Installers Menu; Installers Menu Adjustments; Factory Menu - LG RU-27FB30C Series Service Manual

INSTALLER'S MENU ADJUSTMENTS
Installer's menu items can be accessed by using the
optional LP702 installer's remote control. Just press and
hold MENU (about 8 seconds) until the display changes,
then press 9, 8, 7, 6, then ENTER. To exit the Installer's
Menu, press ENTER again. Any changes you make will be
stored in nonvolatile memory.
The Installer's menu opens with item 0-I, INST. SEQ. Use
the SELECT key to sequence through the available menu
items. To change a setting use the Left/Right ADJ keys.
Using the Installer's Menu
Items 0-I - 95-I are accessible only in the Installer's
Menu. Their numbers, descriptions, ranges, factory de-
fault settings, and a place for listing any changes made
onsite are given below and on the following pages. The
Factory Menu that is intended for qualified service tech-
nicians only, is not shown (XX-F items). Normally Fac-
tory menu items do not require adjustment.
INSTALLERS
INSTALLER 1
INSTALLER 2
INSTALLER 3
INSTALLER 4
INSTALLER 5
INSTALLER 6
INSTALLER 7
V 1.17
Typical Installer Menu
0-I. INSTALLER SEQUENCE
Gives access to Installer Menu depending on the code
selected.
0 = 9876
2 = 1478
1-I. POWER MANAGE (Power Management)
Determines hours of no activity before automatic shutoff.
The POWER MANAGE function is for saving energy. When
set to 0, Power Manage is OFF. Settings range from 0 -
7, with 1 - 7 representing the hours that the TV will
remain on, unless there has been activity from either
the control panel or remote control.
2-I. AC ON (AC Power Switchable)
Allows the TV to turn ON just by applying AC power.
Pressing the ON button is not necessary. This is desirable
when the TV is plugged into a cable box or a power
outlet controlled by a wall switch. Use ADJ to select 0
or 1, where 0 is the default is OFF, and 1 is ON.
3828VD0210A

INSTALLERS MENU

1 = 4321
3 = 3698
NOTE: When set to 1 (ON), the TV does not respond to
ON/OFF commands from either the remote or the control
panel, and the SLEEP TIMER is also nonfunctional.
3-I. BAND/AFC (Band/Automatic Frequency Control)
There are 8 possible settings for this option:
0 = Broadcast Fixed
5 = CATV Fixed
6 = HRC Fixed
7 = ICC Fixed
Channels are accessed faster when fixed modes are used.
The AFC (search modes) should only be used when some
channels are not on nominal frequencies.
NOTE: BAND is automatically set by AUTO PROGRAM.
If some channels were not found by AUTO PROGRAM,
select the appropriate AFC setting here and add the
channels using the ADD/DEL option in the Setup Menu.
4-I. STRT CHANNEL (Start Channel)
When active, this function allows you to determine the
initial channel number when the TV is turned ON. This
feature is useful for an in-house information channel,
since the TV would always select that channel when it is
turned on. Setting this to 255 causes the last channel
viewed when TV was turned off to be the tuned to
channel when the TV is turned on again.
The range of values is 0 - 255. Use ADJ (adjust) keys to
choose numbers that determine the start channel.
5-I. CHAN LOCK (Channel Lock)
CHAN LOCK is ideal if a cable box (or similar) is the sole
source for programming—and the TV must always be on
the same channel.
Changing channels with Channel Up/Down or keypad
numbers is impossible. Channel Lock is inactive when
set to 0 (default).
Generally, this feature is used in conjunction with START
CHANNEL (item 4-I.) where the start channel may, for
example, be set to 3 or 4. If the start channel is 3, then
the TV will remain on channel 3. NOTE: When CHANNEL
LOCK is active and CHANNEL OVERIDE is disabled, AUTO
PROGRAM is not functional.
6-I. GHOST CH (Ghost Channel)
When set to 1, the current channel number is displayed
in the upper right corner of the picture. The number
moves slightly to prevent damage to the screen. The
default is "0" or OFF. NOTE: When captions are on, "Ghost
Channel" is not displayed.
2-1
4 = Broadcast AFC
1 = CATV AFC
2 = HRC AFC
3 = ICC AFC
FCN - INSTALLERS MENU