Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Siqura BC620WDR
Summary of Contents for Siqura BC620WDR
- Page 1 BC620WDR Series IP box camera with dual H.264 and WDR...
- Page 2 Any brand names mentioned in this manual are registered trademarks of their respective owners. Liability Siqura accepts no liability for claims from third parties arising from improper use other than that stated in this manual. Although considerable care has been taken to ensure a correct and suitably comprehensive description of all relevant product components, this manual may nonetheless contain errors and inaccuracies.
-
Page 3: Table Of Contents
Contents About this manual ..................Safety and compliance ................Safety ....................Cautions ..................... Compliance ..................Product overview ..................Models ....................Features ..................... Package contents ................. Dimensions ..................Back panel ....................Features and indications ............... Cable connection ..................Connect audio ..................Connect data RS-485 ................ -
Page 4: About This Manual
About this manual What this manual covers This manual describes how to install and connect the BC620WDR, Siqura's IP box camera with dual H.264 and WDR. Instructions for configuration and operation of the BC620WDR can be found in the User Manual. -
Page 5: Safety And Compliance
Failure to comply with any precaution, warning, or instruction noted in the manual is in violation of the standards of design, manufacture, and intended use of the module. Siqura assumes no liability for the customer's failure to comply with any of these safety requirements. - Page 6 Specifications of this product. Optical safety The following optical safety information applies to BC620WDR models with SFP interface. This product complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007. This optical equipment contains Class 1M lasers or LEDs and has been designed and tested to meet IEC 60825-1:1993+A1+A2 and IEC 60825-2:2004 safety class 1M requirements.
-
Page 7: Cautions
European Union (EU) to enact the Directive on the Restriction of the use of certain Hazardous Substances (RoHS) (2002/95/EC). Siqura offers products that comply with the EU’s RoHS Directive. The full version of the Siqura RoHS statement can be viewed at www.siqura.com. -
Page 8: Compliance
Safety and compliance Compliance... -
Page 9: Product Overview
BC620WDR-PID/SFP Network box camera, super WDR, PID, D1 resolution, dual H.264, SFP interface Note: The BC620WDR can be configured to either NTSC or PAL, with the default set to PAL for EMEA and APAC, and to NTSC for the US. -
Page 10: Features
Product overview Features BC620WDR Series Common features ● 1/3” Pixim DPS Seawolf Imager ● D1 resolution ● ONVIF Profile S ● Day/Night with IR-cut filter ● Wide dynamic range ● Backlight compensation ● Alarm: two inputs / two outputs ●... -
Page 11: Package Contents
Product overview Package contents BC620WDR C mount lens adapter Back focus adjuster (lens not included) 5-Pin terminal block (2x) 2-Pin terminal block Power adapter CD (Manuals and software) Quick Start Guide Dimensions... -
Page 12: Back Panel
Back panel This chapter describes the connectors and other features on the back panel of the BC620WDR. In This Chapter 4.1 Features and indications..................12 Features and indications BC620WDR back panel No. Item Description CC IN/OUT Connector for digital I/O : GND ┴... - Page 13 Network connector RJ-45 with 802.3af PoE SFP connector (on SFP model) Used for direct connection to fiber optic cabling or coax (via Siqura ECO-plug) Reset button Press and hold for 10 sec. to reset to factory defaults (incl. network settings).
-
Page 14: Cable Connection
User Manual. Connect data RS-485 The BC620WDR itself does not have PTZ functionality, but it can be mounted on a PTZ mounting bracket which can then be controlled from the data port (RS-422/485) on the back panel of the BC620WDR. -
Page 15: Connect Digital I/O
RS-485 definitions Note: For 2-wire RS-485 use pins 6 and 7. Connect digital I/O The BC620WDR is equipped with two digital inputs and two digital outputs for alarm applications. To connect alarm devices Insert the alarm wiring into the supplied 5-pin terminal block. -
Page 16: Power The Camera
Cable connection Power the camera BC620WDR series cameras support 12 Vdc and 24 Vac via terminal block, and Power over Ethernet (802.3af PoE). To power the camera via terminal block Connect the leads from a 12 Vdc or 24 Vac power supply (not included) to the supplied terminal block in accordance with the connection assignments on the back panel of the camera. -
Page 17: Use The Analogue Video Output
Yellow on/blink : link OK, active Yellow off/flash : link down, TX attempt Use the analogue video output With its analogue output, the hybrid BC620WDR solution can provide local video for a public view monitor. To connect a local monitor ●... -
Page 18: Mount The Lens And The Camera
The BC620WDR supports C-mount and CS-mount lenses. Mount a lens onto the BC620WDR To mount a lens onto the BC620WDR camera Remove the CCD cover from the camera. If you have a C-mount lens, attach the supplied C/CS mount adapter to the camera. -
Page 19: Mount The Camera
Mount the lens and the camera Mount the camera The BC620WDR can be installed directly on a wall or ceiling, provided the surface has sufficient strength to support the camera. In addition, the BC620WDR is fitted with a mounting block which can be fixed to either the top or bottom of the camera. -
Page 20: System
System This chapter gives the system requirements for PCs used to access the BC620WDR. In This Chapter 7.1 System requirements.................... 20 7.2 System compatibility..................... 20 System requirements The BC620WDR camera can be accessed and configured from a standard web browser supporting ActiveX controls. -
Page 21: Appendix: Use Focus Assist
Appendix: Use focus assist BC620WDR includes Focus Assist functionality to achieve optimal image quality. Focus Assist can be used from the Video page but also from the back of the camera body. The latter may prove useful when setting the focus without a monitor. -
Page 22: Appendix: Adjust Back Focus
Required tools ● Back focus adjuster (in the BC620WDR camera package) ● Test chart / contrasting object To adjust back focus Set the camera on a stable mount at least 75 feet (23 metres) away (or as far as possible) from the test chart or object. -
Page 23: Index
Index About this manual........4 Appendix: Adjust back focus....22 Appendix: Use focus assist.......21 Back panel..........12 Cable connection........14 Cautions..........7 Compliance..........8 Connect audio........14 Connect data RS-485......14 Connect digital I/O........15 Connect to network.........16 Dimensions..........11 Features..........10 Features and indications......12 Models............
Need help?
Do you have a question about the BC620WDR and is the answer not in the manual?
Questions and answers