Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Caliber RMD 310BT
Summary of Contents for Caliber RMD 310BT
-
Page 2: Installation
INSTALLATION PRECAUTIONS • Choose the mounting location carefully so that the unit will not interfere with the normal driving functions of the driver. • Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight or hot air from the heater, or where it would be subject to dust, dirt or excessive vibration. • Use only the supplied mounting hardware for a safe and secure installation. • Be sure to remove the front panel before installing the unit. NOTE : Inclination angle for car radio installation must not exceed 30˚ otherwise the front panel will not open. 182mm 53mm Bend these claws, if necessay NOTE: Keep the release key in the safe place as you may need it in future to remove the unit from the car. Detaching and attaching the front panel The front panel of this unit can be detached in order to prevent the unit from being stolen. -
Page 3: To Support The Unit
TO SUPPORT THE UNIT 1. UNIT . RELEASE CASE . DASH BOARD 4. HEX NUT Dashboard 5. LOCK WASHER 6. PLAIN WASHER 7. CAR BODY 8. REAR SUPPORT STRAP 9. TAPPING SCREW 10. M5 X 15 HEX BOLT WIRE CONNECTION IN / OUT CONNECTOR 2 Video Outputs: Yellow Connect to external A/V system to display Audio Out: White (L) Red (R) Connect this wire to rear seat A/V monitor system Video In: Yellow Connect to external Video equipment... -
Page 4: Maintenance
DRIVING WITH VIDEO DISPLAY By following the installation below, video will always be shown on LCD screen no matter the car is in motion or not. Steps: Connect the GRAY wire to the WHITE wire. INSTALLING REAR CAMERA FOR PARKING/REVERSE MOTION You can install an separate camera at the car rear end so when doing parking or reverse motion, the unit will automatically switch the video to the rear camera to guide the driver. CAMERA IN AUDIO OUT CAMERA IN AUDIO OUT ISO CONNECTOR VIDEO OUT 1 REAR CAMERA IN LINE OUT ISO CONNECTOR ANTENNA VIDEO OUT 1 CAMERA IN REAR CONNECTOR... -
Page 5: Locations Of Parts (Main Unit)
BlueTooth RMD 610BT 4x 75WATT LOCATIONS OF PARTS (MAIN UNIT) 11 10 RMD 610BT AUX IN BlueTooth RMD 610BT 4x 75WATT RMD 610BT 4x 75WATT (1-3) (4-6) 11 10 RMD 610BT 1. POWER ON/OFF ( . SELECT FUNCTION BUTTON . PRESET STATIONS (1,,,4,5,6) (1-3) 4. ‘AF’ FUNCTION BUTTON (ALTERNATIVE FREQUENCIES) / ANSWER CALL ( AUX IN 5. ‘TA’ FUNCTION BUTTON (TRAFFIC ANNOUNCEMENT) -
Page 6: Locations Of Parts (Remote Control)
LOCATIONS OF PARTS (REMOTE CONTROL) 1. POWER ON/OFF . MODE . PLAY/PAUSE 4. TITLE 5. SELECT Mode 6. SEEK+/SEEK- / TRACK/SEARCH 7. VOL +/VOL- 8. GOTO GOTO Dual STEP Title 9. AUDIO 10. ENTER Sub-T Setup Menu 11. NAVIGATION 1. AUTO SEEK / PRESET SCAN / REPEAT Enter 1. RANDOM / BAND / LOUDNESS 14. DUAL SEEK- SEEK+... -
Page 7: Listening To Radio
OPERATIONS Turning the unit ON/OFF ( Press “ ” button to turn on unit. To turn off, press the button again. MAIN MENU This is the root of the screen hierarchy and you can simply access all features by tapping on the touch screen buttons. Selecting a source (MODE) Press MODE repeatedly to switch between TUNER, AUX IN, USB, SD/MMC or BLUETOOTH (if Bluetooth is connected) mode. Adjusting Volume • Head Unit: Rotate VOL knob right or left to increase or decrease volume. • Remote Control: Press VOL+ or VOL- to increase or decrease volume. Mute Button • Head Unit: Press MUTE button to mute the sound at once. Press again to return to previous volume level. • Remote Control: Press button. Loud Button (LD) Press and hold LD button to turn on/off LOUD feature. Equalizer (EQ) Main Unit: On main menu, touch SETTINGS >... -
Page 8: Using The Rds Function
Auto Seek/Preset scan (A/PS) Preset Scan (PS) - By pressing shortly, the radio plays each preset station for 5 Currently Tuned Station seconds. Auto Seek (AS) - By pressing longer than 1 sec, auto seek is activated. The 6 strongest stations are preset and stored in the corresponding preset number. When Auto Seek operation is finished, the radio executes the preset scan. Storing and Recalling Frequencies If you press any of the NUMBER (1-6) you can easily store up to six broadcast frequencies for later recall with the touch of a button. -
Page 9: Listening To Mp3/Wma
. Let the movie play on until you have reached the end of the section you wish to watch on continuous loop. Once you have reached this point, press and hold A-B button again. “Rep-A-B” will appear on your screen. Playback will now start from Point A –B. 4. To stop A-B repeat playback, press and hold A-B button once more until “A-B CANCEL” disappears and normal playback resumes. Displaying information (OSD) During playback, you can see all information and current play settings. Display will show related playback time, elapse time, title number, chapter number and other information. 1. Press OSD on the remote control once. Unit will display the play time and the disc elapse time. . Press it once more and all other settings information will be displayed. Folder Name Track file names LISTENING TO MP3/WMA Repeat tracks You can choose between repeat playback of a single track or all tracks. 1. Press RPT on the remote control during playback. . Every time you press this button, the unit switches to the following settings: Repeat 1 – Repeat the current playback track. Repeat All – Repeat all folders and tracks. -
Page 10: How To Use Bluetooth In Your Car Audio
Zooming in During Playback You can zoom in into the picture during playback. 1. Press ZOOM on the remote control during playback. . Every time you press this button, the unit will zoom - - 4 - 1/ - 1/ - 1/4 times and OFF. Frame-by-frame playback This lets you move ahead one frame at a time during playback. 1 Each time you press Step button on remote control, you move ahead one frame. To return to normal playback, press PAL / NTSC (P/N) Press and hold P/N button to switch between PAL, NTSC system. Return / Go Back Press MENU on remote control to go back one level or return to previous menu. HOW TO USE BLUETOOTH IN YOUR CAR AUDIO HOW TO PERFORM PAIRING Before you can dial out from the car stereo, you must first perform PAIRING. Pairing is a procedure used to connect 2 Bluetooth devices together 1. On Main Menu, tap PHONE >... - Page 11 SETTING THE MPEG4 PLAYER You can flexibly customize the unit to suit your preference. You can set the language and other video and audio settings so when playback starts it will always use your preferred settings. Important: 1. Play any video file before you can access the setup. . Press Setup on the remote control.
-
Page 12: Technical Specifications
TECHNICAL SPECIFICATIONS MP3/WMA PLAYER SECTION Signal to Noise Ratio > 60 dB Channel Separation > 50 dB (1kHz) Frequency Response 0 Hz - 0 kHz TUNER (FM) Frequency Range 87.5-108 MHz Channel Step 50 kHz Sensitivity .8 µV Stereo Separation 0 dB Signal to Noise Ratio 50 dB LINE-OUT Output 100 mV (max.) Impedance 10k Ohm AUX-IN Frequency Response 0 Hz - 0 kHz Sensitivity 775 mV Impedance 0k Ohm GENERAL Power Supply 1V DC (10.8-15.6V allowable) Speaker Impedance 4 or 8 Ohm Output power 75W x 4CH Fuse...