Page 1
SKU: QR030 Owner’s Manual Stainless Steel Under Cabinet Range Hood THANK YOU for selecting American Standard… the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly, please read these instructions carefully before you begin.
Page 3
Safety Information (continued) Cooking Safety Information WARNING: To reduce the risk of fire, use only metal 1 . Never leave the range hood unattended when in use . duct work . Never use plastic duct work . 2 . Never cook over open flames under the range hood. WARNING: To reduce the risk of fire or electric shock, 3 .
Warranty ONE YEAR LIMITED WARRANTY A thorough inspection must be made before installation and any damage must be promptly reported. We will not be liable for failures or damage that could have been discovered or avoided by proper inspection and testing prior to installation . Conglom Kitchen &...
Pre-Installation TOOLS REQUIRED Measuring tape Level Utility knife Adjustable Pencil Duct tape wrench Flathead Needle nose Phillips screwdriver screwdriver pliers Hammer Electric drill Safety goggles Safety gloves HARDWARE INCLUDED NOTE: Hardware not shown to actual size . Part Description Quantity Long tapping screw - (M5 mm x 12 mm) Short tapping screw - (M4 mm x 8 mm) CONGLOMKB .COM...
Pre-Installation (continued) PLANNING INSTALLATION WARNING: Always wear safety goggles and gloves Number of people required: 2 or more during installation . Carefully check the range hood for damage and for missing parts prior to installation . If there is any damage or if you are missing parts, do not proceed with the installation .
Page 8
Pre-Installation (continued) Follow these guidelines when installing duct work: - Your venting system must vent to the outdoors either horizontally through the back wall (13) or vertically through the roof (14) (refer to Fig. 5/Fig. 6/Fig. 7). - Use round metal duct work with a uniform diameter of 6 in . (152 mm) . The total duct run in the venting system should be not more than 10.7 m (35 ft).
Page 9
Pre-Installation (continued) WIRING CONNECTION REQUIREMENTS DANGER: Risk of electrical shock . This range hood must be properly grounded . Installation work and electrical wiring must be done by a qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction. DANGER: Turn off the power circuit breaker or the power switch on the junction box before installing this OBSERVE ALL GOVERNING CODES AND ORDINANCES WARNINGS...
Installation Removing the electrical Removing the venting hole knock-out hole - Choose the venting hole to remove for your installation type . Use the top hole (3) for a top venting installation and WARNING: Always wear safety goggles and gloves the back hole (4) for a back venting installation .
Page 11
Installation (continued) Installing the range hood DANGER: Turn off the power circuit breaker or the power switch on the junction box before installing this unit . Touching circuitry inside the range hood while it is energized will result in death or serious injury . DANGER: If installing this unit over a gas range, turn off the gas at the source before installing or servicing this unit .
Operation NOTICE: The fan and lights operate independently of each other . Turning ON/OFF the unit Turning ON/OFF the lights - To turn on the fan, press the appropriate speed control - Press the light switch (5) to turn on and off the lights . switch [Low Speed (2), Medium Speed (3), High Speed (4)] to select the desired level of power .
Maintenance DANGER: Turn off the power circuit breaker or the power switch on the junction box before performing maintenance . Touching circuitry inside the range hood while it is energized will result in death or serious injury . WARNING: Failure to replace worn out or damaged filters will increase the risk of fire.
Care and Cleaning RANGE HOOD WARNING: Failure to maintain basic standards of care and cleaning of the range hood will increase the risk of fire. The range hood should be cleaned (regularly internally and externally) to preserve its appearance and performance . Do Not: - Always clean in the direction of the grain (original - Do not use corrosive or abrasive detergents, steel...
Troubleshooting DANGER: Turn off the power circuit breaker or the power switch on the junction box before performing maintenance . Touching circuitry inside the range hood while it is energized will result in death or serious injury . Problem Solution The range hood will not operate .
Venting Options 29.8 in. (757 mm) W High 2 x Max . 25W or 120~60Hz 320 ± Top venting QR030 35W/ JDR 16, GU10 18 in. (458 mm) D Medium twist and lock base 1.5A Back venting 9 in. (228 mm) H...
Specifications (continued) EXTERNAL DIAGRAM OF RANGE HOOD 757 mm (29.8 in) 706 mm (27.79 in) 250 mm (9.81 in) 28 mm (1.25 in) 22 mm (0.87 in) 39 mm dia. hole (1.5 in) 18 mm (0.68 in) 80 mm (3.12 in) 93.5 mm (3.68 in) 50 mm (2 in)
Service Parts If you are missing parts or if you require replacement parts, please call our customer service team at 1-877-333-0098 (Monday–Friday, 8:30 a.m.– 5 p.m., EST). Identify the required part(s) and have the part description(s) ready. Part Description Code Quantity Control Switch QHR106...
Page 19
Questions, problems, missing parts? Before returning to the store, call Customer Service 8:30 a.m.– 5 p.m., EST, Monday–Friday 1-877-333-0098 CONGLOMKB .C0M Retain this manual for future use .