Melal Part cal return path to the chassis. Any current measured must not exceed 0.5mA. Reverse the instrument power cord plug in the out- ohmmeter let and repeat the test. See Fig. 1-1. Fig. 1-2 Insulation Resistance Test Samsung Electronics...
Page 3
(5) antenna wiring. Always inspect in all areas tinuously and new instructions are issued whenev- for pinched, out-of-place, or frayed wiring, Do not er appropriate. change spacing between a component and the printed-circuit board. Check the AC power cord for damage. Samsung Electronics...
Components i-enti- fied by shading, by( ) or by ( ) in the circuit dia- gram are important for safety or for the characteris- tics of the unit. Always replace them with the exact replacement components. Samsung Electronics...
Page 5
(6) Do not remove a replacement ESD device from its protective package until immediately before your are ready to install it.(Most replacement ESD devices are packaged with leads electrically short- ed together by conductive foam, aluminum foil or comparable conductive materials). Samsung Electronics...
Page 6
Be sure to put on a wrist strap grounded to the sheet. Be sure to lay a conductive sheet made of copper etc. Which is grounded to the table. Samsung Electronics...
Page 7
4) Insert FPC into Main PCB MCN06 and switch SW1 4) Disassemble the Deck PCB. on Deck PCB to “ON”. (See Fig 1-4) Note : If the assembly and disassembly are not done in correct sequence, the Pick-up may be damaged. TO MAIN PCB (MCN06) Fig. 1-4 Samsung Electronics...
Page 10
Reference Information Samsung Electronics...
Page 11
Reference Information 2-1-3 SIC1 (KS1452 ; Digital Servo) DIRC SSTOP /PSO SMON LOCK DFCT FOKB MIRR TZCA PHI1 XOUT TEST RSTB TILTO TILTI Samsung Electronics...
Page 12
Reference Information Samsung Electronics...
Page 13
Reference Information 2-1-4 DIC1 (KS1453 ; DVD Data Processor) Samsung Electronics...
Page 14
Reference Information Samsung Electronics...
Page 15
D a t a O u t p u t E n a b l e P o w e r ( + 5 V ) P o w e r ( + 3 . 3 V ) N . C No Connection Samsung Electronics...
Page 16
D V D - D A T A 7 / C D G - S C L K Global VREQUEST I n t e r f a c e VSTROBE A_VSS Signals ERROR A_VDD P10[10:0] V-DACK/ASTROBE AREQUEST R E S E T A-DACK ZiVA Decoder Samsung Electronics...
Page 17
Raster Contral 1 for video port. This pin receives/provides a VS/FS/FSEQ signal. RCV1 Raster Contral 2 for video port. This pin provides an HS pulse of programmable length or receives I / O RCV2 an HS pulse. 2-10 Samsung Electronics...
Page 18
The 12C-bus receiver waits for the START condition. S C L 12C serial clock input S D A I / O 12C serial data input/output TTXRQ Teletext Request output, indicating when text bits are requested T T X Teletext bit stream input Samsung Electronics 2-11...
Note : If Tray Œ doesn’t open, insert a Screw driver ¨ into the Emergency hole ˇ (as shown in detailed draw- ing) and then turn it in the direction of arrow “B”. Open Tray manually. Œ TRAY "A" ´ DOOR-TRAY "A" ¨ SCREW DRIVER ˇ EMERGENCY HOLE "B" CLOSE OPEN <Bottom View> Fig. 4-1 Door-Tray Removal Samsung Electronics...
Page 27
1) Remove 5 Screws Œ on the back Top Cabinet. 2) Remove 4 Screws ´, ˇ on the left and right side. 3) Lift up the Top Cabinet in direction of arrow. Œ 5 SCREWS ´ 2 SCREWS ˇ 2 SCREWS Fig. 4-2 Top Cabinet Removal Samsung Electronics...
Disassembly and Reaasembly 4-2 PCB Location FRONT PCB JACK PCB MAIN PCB S.M.P.S. PCB HEADPHONE PCB KEY PCB Fig. 4-7 PCB Location Samsung Electronics...
Page 33
MAIN PCB MCN01 Ô JCN04 JACK PCB HEADPHONE PCB CON23 Ò Ú FCN01 FRONT PCB JACK PCB JCN02 Æ ı FCN04 FRONT PCB MAIN PCB MCN04 ˜ ¯ TCN03 DECK PCB MAIN PCB MCN05 Fig. 4-8 Connector Diagram Samsung Electronics...
Page 34
CAUTION ; Do not stain with grease Pick-Up Lens, Turn table, Roulette Disc, Tray Disc, Belt. ˆ STOPPER "C" ˇ GEAR LOAD "C" "B" ¨ TRAY DISC ˆ STOPPER Ø FLAT CABLE ´ SCREW DRIVER Œ EMERGENCY HOLE "A" CLOSE OPEN <Bottom View> Fig. 4-9 Tray Removal Samsung Electronics...
Page 37
Œ RUBBER PAD PROTECT CAUTION ; <Assemlby Point> Suface of adhesion. ˆ HOOK "B" SLIDER RACK ˆ HOOK "B" <DETAIL-A> ˇ SCREW DRIVER ´ EMERGENCY HOLE "A" ¨ GEAR LOAD CLOSE OPEN <Bottom View> Fig. 4-12 Ass’y P/U Deck Removal 4-12 Samsung Electronics...
Page 38
1) Remove the Slider Rack ´ in direction of arrow “B”, while simultaneously pushing the Lever Locker Œ in direction of arrow “A”. <Assembly Point> "B" ´ SLIDER RACK ´ SLIDER RACK Œ LEVER LOCKER "A" Œ LEVER LOCKER Fig. 4-13 Slider Rack Removal Samsung Electronics 4-13...
Page 39
CAUTION ; Do not stain with grease Pick-Up Lens, Turn table, Roulette Disc, Tray Disc, Belt. Œ BELT PULLEY ¨ GEAR PULLEY ´ BOSS ˇ HOOK ´ BOSS ¨ GEAR PULLEY Fig. 4-14 Belt Pulley, Gear Pulley Removal 4-14 Samsung Electronics...
Page 40
3) Push the Hook ´ below the Gear Cam ¨ in the direction of arrow and lift up Gear Cam ¨. 4) Remove Gear Load ˆ. ¨ GEAR CAM ˆ GEAR LOAD ˇ GEAR CONVERT Œ GEAR TRAY ´ HOOK <Bottom Side> Fig. 4-15 Gear Tray, Gear Convert, Gear Cam, Gear Load Removal Samsung Electronics 4-15...
Page 41
3) Remove the Gear Syncro ¨ in direction of arrow “B”, while simultaneously pushing the 2 Hooks ˇ. ¨ GEAR SYNCRO ´ LEVER LOCKER "A" Œ SPRING LOCKER "B" ˇ HOOKS Fig. 4-16 Spring Locker, Lever Locker Removal 4-16 Samsung Electronics...
Page 42
2) Push the 3 Hooks ¨, ˆ, Ø in the direction of arrow “C” and lift up PCB Switch Ass’y ∏. ˇ PCB MOTOR ASS'Y ´ 2 HOOKS "B" ∏ PCB SWITCH "B" ´ 2 HOOKS Œ HOOK "A" ¨ HOOK "C" ˆ HOOK Ø HOOK "C" "C" Fig. 4-17 PCB Motor Ass’y, PCB Switch Removal Samsung Electronics 4-17...
Page 43
1) Pull the Clamper ´ by hand in the direction of arrow ”B”, while simultaneously pushing the 4 Hooks Œ in direction of arrow “A”. 2) Remove the Magnet ˇ. 3) Lift up the Plate Chuck ¨. ¨ PLATE CHUCK "B" "A" "A" ˇ MAGNET Œ 4 HOOKS ´ CLAMPER "A" "A" Fig. 4-18 Clamper Removal 4-18 Samsung Electronics...
Page 44
CAUTION ; Do not stain with grease Pick-Up Lens, Turn table, Roulette Disc, Tray Disc, Belt. Œ WASHER ´ GEAR FEED U Ø PICK-UP ASS'Y ˇ FPC ˆ SHAFT P/U "B" "C" ˆ SHAFT P/U "A" ¨ STOPPER Fig. 4-19 Pick-Up Ass’y Removal Samsung Electronics 4-19...
Page 46
Disassembly and Reaasembly 4-4-13 Spindle Motor Removal 1) Remove 3 Screws Œ. 2) Lift up the Spindle Motor ´. ´ SPINDLE MOTOR Œ 3 SCREWS Fig. 4-21 Spindle Motor Removal Samsung Electronics 4-21...
Input : Common power to transformer (Vp). Fig. 5-2 The output Vs of transformer is determined by the ratio of 1st Np and 2nd Ns. Vs = (Ns/Np) x Vp Fig. 5-3 Vout Vout is output (DC) by diode and condensor. Fig. 5-4 Samsung Electronics...
Page 51
I switch Fig. 5-6 Terms 1) 1st : Common power input to 1st winding. 2) 2nd : Circuit followings output winding of transformer. 3) f (Frequency) : Switching frequency (T : Switching cycle) 4) Duty : (Ton/T) x 100 Samsung Electronics...
Page 52
´ Rectify to PD12 and smooth to PE6. ˇ Use the output of transformer as PIC1 Vcc : The loads are different before and after PIC1 driving. (Vcc of PIC1 decreases below OFF voltage, using only the resistance due to load increase after PIC1 driving.) Samsung Electronics...
Page 53
Reverse sequence of the above description --> Duty down --> Vout down --> Maintain 5.8V (i.e., the feedback to maintains 5.8V). Œ PR35, PR36 : Reduce 5.8V overshoot ´ PR37, PC44 : Prevent PIC3 oscillation(for phase correction) ˇ PC09 : Adjust feedback response rate Samsung Electronics...
Page 54
5-1-3 (b) PIC1 (STR-G6153T) Internal Block Diagram V c c Voltage Sync. 6.3V UVLO Ref. OSC. Drain Feedback 2.5R Source Voffset S e n s e Rsense Reset Sense Sense 7.5V Reset Thermal Protection Control IC Control IC O C P Fig. 5-10 Samsung Electronics...
Page 55
RF SUM & AGC. It controls RF SUM & AGC gain by means of Pin 89-95 and interfaces with PWM signal, (output from PWM terminal of KS1453, via low-pass filter to adjust boost gain and peak frequency. EQout terminal is connected with EQin (Pin 86). Samsung Electronics...
Page 56
Œ EQG (Pin 97) : Changes the gain of peak frequency with EQ frequency characteristic. Convert PWM signal, output from KS1453, into DC via low-pass filter. ´ EQF (Pin 98) : Changes the peak frequency with EQ frequency characteristic. Convert PWM signal, output from KS1453, into DVD via low-pass filter. Samsung Electronics...
Page 60
KS1452 OPEN/CLOSE ROULETTE & MOTOR MOTOR DRIC2 DRIC2 DRIC3 FOCUSING KA3010D KA3082 KA3010D F– MOTOR DRIVE ROULETTE MOTOR DRIVE TRACKING T– DRIC1 KA3011D “ SPINDLE FIC1 LC86P6232 FRONT MICOM OPEN/CLOSE S/W ROLUETTE SENSOR DISC SENSOR Fig. 5-17 Samsung Electronics 5-11...
Page 61
Meanwhile, DVD repeats the track jump from 1 to 4 in inner direction at normal play (because data- read speed from disc is faster than data output speed on screen). ´ For CD, VCD Receive the signal output through E, F of Pick-up, from RIC1. The tracking error signal is similar to DVD. 5-12 Samsung Electronics...
Page 62
If the existing track count is within fine seek range, tracking begins using fine seek. 4) CLV SERVO(DISC MOTOR CONTROL SERVO) Input RF signal (from Pick-up) to SIC1 pin59. Detect SYNC signal from RF in SIC1, and output PWM signal to SIC1 pin 55 for constant linear velocity. Samsung Electronics 5-13...
Page 64
It measures the timing that data processed in DIC1 at DVD playback. STROBE DACK SDATA all Fig. 6-20 • CH1 : STROBE (DIC1-69, CLOCK) • CH2 : REQ (DIC1-70, DATA REQUEST) • CH3 : DACK (DIC1-58, DATA ACKNOWLEDGE) • CH4 : SDATA (DIC1-60~67, DATA) Samsung Electronics 5-15...
Page 65
Video signal converted into analog signal is outputted via amplifier of analog part. (Main Board) (Output Board) CVBS-1 Video VIC1 CVBS-2 VIC52 data A/V Decoder Amplifier ZiVA-3 BA7660 VIC50 SAA7128 Video encoder MIC1 VIC51 Main Micom Amplifier TMP93CM41F BA7660 Fig. 5-21 Video Output Block Diagram 5-16 Samsung Electronics...
Page 66
13). Pin9, Pin12 and Pin14 of VIC51 and VIC52 are feedback pin to SAG compensation(DC characteristic compen- sation of signal). Resistance(VR3-VR14) which is inserted to input terminal is bias resistance for input offset. The signal to which gain is adjusted by amplifier is outputted from jack via 75ohm. Samsung Electronics 5-17...
Page 68
D/A CONVERTER FRONT-R FILTER VIC1 (ZiVA-3) A/V Decoder DATA2 POST AIC3 SURROUND-L FILTER AK4324 POST D/A CONVERTER SURROUND-R FILTER DATA3 POST AIC4 CENTER FILTER AK4324 POST D/A CONVERTER SUB WOOFER FILTER (OPTION) Fig. 5-24 Audio Output Block Diagram Samsung Electronics 5-19...
Page 69
The 2 channels data is converted through audio decoder 2-channel data and Data 0 and Data 1 are outputted in digital audio interface.Via IEC-958 output process, they is transmitted to digital amplifier or AC-3/MPEG/DTS amplifier built in the external digital input source with IEC-958/1937 transmission format. 5-20 Samsung Electronics...