Advertisement
AUDIO IN
~
FM wire antenna
AC power cord
,------~-----------------~
-'0-
ALARM A ALARM
B
TIME ZONE
ALARMTIMEAB
aB BB
~i.~EP'
"
• "
"
=~;7g7"od ~~
:
ApMM
l_ . ... ' l_-' :l_-' l_-'
WAKE UP VOL
BB B
STEREO
~jfffOX1Wm ,',.
•
CMHz
FM 12
AM
•
JkHz
There is a tactile dot on the VOLUME
+,
~/II
and PRESETTUNING 3 button.
CR2032
About the backup
battery
To keep good time, as a backup power source, this
unit has one CR2032 battery inside of the unit in
addition to the house current.
The battery keeps the clock and the alarm operating in
the event of a power interruption.
Knowing when to replace
the battery
If a power interruption occurs when the battery is
weak, the brightness of characters in the display
darkens. If the battery runs out during the interruption,
the current time and alarm functions will be
initialized.
Replace the battery with a Sony CR2032 lithium
battery. Use of another battery may present a risk of
fire or explosion.
Replacing the backup
battery
1
Keep the AC plug connected to the AC
outlet, remove the screw that secures the
battery compartment at the bottom of the
unit using a screwdriver, and remove the
battery compartment. (See Fig.
f.i.1-G))
2
Insert a new battery in the battery
compartment with the
0
side facing up.
To remove the battery from the battery
compartment, push it out from the side marked
PUSH. (See Fig.
r..t.1-®)
3
Insert the battery compartment back into the
unit and secure it with the screw.
(See Fig.
f.i.1-®)
Note
When you replace the battery, keep the AC plug
connected to a wall outlet. Otherwise. current time
and alarms will be initialized if the replacement is not
completed within around one minute.
If the time in the display is
incorrect after the battery
is changed (RESET)
Push the Reset switch with the pointed device. The
Reset switch is in the small hole located in the battery
compartment.
Notes
• You cannot reset unless the lithium battery is
installed.
• Set the clock again after the unit is reset.
Battery Warning
When the unit will be left unplugged for a long time,
remove the battery to avoid undue battery discharge
and damage to the unit from battery leakage.
Preparing the
remote commander
Before using the card remote commander for the first
time, remove the insulation film. (See Fig.
ID-CD)
When to replace the battery
With normal use, the battery (CR2025) should last for
about six months. When the remote commander no
longer operates the unit, replace the battery with new
ones. (See Fig.
ID-®)
Notes
• Do not charge the battery.
• When you are not going to use the remote
commander for a long time, remove the battery to
avoid any damage caused by leakage and corrosion.
Note
During the shipment and your first use, a clock error
may occur. In this case, refer to "Setting the clock and
date" to set the correct time.
When daylight saving time
(summer time) begins
This model employs the Automatic Daylight. Saving
Time/Summer Time adjustment. The DST indicator in
the display appears in the display at the beginning of
the daylight saving time (summer time), and
disappears at the end of it.
• Daylight saving time begins at: 2:00 AM on the
second Sunday of March.
• Standard time begins at: 2:00 AM on the first
Sunday of November.
To deactivate the Automatic
DST/Summer Time adjustment
during the daylight saving time
(summer time) period.
The Automatic DST/Summer Time adjustment can be
cancelled.
Press CLOCK and TIME ZONE/ALARM
DISPLAY for more than two seconds. The Automatic
DST/ Summer Time adjustment will be cancelled. To
active the Automatic DST/Summer Time adjustment
again, repeat the same operation.
Setting the clock
and date
To change the setting manually, follow the procedure
from step 1.
1
Press CLOCK for more than 2 seconds.
The year will start to flash in the display.
2
Press TIME SET
+
or - until the correct
year appears in the display.
3
Press CLOCK.
4
Repeat steps
2
and 3 to set the month, day
and time.
After setting the minute the clock starts from
o
seconds. But if you do not set "Minute", the
clock does not start from 0 second flat.
• Pressing and holding
+
or - changes the year,
month, day or time rapidly.
• While setting the clock, you must perform each step
within about 65 seconds, or the clock setting mode
will be cancelled.
To display the year and date
Press CLOCK once for the date, and within
about 5 seconds press it again for the year.
The display shows the date or year for about
5 seconds and then changes back to the current time.
Setting the brightness
of the display
Three levels of brightness are available by
pressing SNOOZE/BRIGHTNESS.
Hit (default)
--->
Middle
--->
LOW]
Playing the iPod
You can enjoy iPod audio by connecting this unit. To
use an iPod, refer to the user's guide of your iPod.
Compatible iPod models
The compatible iPod models are as follows. Update
your iPod to use the latest software hefore you use it.
Setting the clock
for the first time
iPod mini
iPod nann 1st
generation
iPod 4th
generation
iPod 5th
generation (video)
iPod nano 2nd
generation
(aluminium)
iPod 4th generation
(color display)
Notes
• The connector of the unit is for sole use for iPod.
When you use the devices do not match with the
connector, connect it to the AUDIO IN terminal of
this unit with the supplied audio connecting cable.
• Sony cannot accept responsibility in the event that
data recorded to iPod is lost or damaged when using
an iPod connected to this unit.
Mountain StandardlDaylight Time
Pacific Standard/Daylight Time
Central StandardlDaylight Time
Atlantic Standard/Daylight Time
Eastern Standard/Daylight Time
Time zone
4
2
(default)
Area number
This unit is preset to the current date and time at the
factory, and is powered by the back up battery. All
you need to do the first time is just plug it in and
select your time zone.
1
Plug in the unit.
2
Press TIME ZONE for more then two
seconds.
Area number "2" appears in the display.
If you live in the Eastern Time zone, you do not
need to adjust the area setting.
CR2025
<D
888
6
Yukon Standard/Daylight Time
There is a tactile dot on the VOL
+,
~
/11,
t
and PRESET + button.
Hawaiian Standard/Daylight Time
3
Press TIME SET
+
or - repeatedly until
the desired number appears.
4
Press TIME ZONE to complete the setting.
Advertisement
