Lincoln Electric POWER MIG 140 Operator's Manual
Lincoln electric welder user manual
Hide thumbs
Also See for POWER MIG 140:
- Operator's manual (39 pages) ,
- Operator's manual (52 pages) ,
- Operator's manual (128 pages)
Table of Contents
Advertisement
RETURN TO MAIN MENU
IM890-A
POWER MIG (140, 180 MODELS)
May, 2007
Safety Depends on You
Lincoln arc welding and cutting
equipment is designed and built
with safety in mind. However, your
overall safety can be increased by
proper installation ... and thought-
ful operation on your part. DO
NOT INSTALL, OPERATE OR
REPAIR THIS EQUIPMENT
WITHOUT
READING
THIS
MANUAL AND THE SAFETY
PRECAUTIONS CONTAINED
THROUGHOUT. And, most
importantly, think before you act
and be careful.
OPERATOR'S MANUAL
Copyright © 2007 Lincoln Global Inc.
Advertisement
Table of Contents
Related Manuals for Lincoln Electric POWER MIG 140
Summary of Contents for Lincoln Electric POWER MIG 140
- Page 1 RETURN TO MAIN MENU IM890-A POWER MIG (140, 180 MODELS) May, 2007 Safety Depends on You Lincoln arc welding and cutting equipment is designed and built with safety in mind. However, your overall safety can be increased by proper installation ... and thought- ful operation on your part.
- Page 6 EN 60974-10...
- Page 7 EN 60974-10:...
- Page 8 T T h h a a n n k k Y Y o o u u...
- Page 13 INNER WIRE GUIDE INNER WIRE GUIDE .025-.035 (.6-.9mm) .035-.045 (.9-1.1mm) REGULATOR 2" SPINDLE ADAPTER (FOR 8" REEL OF WIRE) GAS HOSE "LEARN TO WELD" OUTER WIRE GUIDE LTW1...
- Page 15 .035"(0.9mm) NR-211-MP WIRE SPOOL...
- Page 16 2"(51mm) SPINDLE ADAPTER (FOR 8"(20mm) REEL OF WIRE) ( 4"(102mm) REEL OF WIRE) TOP DRIVE ROLL PRESSURE ARM TENSION ADJUSTOR DOWN WIRE SPOOL .035" (0.9mm) NR-211-MP INNER WIRE GUIDE REMOVED LOWER DRIVE ROLL REMOVED OUTER WIRE GUIDE REMOVED...
- Page 18 INNER WIRE GUIDE .025-.035 (.6-.9mm)
- Page 19 LOCATE COMPONENTS TO CONNECT TO THE FRONT OF MACHINE ALL COMPONENTS SHOWN CONNECTED (FRONT AND SIDE DOOR IS REMOVED FOR CLARITY) THUMB SCREW TO TIGHTEN CONNECTOR BUSHING TOP DRIVE ROLL PRESSURE ARM TENSION ADJUSTOR DOWN WIRE SPOOL .035" (0.9mm) NR-211-MP INNER WIRE GUIDE REMOVED LOWER DRIVE ROLL REMOVED SHORT POWER...
- Page 20 TOP DRIVE ROLL PRESSED AGAINST LOWER DRIVE ROLL TENSION ADJUSTOR LOCKED IN POSITION SLIDE WIRE INTO GUN CONNECTOR SIDE LOWER DRIVE ROLL BE SURE WIRE IS IN GROOVE REMOVED NOZZLE REMOVED CONTACT TIP LAY CABLE AND GUN STRAIGHTEN IN THIS POSITION ON/OFF SWITCH FEED WIRE...
- Page 21 INNER WIRE GUIDE .025-.035 FEMALE END MALE END 75/25 100% MIXES (REQUIRES ADAPTER SOLD SEPARATELY)
- Page 22 MALE END REGULATOR ADAPTER S19298 PLASTIC WASHER 100% FEMALE END 75/25 MIXES...
- Page 23 LOCATE COMPONENTS TO CONNECT TO THE FRONT OF MACHINE ALL COMPONENTS SHOWN CONNECTED (FRONT AND SIDE DOOR IS REMOVED FOR CLARITY) THUMB SCREW TO TIGHTEN CONNECTOR BUSHING TOP DRIVE ROLL PRESSURE ARM TENSION ADJUSTOR DOWN WIRE SPOOL .025" (0.6mm) INNER WIRE GUIDE REMOVED LOWER DRIVE ROLL REMOVED WORK LEAD CONNECTION...
- Page 24 TOP IDLER ROLL PRESSED AGAINST LOWER DRIVE ROLL TENSION ADJUSTOR LOCKED IN POSITION SLIDE WIRE INTO GUN CONNECTOR SIDE DRIVE ROLL BE SURE WIRE IS IN GROOVE REMOVED NOZZLE REMOVED CONTACT TIP LAY CABLE AND GUN STRAIGHTEN IN THIS POSITION ON/OFF SWITCH FEED WIRE...
- Page 27 For mounting welding machines to K520 carts that do not have slotted mounting holes, Drill 9/32” holes (3 places) into the cart top as shown and attach the welding machine to the cart with the proper hardware shown. 1/4"-20 X 1" Thread Forming Screw (1 Required) 3-3/4"...
- Page 28 For mounting welding machines to K2275 carts that do not have slotted mounting holes, Drill 9/32” holes (3 places) into the cart top as shown and attach the welding machine to the cart with the proper hardware shown. 1/4"-20 X 1/2" Hex Head Cap Screw (2 Required) 1/4"-20 X 1"...
- Page 36 Enhanced Diagram...