Table of Contents
Advertisement
Quick Links
1.
OVERVIEW.......................................................................................................................................... 1
2.
INSTALLATION................................................................................................................................... 3
3.
SPECIFICATIONS............................................................................................................................... 4
3.1. SERIAL VIDEO INPUT ............................................................................................................... 4
3.2. SERIAL VIDEO OUTPUTS......................................................................................................... 4
3.3. ELECTRICAL ............................................................................................................................. 4
3.4. PHYSICAL .................................................................................................................................. 4
4.
STATUS LEDS .................................................................................................................................... 5
4.1. INPUT 1 INDICATORS ............................................................................................................... 5
4.2. INPUT 2 INDICATORS ............................................................................................................... 6
5.
LOCATION OF LEDS AND JUMPERS .............................................................................................. 7
BY THE GLOBAL FRAME STATUS.......................................................................................... 7
5.2. SELECTING NON-RECLOCK MODE ........................................................................................ 8
6.
®
6.2. MONITOR SETTINGS TAB...................................................................................................... 10
6.2.1. Lock Status ......................................................................................................................... 10
6.2.2. Bypass Select ..................................................................................................................... 10
6.2.3. Input Video Rate ................................................................................................................. 11
6.3. FAULT TRAPS TAB................................................................................................................. 11
6.3.1. Module OK Trap Status....................................................................................................... 11
Figures
Figure 1-1: 500DA2Q-3G Block Diagram..............................................................................................................2
Figure 2-1: 500DA2Q-3G Rear Panel Overlay......................................................................................................3
Figure 5-1: LED and Jumper Locations ................................................................................................................7
Figure 5-1: VistaLINK
Figure 5-1: VistaLINK
500DA2Q-3G 3G/HD/SD-SDI Dual Reclocking Distribution Amplifier
TABLE OF CONTENTS
? ............................................................................................................. 9
®
500DA-3G Monitor Status Tab.......................................................................................10
®
500DA-3G Fault Traps Tab............................................................................................11
®
Revision 2.0
Frame Manual
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for evertz 500DA2Q-3G
Summary of Contents for evertz 500DA2Q-3G
-
Page 1: Table Of Contents
Frame Manual 500DA2Q-3G 3G/HD/SD-SDI Dual Reclocking Distribution Amplifier TABLE OF CONTENTS OVERVIEW............................1 INSTALLATION........................... 3 SPECIFICATIONS..........................4 3.1. SERIAL VIDEO INPUT ....................... 4 3.2. SERIAL VIDEO OUTPUTS......................4 3.3. ELECTRICAL ..........................4 3.4. PHYSICAL ..........................4 STATUS LEDS ............................ 5 4.1. -
Page 2: Revision History
Information contained in this manual is believed to be accurate and reliable. However, Evertz assumes no responsibility for the use thereof nor for the rights of third parties, which may be affected in any way by the use thereof. Any representations in this document concerning performance of Evertz products are for informational use only and are not warranties of future performance, either expressed or implied. -
Page 3: Overview
The 500DA2Q-3G features two auto-equalized inputs and can be individually set via jumpers for either reclocking or non-reclocking. The 500DA2Q-3G is housed in the 500FR exponent frame that will hold up to 16 modules. Features: • Normal reclocked mode for SMPTE 424M (3Gb/s), SMPTE 292M (1.5Gb/s) and SMPTE 259M (270Mb/s) •... -
Page 4: Figure 1-1: 500Da2Q-3G Block Diagram
Frame Manual 500DA2Q-3G 3G/HD/SD-SDI Dual Reclocking Distribution Amplifier Figure 1-1: 500DA2Q-3G Block Diagram Page - 2 Revision 2.0... -
Page 5: Installation
500DA2Q-3G 3G/HD/SD-SDI Dual Reclocking Distribution Amplifier INSTALLATION The 500DA2Q-3G comes with a companion rear panel overlay that can be placed over the rear panel BNC connectors to identify their function. For information on inserting the module into the frame see section 3 of the 500FR chapter. -
Page 6: Specifications
Frame Manual 500DA2Q-3G 3G/HD/SD-SDI Dual Reclocking Distribution Amplifier SPECIFICATIONS 3.1. SERIAL VIDEO INPUT Standards: Reclocked Mode: SMPTE 424M (3Gb/s), SMPTE 292M (1.5Gbs), SMPTE 259M (270Mb/s) Non Reclocked Mode: SMPTE 344M (540Mb/s), SMPTE 259M (360Mb/s, 143Mb/s), SMPTE 310M (19.4Mb/s), DVB-ASI Connector:... -
Page 7: Status Leds
500DA2Q-3G 3G/HD/SD-SDI Dual Reclocking Distribution Amplifier STATUS LEDS The 500DA2Q-3G has twelve LED Status indicators on the front card edge to show operational status of the card at a glance. Figure 5-1 shows the location of the LEDs. Two large LEDs on the front of the board indicate the general health of the module:... -
Page 8: Input 2 Indicators
Frame Manual 500DA2Q-3G 3G/HD/SD-SDI Dual Reclocking Distribution Amplifier 4.2. INPUT 2 INDICATORS There are three small LEDs at the bottom of the module that indicate the status of equalizer for input 2 and the reclocker 2 rate. CARRIER PRESENT: This Green LED will be On when cable equalizer 2 detects that there is a signal present at input 2. -
Page 9: Location Of Leds And Jumpers
Frame Manual 500DA2Q-3G 3G/HD/SD-SDI Dual Reclocking Distribution Amplifier LOCATION OF LEDs AND JUMPERS INPUT 1 MODULE STATUS RECLOCKER CONFIG INPUT 1 LOCKED BYPASS (2)500DA2Q-3G INPUT 2 LOCKED RECLOCK 270Mb/s 1.5 Gb/s INPUT 1 3.0 Gb/s RECLOCKER BYPASS 270Mb/s INPUT 2 1.5 Gb/s... -
Page 10: Selecting Non-Reclock Mode
Frame Manual 500DA2Q-3G 3G/HD/SD-SDI Dual Reclocking Distribution Amplifier 5.2. SELECTING NON-RECLOCK MODE Two jumpers, located near the front of the module, determine whether each half of the module will operate as a reclocking amplifier for SMPTE 292M (1.5 Gb/s), SMPTE 259M (143 to 360 Mb/s), SMPTE 344M (540 Mb/s) or DVB-ASI video signals or as a non-reclocking distribution amplifier with other data rates. -
Page 11: Vistalink ® Remote Monitoring/Control
(GUI), third party or custom manager software may be used to monitor and control Evertz VistaLINK enabled products. ® 2. Managed devices (such as 500DA2Q-3G), each with a unique address (OID), communicate with the NMS through an SNMP Agent. Evertz VistaLINK enabled 500 series modules reside in the 3RU ®... -
Page 12: Monitor Settings Tab
Frame Manual 500DA2Q-3G 3G/HD/SD-SDI Dual Reclocking Distribution Amplifier 6.2. Monitor Settings Tab Figure 6-1: VistaLINK 500DA-3G Monitor Status Tab ® 6.2.1. Lock Status Monitor Settings Displays the current status of the video input reclocker. Monitor Settings Lock Status Locked Not Locked 6.2.2. -
Page 13: Input Video Rate
Frame Manual 500DA2Q-3G 3G/HD/SD-SDI Dual Reclocking Distribution Amplifier 6.2.3. Input Video Rate Monitor Settings Displays the detected input video rate. Monitor Settings Input Video Rate Not Valid 270M 1.5 Gbs 3.0 Gbs 6.3. Fault Traps Tab Figure 6-2: VistaLINK 500DA-3G Fault Traps Tab ®... - Page 14 Frame Manual 500DA2Q-3G 3G/HD/SD-SDI Dual Reclocking Distribution Amplifier This page left intentionally blank Page - 12 Revision 2.0...
Need help?
Do you have a question about the 500DA2Q-3G and is the answer not in the manual?
Questions and answers