Table of Contents
Advertisement
B-4
WELDER CONTROLS
POLARITY SWITCH
Turn the Arc Polarity switch to electrode positive or
electrode negative as required for each particular
application.
CONTROL OF WELDING CURRENT
Purpose of Controls
The continuous "Current Control" is the main current
adjuster. The "Job Selector" is both a fine current
adjuster and the continuous Open Circuit Voltage
adjuster. Open Circuit Voltage (OCV) controls the arc
characteristics.
"Job Selector"
The "Job Selector" dial is divided into four colored
sections providing OCV ranges as follows:
Color
Title
White
Large Electrodes
Black
Normal Welding
Red
Overhead & Vertical
Grey
Special Applications
The "Job Selector" is usually set in the black range
because it provides a soft "Buttering " arc desired for
most welding. Some operators prefer to set the "Job
Selector" in the red range for a snappy "Digging" arc
when welding vertical up or overhead.
"Current Control"
CAUTION
Do not adjust the "Current Control" while welding
because this can damage the control.
------------------------------------------------------------------------
The "Current Control" dial is calibrated in amperes on
three separate colored dials corresponding to the
white, black and red ranges of the "Job Selector" dial.
For example: when the "Job Selector" is set on the
black range, the approximate welding current is indi-
cated on the black scale of the "Current Control" dial.
How to Set the Controls
Assume you want a normal soft arc and about 135
amps, using a 5/32" (4.0 mm) electrode:
1. Set the "Job Selector" at the center of the black
range.
2. Set the "Current Control" to read 135 amps on the
black dial.
3. Start to weld.
OPERATION
4.
5. If dialing the desired current with the "Job
REMOTE CONTROL
A receptacle and "Local/Remote" control switch on the
lower front control panel and a remote control box with
100 ft. (30.5 m) of cord for adjusting the OCV at the
welding site are standard. Putting the switch in the
OCV Range
"REMOTE" position allows fine current control at the
High OCV
remote control box while placing the switch in the
Medium OCV
"LOCAL" position allows fine current control at the
Low OCV
"Job Selector" on the machine.
Extra-Low OCV
AUXILIARY POWER CONTROLS
Note: GFCI receptacles our an option and if installed,
115 VAC Receptacle
One 20 amp, 115 VAC duplex receptacle provides
115 VAC for auxiliary power. A total of 26 amps can
be drawn from this receptacle.
230 VAC Receptacle
One 15 amp, 230 VAC duplex receptacle provides
230 VAC for auxiliary power. A total of 13 amps can
be drawn from this receptacle.
Circuit Breakers
The circuit breakers provide separate overload current
protection for each half of the 115 V duplex recepta-
cle. The circuit breakers provide overload current pro-
tection in both current carrying wires of the 230 V
duplex receptacle.
Ground Stud
Provides a connection point for connecting the
machine to earth ground. For the safest grounding
procedure refer to "Machine Grounding" in the
INSTALLATION section of this manual.
SAE-400 SEVERE DUTY
If you want a little more current, turn the "Job
Selector" up (counterclockwise) to increase cur-
rent. If you want a little less current, turn the "Job
Selector" down (clockwise) to decrease current.
Selector" moves the setting outside the black
range causing undesirable arc characteristics,
turn the "Job Selector" back to the center of the
black range. Then turn the "Current Control" up or
down a little as needed. Readjust the "Job
Selector" for the exact characteristics and current
desired.
see the "MAINTENANCE SECTION" for
detailed information on testing and resetting the
GFCI receptacle.
B-4
Advertisement
Table of Contents
Troubleshooting
