Linksys WAG54GS User Manual page 9

Chapter4
QoS Type Select from the drop-down menu: CBR
(Continuous Bit Rate) to specify fixed bandwidth for voice
or data traffic; UBR (Unspecific Bit Rate) for application that
are not time-sensitive, such as e-mail; or VBR (Variable Bit
Rate) for bursty traffic and bandwidth-sharing with other
applications.
PCR Rate For the Peak Cell Rate (PCR), divide the DSL line
rate by 424 to get the maximum rate the sender can send
cells. Enter the rate in the field (if required by your service
provider).
SCR Rate The Sustain Cell Rate (SCR) sets the average cell
rate that can be transmitted. The SCR value is normally less
than the PCR value. Enter the rate in the field (if required
by your service provider).
Autodetect Select Enable to have the settings
automatically entered, or select Dsable to enter the
values manually.
Vrtual Crcut These fields consist of two items: VPI
(Virtual Path Identifier) and VCI (Virtual Channel Identifier).
Enter the settings provided by your ISP.
DSL Modulaton
Select
MultMode, T1.13, G.dmt, G.lte, ADSL2, or ADSL2+.
Contact your ISP if you are not sure which mode to use.
Follow the instructions for your type of encapsulation.
RFC 2364 PPPoA
Some DSL-based ISPs use PPPoA (Point-to-Point Protocol
over ATM) to establish Internet connections. If you are
connected to the Internet through a DSL line, check with
your ISP to see if they use PPPoA. If they do, you will have
to enable PPPoA.
Internet Connection Type > RFC 2364 PPPoA
PPPoA Settings
Username and Password
Password provided by your ISP.
Connect on Demand: Max Idle Tme
the Gateway to cut the Internet connection after it has
been inactive for a specified period of time (Max Idle Time).
If your Internet connection has been terminated due to
Wreless-G ADSL Gateway wth SpeedBooster
the appropriate mode:
Enter the Username and
You can configure
Advanced Configuration
inactivity, Connect on Demand enables the Gateway to
automatically re-establish your connection as soon as you
attempt to access the Internet again. To use this option,
select Connect on Demand. In the Max Idle Time field,
enter the number of minutes you want to have elapsed
before your Internet connection terminates. The default
Max Idle Time is  minutes.
Keep Alve: Redal Perod
the Gateway will periodically check your Internet
connection. If you are disconnected, then the Gateway
will automatically re-establish your connection. To use
this option, select Keep Alve. In the Redial Period field,
you specify how often you want the Gateway to check
the Internet connection. The default Redial Period is
30 seconds.
RFC 2516 PPPoE
Some DSL-based ISPs use PPPoE (Point-to-Point Protocol
over Ethernet) to establish Internet connections. If you are
connected to the Internet through a DSL line, check with
your ISP to see if they use PPPoE. If they do, you will have
to enable PPPoE.
Internet Connection Type > RFC 2516 PPPoE
PPPoE Settings
Username and Password
Password provided by your ISP.
Connect on Demand: Max Idle Tme
the Gateway to cut the Internet connection after it has
been inactive for a specified period of time (Max Idle Time).
If your Internet connection has been terminated due to
inactivity, Connect on Demand enables the Gateway to
automatically re-establish your connection as soon as you
attempt to access the Internet again. To use this option,
select Connect on Demand. In the Max Idle Time field,
enter the number of minutes you want to have elapsed
before your Internet connection terminates. The default
Max Idle Time is  minutes.
Keep Alve: Redal Perod
the Gateway will periodically check your Internet
connection. If you are disconnected, then the Gateway
If you select this option,
Enter the Username and
You can configure
If you select this option,
8