WWW.sWan-BranD.co.uK contents Important Safeguards UK Wiring Instructions Parts and Features Fabric Setting Chart Ironing Temperature Setting Guide How to use your Steam Station Prepare the Appliance for Use Fill Water Tank Steam Ironing Dry Ironing Vertical Steam Ironing Auto Shut Off Function Handle Cord Storage Replacement of Filter...
important safeguards 1. Make sure to read all the safety precautions below and look at the illustrations before you start using the appliance. 2. Use the appliance for its intended use only. 3. The appliance is intended for household use only. 4.
WWW.sWan-BranD.co.uK 16. The iron must not left unattended while it is connected to the supply mains. 17. The appliance must be used or stored in a level and horizontal surface. 18. When placing the iron on its stand, ensure that the surface on which the stand is placed is stable.
parts and Features 1. Water tank 2. Handle 3. Soleplate 4. Temperature selection button 5. Steam button 6. Steam button lock 7. Steam release button 8. Ready indicator light 9. Control panel...
Page 7
WWW.sWan-BranD.co.uK Water tank Fabric setting display...
Fabric setting chart Temperature Synthetics Wool Cottton Linen Setting low setting medium setting high setting max setting Fabric Synthetics Rayon Rayon Wool Silk Cotton Cotton Polyester Nylon Linen Linen Acrylic Acetate Ironing Dry iron Iron while Steam iron Use a Instruction on the fabric is...
WWW.sWan-BranD.co.uK ironing temperature setting guide 1. Follow the ironing instructions on the garment label. If there is no instruction label, but you know what kind of fabric it is, please refer to the fabric setting chart described opposite. 2. The fabric setting chart is only valid for plain fabrics and not for materials to which finishes, glosses etc, have been applied.
how to use your steam station prepare the appliance for use 1. Check if the rating indicated in the rating plate corresponds to the main voltage in your home. 2. Press handle button to lay handle down. (When handle is lifted up, the unit is shut off. It will be ON when handle is laid down).
WWW.sWan-BranD.co.uK Fill Water tank If there is no water or not enough water in the tank, the filling indicator light on con- trol panel will start blinking. An alarm will sound 5 BEEPs to indicate filling is needed. 1. Press the water tank lock upwards and slide the detachable water tank outwards from the base.
steam ironing 1. Fill water tank with clean tap water refering to the filling instructions. For better performance, please immerse filter in water for several minutes before installing it into the water tank. 2. Connect the appliance to a suitable socket outlet. The power indicator light (red) “...
WWW.sWan-BranD.co.uK Note: a. For first use, it is normal that a slight vibrating sound may occur from the electrical pump inside the base unit for a few seconds when steam ironing is started. It is because there is air inside the filter. It will stop when the air inside the filter has been pumped out.
Vertical steam ironing • Follow the steam ironing process, and then hold the iron in a vertical position between 5cm and 15cm away from the hanged fabrics. • Press down steam switch, this will create vertical steam. • This feature is especially used for removing creases from hanging clothes and curtains.
WWW.sWan-BranD.co.uK handle A handle is attached to the base unit for carrying the appliance. It also serves as a power on/off switch: Lifting the handle up turns power OFF and putting the handle down turns power ON. Before use, please put the handle in the down position as follows: •...
replacement of Filter Method: 1. The filter replacemnent indicator light will blink continuosly when the filter needs to be replaced. 2. To replace; slide water tank out from base unit, take the filter out from the water tank, and then replace with a new one. 3.
WWW.sWan-BranD.co.uK anti-calc system anti-cal 1. The filter is designed to reduce the build-up of limescale which occurs during steam ironing to prolong the working life of your iron. However, please note that the filter will not completely stop the natural process of limescale build-up.
troubleshooting Problems Possible Causes Solution Iron won't heat. Incorrect connection to Re-plug the unit to mains the mains socket. socket. Handle has not been laid Lay down handle. down. Temp setting is at " " Select the required ironing position. temperature according to Fabric Setting Chart.
WWW.sWan-BranD.co.uK 2 Year guarantee This product is guaranteed for two years from the date of original purchase. If any defect arises due to faulty materials or workmanship faulty products must be returned to place of purchase. Refunds or replacement is at the discretion of the store. The following conditions apply: •...
Page 20
WWW.sWan-BranD.co.uK Distributed by Swan Products Ltd PO Box 3117 Stoke-on-Trent ST4 9GD Made in China Please note the photographs and illustrations within this manual are for illustration purposes only.