Subscribe to Our Youtube Channel
Related Manuals for Clemas & Co 1010
Summary of Contents for Clemas & Co 1010
- Page 1 1010 RIDE ON SWEEPER OPERATOR MANUAL Clemas & Co. Unit 5 Ashchurch Business Centre, Alexandra Way, Tewkesbury, Gloucestershire, GL20 8NB. Tel: 01684 850777 Fax: 01684 850707 Email: info@clemas.co.uk Web: www.clemas.co.uk...
-
Page 2: Table Of Contents
INDEX Security warning Machine registration sheet Serial number and CE marking Technical features Foreword Utilization field Unpacking the machine Precautions Assembling the side brush Preparing the battery for operation an charging Controls Instruments dashboard Starting up Operations Cleaning the waste bin Servicing the battery Replacing the filter Replacing and regulating the centre brush... - Page 3 ATTENTION:The machine has got a presence device that allows the starting upif the operator is in the correct working position. The device stops the machine in the case that the operator gets up from Any RIGHT or LEFT CLOCKWISE or COUNTER CLOCKWISE the seat.
-
Page 4: Serial Number And Ce Marking
2.2 SERIAL NUMBER AND CE MARKING Always ensure that the machine is provided with a name plate giving the serial number and CE marking in the position shown in figure.On the contrary, advise your dealer immediately. Serial number - CE marking TECHNICAL FEATURES DATI TECNICI Tensione principale... -
Page 5: Foreword
3.1 -FOREWORD 4.2 - Precautions to be taken before attempting to put the machine at work: The purpose of this manual is to inform the operator of the basic rules, safety rules and criteria which must be observed when using, adjusting and maintaining themachine. -
Page 6: Controls
CONTROLS 5.2 - INSTRUMENTS DASHBOARD 5.1 5.1 5.1 5.1 Fig.2 Fig.3 1:Brake locking pedal 1:Advance switch Pressing it with the service brake, 2, disables the latter and engages the By operating this switch, you select the direction of the machine. parking brake. -
Page 7: Cleaning The Waste Bin
STARTING UP 6.3 - CLEANING THE WASTE BIN To empty the rear waste bin operate as follows: After checking whether the battery is charged: - Release the bin lock. 1 Make sure all parts of the machine are off (centre brush, side brush, - Pull out the rear bin by grasping it by the appropriate handles. - Page 8 - ROUNTINE MAINTENANCE - ALL ROUNTINE MAINTENANCE AND SPECIAL MAINTENANCE MUST BE CARRIED OUT BY COMPETENT PERSONNEL OR BY AN AUTHORISED SERVICE CENTRE.ALWAYS USE ORIGINAL SPARE PARTS.ALL MAINTENANCE OPERATIONS MUST BE CARRIED OUT WITH THE MACHINE OFF. C O N T R O L L I C H E C K Controllare liquido batteria Check the battery liquid...
-
Page 9: Replacing The Filter
Replacing the centre brush 7.3 - REPLACING THE FILTER Before carrying out any work on the machine, make sure that it is off and that all its functions are Every 200 hours of work, the filter must be replaced. disabled. This is done by turning the key switch 3, To do so: fig. - Page 10 7.6 - Replacing the belts 7.8 - REPLACING AND REGULATING THE FLAP LIFTING CABLE ( See Fig. 6 ) To replace the flap lifting cable: -Loosen the machine nose fixing screws and remove the nose. -Loosen the bumper fixing screws and remove the bumper. Before carrying out any work on the machine, make -Loosen the cable clamp 43 fitted to the brake.
-
Page 11: Replacing And Regulating The Centre Brush
Before carrying out any work on the 7.11 REMOVING THE REAR WHEEL GEAR machine,make sure that it is off and that all MOTOR GROUP its functions are disabled. This is done by turning the key switch 3, fig.3 OFF. 1 Remove the rear bin, the batteries, the top right side casing and the two bottom casings. - Page 12 7.11.1 REPLACING THE GEAR MOTOR 7.12 REPLACING THE SUCTION FAN MOTOR (DISASSEMBLING) Once the rear wheel gear motor group has been removed, replace the gear motor as indicated here below: - The suction fan motor is replaced following the instructions given here below: 1 Remove the two rear wheels by loosening the two middle screws.
-
Page 13: Replacing The Side Brush Motor
Before carrying out any work on the machine,make 7.13 REPLACING THE CENTRE BRUSH MOTOR sure that it is off and that all its functions aredisabled. This is done by turning the key switch 3 fig.3OFF. To replace the centre brush motor, proceed as follows: 7.15 -REPLACING THE FILTER SHAKER MOTOR VIBRATOR 1 -Loosen the screws and remove the top right casing. -
Page 14: Wiring Diagram
8.2 - WIRING DIAGRAM COMPONENTS: Batt. Batteries Right side brush motor Centre brush motor Suction fan motor Filter shaker motor Motor differential Left side brush motor I.G. Battery disabling key C.Batt Battery charger socket Int.1 Side brush micro Int.2 Accelerator micro Int.3 Centre brush micro 1.25A 250V fuse... -
Page 15: Lay-Out
8.3 LAY-OUT +M1 Side brush motor power supply positive pole LED:L1 +M2 Centre brush motor power supply positive pole LED:L2 +M3 Suction fan motor power supply positive pole LED:L3 +M4 Filter shaker motor power supply positive pole LED:L4 +M5 Motor differential power supply positive pole Side brush motor power supply negative pole Centre brush motor power supply negative pole Suction fan motor power supply negative pole...
Need help?
Do you have a question about the 1010 and is the answer not in the manual?
Questions and answers