything setuip right: ...
- Page 3 Setup Guide to the Linksys SPA3102 VoipSpeak Página 3 de 4 Dial Plans What we are doing in this section is telling the SPA3102 how to route a call when one comes in. Basically the dialplan we use is going to say, “go to the IP address I specify and tell the system the phone number I am giving you”, this will also allow you to use the phone number you specificy as a DID for inbound route control. Dial Plan 1: (S0<: 7145551212@10.10.10.50This email address is being protected from spam bots, you need JavaScript enabled to view it :5060>) The 7145551212 is YOUR phone number, change this to be the phone number people dial to reach you. The 10.10.10.50 is the IP address of your PBX, change this to match your system configuration. VOIPToPSTN Gateway This section of the configuration tells the SPA3102 how to handle calls that come from your PBX and go out to the phone line. The factory default settings should work properly but again, I will give you the working settings just in case something isnt set right: VoIPToPSTN Gateway Enable: Yes VoIP PIN Max Retry: 3 Line 1 VoIP Caller DP:3 Line 1 Fallback DP: 1 VoIP Caller Auth Method: None One Stage Dialing: Yes VoIP Caller Default DP: 1 PSTNToVOIP Gateway This section tells the SPA3102 how to handle calls from the phone line to the PBX. While the default settings will mostly work, there are two changes you will most likely want to make, again, here is the complete list: PSTNToVoIP Gateway Enable: Yes PSTN Ring Thru Line 1: No PSTN CID For VoIP CID: Yes PSTN Caller Default DP: 1 Line 1 Signal Hook Flash To PSTN: Disabled PSTN Caller Auth Method: none PSTN PIN Max Retry: 3 PSTN CID Number Prefix: Off Hook While Calling VoIP: No PSTN CID Name Prefix: Save your settings and your SPA3102 should be ready to go! Tags: Cisco, Linksys, VoIP Gateways, VoIP Hardware, VoIP Tutorials ...
- Page 4 Setup Guide to the Linksys SPA3102 VoipSpeak Página 4 de 4 About the Author: Kerry got involved with telephony while running his own IT business. After discovering opensource systems like Asterisk, he began writing technical articles and books on the topic. With a long history in the IP PBX space from being an installer and integrator to being the project manager and Community Director for the trixbox CE project, Kerry joined the 888VoipStore team at the beginning of 2009. As the VP of Strategic Initiatives for 888VoipStore, Kerry works to help resellers to improve their businesses and bottom line by providing a rich resource of information that many have come to trust and rely upon. Need a VoIP Phone or VoIP Equipment? Get it at 888VoIPStore, the industry's leading VoIP Store. Leave Co m m ent You must be logged in to post a comment. http://voipspeak.net/2007/03/guidetothespa3102/ 18/02/2010 ...