Quickset Ii Programmer; Learn From Tv; Teach To Tv; Clone Programmer - LG RU-27FB30C Series Service Manual

LT2000 & LT2002 CLONE PROGRAMMER
MPI

QUICKSET II PROGRAMMER

The Quickset II programmer LT2000 & LT2002allows cus-
tom setup and programming information to be quickly
copied from a master TV into multiple television sets.
Once learned from the master, setup data is retained in
the LT2002 for future use and recall.
When using the LT2002 operation will be easier if the
TV is connected to a good quality signal and is display-
ing a stable picture. To operate the LT2002 use the
indicated keys on an installer's remote or user's remote,
or the front panel keys on the TV receiver.
SETUP
Begin the programming process by setting up a master
TV set using one of the installer's remotes or the MBR
remote. Follow the instructions in the operating guide
for the specific TV model. Remember to set all features
that will be customized including the channel scan list,
channel labels, and installers menu setups.
Next connect the LT2002 to the master TV set using the
cable provided with the programmer. Connect the cable
between the MPI jack on the TV and the programmer.
The TV set automatically activates the programmer.
Once connected, check the "Status Indicator" LED on
the programmer. If the indicator is green and flashing
(a double-blink "heartbeat" pattern), proceed to the
next step.
3828VD0210A
Status
Indicator
Reset
Color
green battery OK
battery low
red
Blink pattern
slow
Note: A slowly flashing green light indicates there is
a problem with communications between TV and
programmer. In this case, check for damaged
cable, poor contacts, or other connection
problems. If the status indicator is red, the
programmer batteries are low.
If communications are good, the sign-on screen will be
displayed on the TV screen as shown on the quick setup
instructions. If the intention is to set TV's or
programmer's real-time clocks, and not the clone clock
or TV clock time settings, then press a key to proceed
to main clone menu.
If a previously stored TV setup is in a particular clone
memory, it may be changed if desired by overwriting it
with a new setup. There is no need for a separated memory
clear operation. Setups stored in programmer memory
are nonvolatile and will be retained even after a battery
change.

LEARN FROM TV

Select "Learn From TV" then press ON/OFF, POWER, or
ENTER to begin learning process. Alternatively, use the
TV front panel CHANNEL UP or CHANNEL DOWN keys to
highlight choice. Press ON/OFF, POWER, or ENTER to
activate. The next screen will allow a choice of three
available memories to store this TV setup. Four differ-
ent TV setups can be stored in the LT2002.
Using the On-screen menu, choose a memory or choose
to return to the main selection menu; Now press ON/
OFF, POWER or ENTER to activate your selection. The
next screen allows one last opportunity to check the
versions of TV and clone setups.
Press ON/OFF or POWER to activate learning cycle, or
press any other key to return to the selection menu to
make another choices.
Once a process has begun, the TV screen will display
"LEARNING IN PROGRESS". Please wait for the process to
complete. When the TV screen displays "LEARNING COM-
PLETED", press any key to end the learning process and
return to the clone selection menu.

TEACH TO TV

Select "TEACH TO TV", and then press ON/OFF, POWER,
or ENTER to begin teaching process. Alternatively, use
the TV front panel CHANNEL UP or DOWN keys to high-
light the choice, and then press ON/OFF, POWER, or EN-
TER to activate. The next screen displays a choice of
the three available memories that can be copied to the
TV. Select the desired memory number, and press ON/
OFF, POWER or ENTER to begin the teaching process.
Alternatively, use the TV front panel CHANNEL UP or DOWN
keys to highlight choice. Press ON/OFF, POWER, or EN-
TER to begin.
1-5
FCN - OVERVIEW