Page 1
OWNER’S MANUAL SERIAL NUMBER ______________________...
Page 2
Note: The information contained in this document is subject to change without notice. An updated version of this Owner’s Manual may be available at www.tilite.com __________________________________________________________________________________________________ SAVE THIS MANUAL FOR FUTURE REFERENCE OM0009_Rev A_AERO X_2GX Series 2 AERO X and 2GX Series 2 Owner’s Manual...
Page 3
Please take a moment to register this chair at tilite.com. This will allow us to better serve you should you have any questions regarding your TiLite. On behalf of the TiLite Team, thank you for choosing TiLite. David Lippes Founder, Chairman & CEO AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
Page 4
All information you provide to TiLite when you register will be protected by TiLite as required by applicable laws and regulations and will be used solely by TiLite. OM0009_Rev A_AERO X_2GX Series 2 AERO X and 2GX Series 2 Owner’s Manual...
FOLD HERE Quality of Service: Timeliness of Delivery: Quality of Product: 5. What additional features, if any, would you like to see on this or future TiLite products? AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
Page 6
FOLD HERE FOLD HERE TiLite Product Registration Form Please Seal with Tape Before Mailing OM0009_Rev A_AERO X_2GX Series 2 AERO X and 2GX Series 2 Owner’s Manual...
F. ARMRESTS 1-13 G. FOOTRESTS/HANGERS 1-14 H. REAR WHEELS 1-14 I. AXLES 1-14 J. PNEUMATIC TIRES 1-15 K. REAR WHEEL LOCKS 1-15 L. CASTER PIN LOCKS 1-15 AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
Page 8
ELEVATING LEGREST (ELR) Installing Adjusting the ELR Length 3-10 Adjusting the Footrest 3-10 CHAPTER 4: BACKRESTS, PUSH HANDLES AND STROLLER HANDLES ADJUSTABLE HEIGHT BACKREST Adjusting the Backrest Height OM0009_Rev A_AERO X_2GX Series 2 AERO X and 2GX Series 2 Owner’s Manual...
Page 9
TENSION ADJUSTABLE SLIDE-IN SEAT SLING Adjusting the Tension Replacing SEAT CUSHIONS Replacing the Foam Insert in the TiLite Seat Cushion VELCRO -STYLE ADJUSTABLE SEAT BELT ® Installation Adjustment viii AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
Page 10
Replacing Casters (Slipstream Single-Sided Forks) 11-4 Replacing Glide Forks (Standard and Slipstream Single-Sided) 11-4 Replacing the Elastomer 11-5 ANGLE ADJUSTABLE SPEEDLOADER CASTER MOUNT 11-6 Adjusting the Angle 11-6 OM0009_Rev A_AERO X_2GX Series 2 AERO X and 2GX Series 2 Owner’s Manual...
Page 11
12-2 CHAPTER 13: ANTI-TIPS 13-1 ANTI-TIPS 13-1 Adjusting 13-1 Mounting the Anti-Tip Receiver 13-1 USER-FRIENDLY ANTI-TIPS 13-2 Engaging 13-2 Disengaging 13-2 Adjusting 13-3 Removing 13-3 Mounting 13-3 AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
I WARNING The TiLite Aero X and 2GX wheelchairs have a weight limit of 265 pounds (120 kilograms). This weight limitation applies to the combined weight of the user and any items carried by the user. DO NOT exceed this weight limit.
If you ignore these Warnings, you may fall, tip over or lose control of the wheelchair and seriously injure yourself or others or damage the wheelchair. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
6. If you are going to tilt the chair backward, ALWAYS remind the user to lean back. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
6. Use SMALL movements of the handrims to maintain your balance on the two rear wheels. If you ignore these Warnings, you may fall, tip over or lose control of the wheelchair and seriously injure yourself or others or damage the wheelchair. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
If you ignore these Warnings, you may fall, tip over or lose control of the wheelchair and seriously injure yourself or others or damage the wheelchair. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
1. The position of the rear wheels is the most significant factor affecting your center of gravity. The more you move the rear wheels forward, the more likely your chair will tip over backward. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
4. ALWAYS move your chair as close as you can to the seat (bed, etc.) to which you are transferring. If possible, use a transfer board. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
5. NEVER reach with both hands. By keeping one hand free, you may be able to catch yourself to prevent a fall if the chair starts to tip. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
4. INSTALL ramps at entry or exit doors from your residence. Make sure the transition from such ramps to the pavement or other surface is smooth and does not have an abrupt drop-off. 5. ALWAYS make sure the floors where you live and work are level. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
9. ALWAYS lean or press your body in the UPHILL direction. This will help shift your weight to counteract the change in the center of balance caused by the hill, slope or ramp. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
Any modification or change to your chair can make it easier to tip over and you should use anti-tips until you have adapted to the modified configuration; or AERO X and 2GX Series 2 Owner’s Manual 1-11...
If you ignore these Warnings, you may fall, tip over or lose control of the wheelchair and seriously injure yourself or others or damage the wheelchair. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2 1-12...
If you ignore these Warnings, you may fall, tip over or lose control of the wheelchair and seriously injure yourself or others or damage the wheelchair. AERO X and 2GX Series 2 Owner’s Manual 1-13 OM0009_Rev A_AERO X_2GX Series 2...
If you ignore these Warnings, you may fall, tip over or lose control of the wheelchair and seriously injure yourself or others or damage the wheelchair. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2 1-14...
If you ignore these Warnings, you may fall, tip over or lose control of the wheelchair and seriously injure yourself or others or damage the wheelchair. AERO X and 2GX Series 2 Owner’s Manual 1-15 OM0009_Rev A_AERO X_2GX Series 2...
If you ignore these Warnings, you may fall, tip over or lose control of the wheelchair and seriously injure yourself or others or damage the wheelchair. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2 1-16...
You MUST make sure that axle locks properly in the axle sleeve every time you remove and reinstall a rear wheel, and you should verify this at least weekly. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
Page 30
• Inspect anti-tip wheel for cracks and wear • Inspect to ensure that anti-tip receiver is securely attached √ √ Frame • Inspect for cracks √ √ AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
“Safety Inspections and Maintenance” on pages 2-1 to 2-2. 3. If you store your chair for more than three (3) months, have your chair inspected by an authorized TiLite supplier. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
Adjust the toe-in/toe-out of the √ √ rear wheels Make sure that both sides of √ the footrest are set at an equal distance from the floor AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
3. Place the end of a ruler on the floor and hold it vertically against the corner of the footrest. See Figure 3-3. Adjust the footrest to the desired height (not less than 2” of ground clearance) and tighten the Allen screws in the clamp so the footrest height cannot change. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
Adjusting the Angle Tools Needed: • 3/16” Allen Wrench • 5/32” Allen Wrench If your flip-up footrest is angle adjustable, you can adjust the angle as follows: AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
Note: Dependent upon the seat to footrest measurement, your swing away high mount footrest may be assembled with the extension tube positioned inside the hanger. See Figure 3-2. If so, follow the procedures under “Adjusting the Height/ Replacing” on pages 3-1 and 3-2. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
“Flip-Up Footrest; Angle Adjustable Flip-Up Footrests; Depth Adjustable Flip-Up Footrests; and Depth and Angle Adjustable Flip-Up Footrests” on pages 3-1 to 3-3. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
2. Reposition the angle adjustable bracket to the desired height, lining up the holes in the angle adjustable bracket with the holes in the hanger. 3. Reinsert the Allen screw through the various washers, the angle adjustable bracket, the hanger and the locknut. Securely tighten. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
1. Align the frame plug with the frame hole. 2. Holding the hanger, not the release lever, swing the hanger until the pivot bushing locks into place in the pivot receiver. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
Receiver 1-Piece, Over-Center Folding Footrest Note: The 1-Piece, Over-Center Folding Footrest is not available on 2GX or Aero X chairs with swing away hangers. Adjusting the Height/Replacing You can adjust the height of, or replace, the footrest by using the tools and following the procedures for adjusting the height of, or replacing, a flip up footrest as set forth under “Flip-Up Footrest;...
Note: When adjusting the angle it is advisable to do so with the footrest in the flip down position so that the latch does not rotate. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
Note: To remove the ELR from the wheelchair, push the release lever, swing the ELR outward and remove the top pivot from the frame hole, lifting the ELR. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
Clamp Slot Footrest Extension Adjusting the Footrest To adjust the position of the Depth Adjustable footrest on the ELR, see “Adjusting the Depth” on page 3-3. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2 3-10...
1. Lift up and pull the back canes toward the rear of the chair. See Figure 4-3. 2. Make sure that the backrest latch on each side of the chair engages in the locked upright position. See Figure 4-2. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
2. Raise or lower the push handle to the desired height. 3. Securely tighten the adjustable handle by turning it clockwise to it’s original position. Adjustable Handle AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
CHAPTER 4: BACKRESTS, PUSH HANDLES AND STROLLER HANDLES Fold Down Push Handles To adjust the height of the Fold Down Push Handle please follow the procedures under “Adjusting the Backrest Height” on page 4-1. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
(in 3/4” increments). Washer 4. Securely tighten the Allen screw in the new location. 5. Reinstall the armrest in the armrest receiver. Armrest Allen Screw Armrest Saddle Receiver AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
5/32” Allen Wrench • 7/16” Open End Wrench Note: Unless you ordered anti-tips for your Aero X chair, the receiver may be raised or lowered to achieve a higher or lower height for the swing away armrest. 1. Remove the armrest from the receiver.
VC-3 after every fourth adjustment. If you ignore ® this Warning, you may fall, tip over or lose control of the wheelchair and seriously injure yourself or others or damage the wheelchair. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
(in 1/2” increments). Allen Armrest Screw 4. Securely tighten the Allen screw in the new location. Saddle Washer 5. Reinstall the armrest in the armrest receiver. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
Figure 6-2 Rigid Side Guards Quad Bracket Removable Side Guard Rigid Removable Side Guard Side Guard Mount Allen Clamp Screws AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
Guards, you will need to also order the Tension Adjustable by Strap Back Upholstery. To install the new back upholstery, if needed, see “Tension Adjustable by Strap Back Upholstery” on page 7-1 to 7-2. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
Page 55
Aluminum Fendered Side Guard Back Cane Band Clamp Band Clamp (threaded) (non-threaded) Washer Allen Screw #1 Seat Frame Side Guard Band Clamp Allen Screw #2 (non-threaded) Washer AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
Lift the back flap to expose the backrest ears. See Figure 7-2. 2. Completely detach the padded back from the backrest ears. Do not remove the backrest ears from the back canes. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
4. Align the top of the padded back with the two backrest ears to ensure that the top of the back upholstery is even with the top of the backrest. 5. If desired, adjust the tension of the strap(s). AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
If you ignore this Warning, you may develop pressure sores, which can be a life-threatening medical complication. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
3. Insert the flathead screwdriver into the notch on the underside of each seat tube cap and pry off both front caps. See Figure 7-4. 4. Fold the chair. 5. Remove the Slide-In Seat Sling and seat sling rods. See Figure 7-4. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
Failure to do so may result in serious injury, such as pressure ulcers. If you ignore any of these Warnings, you may incur serious or life-threatening injuries. Installation Install the seat belt as shown in Figure 7-8. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
TiLite. Quick-Release Solid Seat Pan ( Aluminum TiLite requires that your Quick-Release Solid Seat Pan be installed only by an authorized TiLite dealer. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
Page 63
Figure 8-1. Figure 8-1 Adjusting the Center of Gravity AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
1. Remove the rear wheels. 2. Remove the two hex bolts (two on each side of the chair) that secure the camber clamp to the axle plate. See Figure 8-3. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
If you ignore this Warning, you may fall, tip over or lose control of the wheelchair and seriously injure yourself or others or damage the wheelchair. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
Page 66
10. Adjust the wheel locks as needed. Figure 8-6 Figure 8-5 Measuring the Rear Wheel Spacing Adjusting the Rear Wheel Spacing Camber Clamp Camber Plug Flats Allen Screws AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
17. After adjusting the camber plugs in Step 15, it will be necessary to recheck the toe-in/toe-out. See Steps 6 through 10 above. 18. Securely tighten the Allen screws in the camber clamps. See Figure 8-5. 19. Adjust wheel locks as needed. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
Page 68
CHAPTER 8: AXLE PLATES & CAMBER PLUGS (CENTER OF GRAVITY; REAR SEAT HEIGHT) Figure 8-7 Adjusting Toe-In/Toe-Out Measurement A Figure 8-8 Figure 8-9 Adjusting Toe-In/Toe-Out Adjusting Toe-In/Toe-Out Toe-In/Toe-Out Measurement AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
If the release handle does not flip back and forth from locked to unlocked properly, or if you cannot fully engage it in the locked position or the unlocked position, the procedure below will permit you to adjust the operation of the handle. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
Page 70
Quick-Release Nut (locked position) (locked position) Quick-Release Nut Set Screw 2 Set Screw 2 Quick-Release Handle Quick-Release Handle (unlocked position) (unlocked position) Set Screw 3 Set Screw 3 AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
If you ignore this Warning, your rear wheel could become loose or fall off and you could fall, tip over or lose control of the wheelchair and seriously injure yourself or others or damage the wheelchair. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
You can adjust the rear seat height and center of gravity, and you can replace the camber plugs by following the procedures and using the tools in Chapter 8: Axle Plates and Camber Plugs (Center of Gravity; Rear Seat Height). Figure 9-5 Amputee Adapter AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
3. Slide the new wheel lock into the wheel lock clamp, but do not tighten the Allen screws. 4. Follow the procedures under “Compact Push to Lock - Adjusting” on page 10-1 to position and secure the new wheel lock. AERO X and 2GX Series 2 Owner’s Manual 10-1 OM0009_Rev A_AERO X_2GX Series 2...
2. Adjust the position of the wheel lock clamp on the frame so the wheel stop embeds at least 3/16” into the tire when engaged in the locked position. 3. Securely tighten the two Allen screws that secure the wheel lock clamp to the frame. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2 10-2...
1. Remove the Socket Head Cap screw and reposition it to either the “Pull to Lock” or ”Push to Lock” position, as desired. See Figure 10-6. 2. Securely tighten the Socket Head Cap screw. AERO X and 2GX Series 2 Owner’s Manual 10-3 OM0009_Rev A_AERO X_2GX Series 2...
1. As shown in Figure 10-11, the wheel lock handle attaches to the wheel lock handle base with two Allen screws. There is only one hole in the wheel lock handle base through which to attach the upper Allen screw. There are three holes in AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
2. Adjust the position of the wheel lock clamp on the frame so the wheel stop embeds at least 3/16” into the tire when engaged in the locked position. 3. Securely tighten the two Allen screws that secure the wheel lock clamp to the frame. AERO X and 2GX Series 2 Owner’s Manual 10-5 OM0009_Rev A_AERO X_2GX Series 2...
3. Slide the new wheel lock into the wheel lock clamp, but do not tighten the two Allen screws. 4. Follow the procedures under “Compact Scissor Lock - Adjusting” on page 10-5 to position and secure the new wheel lock. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2 10-6...
The fork stem is permanently installed in the Caster Mount. Do not attempt to unscrew the fork stem. If you have an Aero X and it becomes necessary to replace the fork Spacer 1 stem, you will need to order the Caster Mount/fork Spacer 2 stem assembly.
Steps 3 and 4 until the caster no longer floats. If the floater continues and cannot be corrected using these steps, please contact TiLite Customer Service. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
Always mount identical size casters and forks on both sides of your chair. If you ignore this Warning, you may fall, tip over or lose control of the wheelchair and seriously injure yourself or others or damage the wheelchair. AERO X and 2GX Series 2 Owner’s Manual 11-3...
6. Reinstall the casters. See “Glide Forks - Replacing Casters (Standard Fork)” on page 11-4 or “Glide Forks - Replacing Casters (Slipstream Single-Sided Fork)” on page 11-4. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
Allen Elastomer Axle Screw Allen Phillips Screw Axle Screw Allen C Spring Washer C Spring Washer Screw Phillips Screw Caster Cap Spacer Fork Spacer Caster Caster AERO X and 2GX Series 2 Owner’s Manual 11-5 OM0009_Rev A_AERO X_2GX Series 2...
11. Recheck the forks to be certain they are still perpendicular to the level surface before riding. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
Page 85
Tab Slots Caster End Cap Mount Lock Fork Stem Washer Allen Screw Fork Pivot Shoulder Bolt Allen Washer Screw Nylock Nut Elastomer Pivot Axle Allen Screw AERO X and 2GX Series 2 Owner’s Manual 11-7 OM0009_Rev A_AERO X_2GX Series 2...
Page 86
CHAPTER 11: CASTERS, FORKS AND CASTER PIN LOCKS Figure 11-13 Figure 11-14 Standard Fork Glide Fork Fork Triangle Fork Triangle Flat Edge Flat Edge AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2 11-8...
4. Lock the lever on the quad quick-release axle. 5. Pull firmly on the wheel (without unlocking the lever) to make sure the wheel is locked securely in place. AERO X and 2GX Series 2 Owner’s Manual 12-1 OM0009_Rev A_AERO X_2GX Series 2...
If you ignore this Warning, you may fall, tip over or lose control of the wheelchair and seriously injure yourself or others or damage the wheelchair. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
Page 89
4. Using a torque wrench, tighten the axle sleeve to 230 inch-pounds. Figure 12-5 Adjusting the Rear Wheel Spacing Camber Plug Washer Lock Washer Camber Axle Tube Sleeve 1/2” Spacer 1/8” Spacer AERO X and 2GX Series 2 Owner’s Manual 12-3 OM0009_Rev A_AERO X_2GX Series 2...
ALL of these parts. 5. Reinstall the rear wheels. Allen Screws Note: The backrest extension may also be secured in place by these Allen screws. AERO X and 2GX Series 2 Owner’s Manual 13-1 OM0009_Rev A_AERO X_2GX Series 2...
To disengage the User-Friendly Anti-Tip, grip the anti-tip receiver firmly and pull it downward, away from the anti-tip mounting plate, and raise it until it re-engages in the mounting plate in the position shown in Figure 13-5. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2...
Note: Unless you ordered User-Friendly Anti-Tips when you originally ordered your TiLite 2GX or Aero X, you will need to order replacement Allen screws when ordering User-Friendly Anti-Tips.
Page 94
Mounting the Anti-Tip Allen Screws Coved Washers Mounting Plate Locknuts Anti-Tip Receiver WARNING TiLite Logo Must Face Rearward and Arrows on All Anti-Tipper Components Must Align. AERO X and 2GX Series 2 Owner’s Manual OM0009_Rev A_AERO X_2GX Series 2 13-4...
Page 97
tilite.com 800.545.2266 509.586.6117 866.586.2413 509.585.8703 2701 West Court Street, Pasco, Washington 99301...
Need help?
Do you have a question about the AERO X and is the answer not in the manual?
Questions and answers